IPS6041

IPS6041GTRPBF IRF | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 16

Technical content

Features

• Over temperature shutdown (with auto-restart)
• Short circuit protection (current limit)
• Reverse battery protection (turns On the MOSFET) S)PbF is a five terminal Intelligent
• Full diagnostic capability (short circuit to battery)
• Active clamp
• Open load detection in On and Off state
• Ground loss protection
• Logic ground isolated from power ground
• ESD protection

Description

R)(The IPS6041(G)( Power Switch (IPS) for use in a high side configuration. It features short circuit, over-t emperature, ESD protection, inductive load capability and diagnostic feedback. T he output current is limited to t he Ilim value. The current limitation is activated until the thermal protection acts. The over-temperature protection tu rns off the device if the junction temperature exceeds the Tshutdown value. It will automatically restart after the junction has cooled 7°C below the T shutdown value. T he reverse battery protection turns On the MOSF ET. A diagnostic pin provides different voltage levels for each fault condition. The double level shifter circuitry w ill allow large offsets between the logic and load ground. Product Summary Rds(on) 130mΩ max. Vclamp 39V I Limit 7A Open load 3V / 0.22A Packages SO8 D-Pak IPS6041GPbF IPS6041RPbF TO220 D2Pak IPS6041PbF IPS6041SPbF Typical Connection www.irf.com 1 Control Rin Load +Bat Input S ignal V Diag Rdgs Pull-up resistors required for open load off and s hort circuit to Vbat detec tion Rdgp +5V Out(4) Dg(3) Vcc(5-6-7-8) In(2) G nd(1)

IPS6041(G)(R)(S)PbF Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are referenced to Ground lead. (Tambient=25°C unless otherwise specified). Symbol Parameter Min. Max. Units Vout Maximum output voltage Vcc-35 Vcc+0.3 Voffset Maximum logic ground to load ground offset Vcc-35 Vcc+0.3 Vin Maximum input voltage -0.3 5.5 Vcc max. Maximum Vcc voltage ⎯ 36 Vcc cont. Maximum continuous Vcc voltage ⎯ 28 V Iin max. Maximum IN current -3 10 Idg max. Maximum diagnostic output current -3 10 mA Vdg Maximum diagnostic output voltage -0.3 5.5 V Maximum power dissipation (internally limited by thermal protection) Rth=100°C/W IPS6041G ⎯ 1.25 Pd Rth=50°C/W IPS6041R 1”sqrt. footprint ⎯ 2.5 W Electrostatic discharge voltage (Human body) C=100pF, R=1500Ω Between In and Vcc ⎯ 1500 Other combinations ⎯ 4000 Electrostatic discharge voltage (Machine Model) C=200pF,R=0Ω,L=10µH Between In and Vcc ⎯ 100 ESD Other combinations ⎯ 500 V Tj max. Max. storage & operating temperature junction temperature -40 150 °C Tsoldering Soldering temperature (10 seconds) ⎯ 300 °C Thermal Characteristics Symbol Parameter Typ. Max. Units Rth1 Thermal resistance junction to ambient IPS6041G 100 ⎯ Rth1 Thermal resistance junction to ambient IPS6041R D-Pak std. footprint 70 ⎯ Rth2 Thermal resistance junction to ambient IPS6041R D-Pak 1” sqrt. footprint 50 ⎯ Rth3 Thermal resistance junction to case IPS6041(R)(S) D-Pak/D2pak/TO220 6 ⎯ Rth1 Thermal resistance junction to ambient IPS6041(S) D2Pak/TO220 std. footprint 60 ⎯ Rth2 Thermal resistance junction to ambient IPS6041S D2Pak 1” sqrt. footprint 40 ⎯ °C/W Recommended Operating Conditions These values are given for a quick design. For operation outside these conditions, please consult the application notes. Symbol Parameter Min. Max. Units VIH High level input voltage 4 5.5 VIL Low level input voltage 0 0.9 Continuous drain current, Tambient=85°C, Tj=125°C, Vin=5V Rth=100°C/W IPS6041G ⎯ 1.6 Iout Rth=50°C/W IPS6041R 1” sqrt. footprint ⎯ 2.3 A Rin Recommended resistor in series with IN pin 4 10 Rdgs Recommended resistor in series with DG pin for reverse battery protection 4 20 Rdgp Recommended pull-up resistor for DG 4 20 Rol Recommended pull-up resistor for open load detection 5 100 kΩ F max. Max. switching frequency ⎯ 3.5 kHz www.irf.com 2

IPS6041(G)(R)(S)PbF Static Electrical Characteristics Max. Units Test Conditions Tj=25°C, Vcc=14V (unless otherwise specified) Symbol Pa rameter Min. Typ. ON state resistance Tj=25°C ⎯ 110 130 5 2Vin= V, Iout= .5A ON state resistance Tj=150°C ⎯ 190 230 .5A Vin=5V, Iout=2 O ⎯ 125 155 .5A N state resistance Tj=25°C, Vcc=6V Vin=5V, Iout=1 Rds(on) ON state resistance during reverse battery ⎯ 140 180 mΩ -Gn V Vcc d=14 Vcc op. Operating voltage range 6 ⎯ 28 V clamp 1 V 37 39 ⎯ t=20cc to Out clamp voltage 1 Iou mA V clamp 2 Vcc to Out clamp voltage 2 ⎯ 40 42 V t=2.5 ee F Iou A (s ig. 1) Icc Off S ⎯ 4 9 µA =0V t=0Vupply current when Off Vin , Vou Icc On S ⎯ 2.2 5 mA 5Vupply current when On Vin= Vih I nput high threshold voltage ⎯ 2.5 2.9 Vil Input low threshold voltage ⎯ 1.5 2 In hyst. Input hysteresis V 0.2 0.5 1 Iin On I n=5V nput current when device is On ⎯ 45 100 Vi Idg Dg leakage current 10 µA g=5⎯ 0.1 Vd V Vdg Low level DG voltage 5 0.4 V =1.⎯ 0.2 Idg 6mA Switching lectrical Characteris Vcc=14V, Resistive load=6 Max. Units T Conditions E tics Ω, Vin=5V, Tj=25°C Parameter Min. Typ. Symbol est Tdon Turn-on delay time ⎯ 5 15 Tr1 Rise time to Vout=Vcc-5V ⎯ 3 10 Tr2 Rise time to Vout=0.9 x Vcc ⎯ 4 20 µs dV/dt (On) Turn On dV/dt ⎯ 2.5 5 V/µs EOn T 100 ⎯ µJ urn On energy ⎯ Tdoff Turn-off delay time ⎯ 10 20 Tf F s all time to Vout=0.1 x Vcc 3 10 ⎯ µ dV/dt (Off) Turn Off dV/dt ⎯ 6.5 20 V/µs EOff T urn Off energy ⎯ 50 ⎯ µJ s gee Fi 3 www.irf.com 3

IPS6041(G)(R)(S)PbF Protection Characteristics Symbol Pa rameter Min. Typ. Max. Units Test Conditions Ilim Internal current limit V4 7 10 A out=0V Tsd+ Over temperature high threshold 150(1) 165 ⎯ Tsd- 1 °C SOver temperature low threshold ⎯ 58 ⎯ ee fig. 2 Vsc Short-circuit detection voltage(2) 2 3 4 UV 5 ⎯ 5 .9 UV hyst. 0.25 ⎯ 1.6 VOL Off Open load detection threshold 3 4 V I OL On hold 0 0.1 0.2 A Open load detection thres .05 5 2 ( aranteed (2) Reference T abl ating C OUT DG 1) Gu by design to Vcc rue T e Oper onditions IN Normal H H H Normal L L H Open Load H H L Open Load (3) L H L Short circuit to H L L Gnd Short circuit to L H Gnd L Short circuit to L (4) Vcc H H Short circuit to L Vcc (5) L H Over-temperat H L L ure Over-temperat L H ure L (3) With a pull-up resistor connected between the output and Vcc. (4) Vds lower tha (5) Without a pull-up resistor connected between the output and Vcc. Lead Assignments n 10mV. 1 2 3 4 SO8 8 7 6 5 1- Gnd 2- In 3- DG 4- Out 5-6-7-8 Vcc 1 2 3 4 5 TO220 1- Gnd 2- In 3- Vcc 4- Dg 5- Out 3- Vcc 1 2 3 4 5 D²Pak – D Pak 3- Vcc www.irf.com 4

IPS6041(G)(R)(S)PbF Functional Block Diagram All values are typical IN VCC OUT 37V Driver I Limit 43V 150k I sense C Pu harge mp Level Shifter Tj 165°C 158°C Ω 2.5V 2.0V DG GND Ground nnect Disco + Open load ver-te 20mV off O mp Open load on Short circuit 43V Vcc-gnd >UV www.irf.com 5

IPS6041(G)(R)(S)PbF www.irf.com 7 50% 100% 150% -50 0 50 100 150 200% Tj, junction temperature (°C) Fig C) Fi d inductance (mH) Load inductance (mH) Vs Ambient temperature (°C) ure 6 - Normalized Rds(on) (%) Vs Tj (° gure 7 – Max. Output current (A) Vs Loa Iout, Output current (A) Figure 8 – Max. ouput current (A) Ids, cont. Output current (A) 0.5 1.5 -50 0 50 100 150 2.5 100°C/W Tamb, Ambient temperature (°C) Fig ut current (A) Iout, Output current (A) ure 5 – Switching energy (µJ) Vs Outp Eon, Eoff, switching energy (µJ) 100 150 200 012 34 250 300 0.1 0.1 1 10 100 1000 Rds(on), Drain-to-Source On Resistance (Normalized) Eon Eoff

IPS6041(G)(R)(S)PbF www.irf.com 9 Case Outline – SO8 - Automotive Q100 PbF MSL2 qualified

IPS6041(G)(R)(S)PbF Tape & Reel SO8 www.irf.com 10

IPS6041(G)(R)(S)PbF Case Outline - TO220 (5 lead) - Automotive Q100 PbF qualified www.irf.com 11

IPS6041(G)(R)(S)PbF Case Outline 5 Lead - D2PAK - Automotive Q100 PbF MSL1 qualified www.irf.com 12

IPS6041(G)(R)(S)PbF Tape & Reel 5 Lead - D2PAK www.irf.com 13

IPS6041(G)(R)(S)PbF Case Outline 5 Lead – DPAK - Automotive Q100 PbF MSL1 qualified www.irf.com 14

IPS6041(G)(R)(S)PbF Tape & Reel 5 Lead – DPAK IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 Data and specifications subject to change without notice. TO220, D2Pak and Dpak is MSL1 qualified This product has been designed and qualified for the Automotive [Q100] market. 11/25/2006 www.irf.com 15

Note: For the most current drawings please refer to the IR website at: http://www.irf.com/package/