IPS6011PBF

IPS6011PBF IRF | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 13

Technical content

Features

• Over temperature shutdown (with auto-restart)
• Short circuit protection (current limit)
• Reverse battery protection (turns On the MOSFET) F is a five terminal Intelligent Power
• Full diagnostic capability (short circuit to battery)
• Active clamp
• Open load detection in On and Off state
• Ground loss protection
• Logic ground isolated from power ground
• ESD protection

Description

)PbThe IPS6011(S)(R Switch (IPS) for use in a high side configuration. It features short circuit, over-temperature, ESD protection, inductive load capability and diagnostic feedback. T he output current is limited to the Ilim value. The current limitation is activated until the thermal protection acts. T he over- temperature protection turns off the device if the junction temperature exceeds the Tshutdown value. It w ill automatically restart after the junction has cooled 7°C below the T shutdown value. T he reverse battery protection turns On the MOSF ET. A diagnostic pin provides different voltage levels for each fault condition. The double level shifter circuitry w ill allow large offsets between the logic and load ground. Product Summary Rds(on) 14mΩ max. Vclamp 39V I Limit 60A Open load 3V / 2.4A Packages TO-220 D²Pak D-Pak IPS6011PbF IPS6011SPbF IPS6011RPbF Typical Connection Out(5) Control Dg(4) Rin Vcc(3) Load +Bat Input S ignal V Diag In(2) Gnd(1) Rdgs Pull-up resistors required for open load off and s hort circuit to Vbat detec tion Rdgp +5V www.irf.com 1

IPS6011(S)(R)PbF Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are referenced to Ground lead. (Tambient=25°C unless otherwise specified). Symbol Parameter Min. Max. Units Vout Maximum output voltage Vcc-35 Vcc+0.3 Voffset Maximum logic ground to load ground offset Vcc-35 Vcc+0.3 Vin Maximum input voltage -0.3 5.5 Vcc max. Maximum Vcc voltage ⎯ 36 Vcc cont. Maximum continuous Vcc voltage ⎯ 28 Vcc sc. Maximum Vcc voltage with short circuit protection ⎯ 24 V Iin max. Maximum IN current -3 10 Idg max. Maximum diagnostic output current -3 10 mA Vdg Maximum diagnostic output voltage -0.3 5.5 V Maximum power dissipation (internally limited by thermal protection) Rth=5°C/W IPS6011 ⎯ 25 Rth=40°C/W IPS6011S 1”sqrt. footprint ⎯ 3.1 Pd Rth=50°C/W IPS6011R 1”sqrt. footprint ⎯ 2.5 W Electrostatic discharge voltage (Human body) C=100pF, R=1500Ω Between In and Vcc ⎯ 1500 Other combinations ⎯ 4000 Electrostatic discharge voltage (Machine Model) C=200pF,R=0Ω,L=10µH Between In and Vcc ⎯ 100 ESD Other combinations ⎯ 500 V Tj max. Max. storage & operating temperature junction temperature -40 150 °C Tsoldering Soldering temperature (10 seconds) ⎯ 300 °C Thermal Characteristics Symbol Parameter Typ. Max. Units Rth1 Thermal resistance junction to ambient IPS6011 TO220 free air 50 ⎯ Rth2 Thermal resistance junction to case IPS6011 TO220 1.2 ⎯ Rth1 Thermal resistance junction to ambient IPS6011S D²Pak std. footprint 60 ⎯ Rth2 Thermal resistance junction to ambient IPS6011S D²Pak 1” sqrt. footprint 40 ⎯ Rth3 Thermal resistance junction to case IPS6011S D²Pak 1.2 ⎯ Rth1 Thermal resistance junction to ambient IPS6011R D-Pak std. footprint 70 ⎯ Rth2 Thermal resistance junction to ambient IPS6011R D-Pak 1” sqrt. footprint 50 ⎯ Rth3 Thermal resistance junction to case IPS6011R D-Pak 1.2 ⎯ °C/W Recommended Operating Conditions These values are given for a quick design. For operation outside these conditions, please consult the application notes. Symbol Parameter Min. Max. Units VIH High level input voltage 4 5.5 VIL Low level input voltage 0 0.9 Continuous drain current, Tambient=85°C, Tj=125°C, Vin=5V Rth=5°C/W IPS6011 ⎯ 18 Rth=40°C/W IPS6011S 1” sqrt. footprint ⎯ 6.3 Iout Rth=50°C/W IPS6011R 1” sqrt. footprint ⎯ 5.6 A Rin Recommended resistor in series with IN pin 4 10 Rdgs Recommended resistor in series with DG pin for reverse battery protection 4 20 Rdgp Recommended pull-up resistor for DG 4 20 Rol Recommended pull-up resistor for open load detection 5 100 kΩ F max. Max. switching frequency ⎯ 0.3 kHz www.irf.com 2

IPS6011(S)(R)PbF Static Electrical Characteristics Max. Units Test Conditions Tj=25°C, Vcc=14V (unless otherwise specified) Symbol Pa rameter Min. Typ. ON state resistance Tj=25°C ⎯ 11 14 5 2Vin= V, Iout= 0A ON state resistance Tj=150°C ⎯ 19.5 25 0A Vin=5V, Iout=2 O ⎯ 12 17 0A N state resistance Tj=25°C, Vcc=6V Vin=5V, Iout=2 Rds(on) ON state resistance during reverse battery ⎯ 15 20 mΩ -Gn V Vcc d=14 Vcc op. Operating voltage range with short circuit p 6 ⎯ 24 rotection V clamp 1 V 39 ⎯ =50mcc to Out clamp voltage 1 37 Iout A V clamp 2 Vcc to Out clamp voltage 2 ⎯ 40 42 V =16A FigIout (see . 1) Icc Off S ⎯ 4 9 µA =0V t=0Vupply current when Off Vin , Vou Icc On S ⎯ 2.2 5 mA 5Vupply current when On Vin= Vih I nput high threshold voltage ⎯ 2.5 2.9 Vil Input low threshold voltage ⎯ 1.5 2 In hyst. Input hysteresis V 0.2 0.5 1 Iin On Input current when device is On =5V⎯ 40 100 Vin Idg D g=5V g leakage current ⎯ 0.1 10 µA Vd Vdg Low level DG voltage 5 0.4 V =1.⎯ 0.2 Idg 6mA Sw ching Vcc=14V, Resistive load=1Ω, Vin=5V, Tj=25°C Max. Units T Conditions it Electrical Characteristics Symbol Parameter Min. Typ. est Tdon Turn-on delay time ⎯ 30 60 Tr1 Rise time to Vout=Vcc-5V ⎯ 25 50 Tr2 Rise time to Vout=0.9 x Vcc ⎯ 40 100 µs dV/dt (On) Turn On dV/dt ⎯ 0.3 0.8 V/µs EOn Turn On energy ⎯ 4 ⎯ mJ Tdoff Turn-off delay time ⎯ 70 140 Tf F 80 µs all time to Vout=0.1 x Vcc ⎯ 30 dV/dt (Off) T µs urn Off dV/dt ⎯ 0.7 2 V/ EOff T urn Off energy ⎯ 1.5 ⎯ mJ see Fig 3 www.irf.com 3

IPS6011(S)(R)PbF Protection Characteristics Symbol Pa rameter Min. Typ. Max. Units Test Conditions Ilim Internal current limit V35 60 85 A out=0V Tsd+ Over temperature high threshold 150(1) 16 ⎯5 Tsd- 1 ⎯ °C SOver temperature low threshold ⎯ 58 ee fig. 2 Vsc 3 4 Short-circuit detection voltage(2) 2 UV 5 5.9 ⎯ UV hyst. 0.25 ⎯ 1.6 VOL Off detection threshold 2 3 4 V Open load I OL On Open load detection threshold 0 1 2 A .5 .6 .4 ( nteed (2) Reference T abl ting C DG 1) Guara by design to Vcc rue T e Opera onditions IN OUT Normal H H H Normal L H L Open Load H H L Open Load (3) L H L Short circuit to Gnd H L L Short circuit to L L H Gnd Short circuit to H L (4) Vcc H Short circuit to L Vcc (5) L H Over-temperat L ure H L Over-temperat L L H ure (3) With a pull-up resistor connected between the output and Vcc. (4) Vds lower tha ( ithout a pul ead Assignments n 10mV. 5) W l-up resistor connected between the output and Vcc. L 1 2 3 4 5 TO220 1- Gnd 2- In 3- Vcc 4- Dg 5- Out 3- Vcc 1 2 3 4 5 D²Pak – D Pak 3- Vcc www.irf.com 4

IPS6011(S)(R)PbF Functional Block Diagram All values are typical IN VCC OUT 37V Driver I Limit 43V 150k I sense C Pu harge mp Level Shifter Tj 165°C 158°C Ω 2.5V 2.0V DG GND Ground nnect Disco + Open load ver-te 20mV off O mp Open load on Short circuit 43V Vcc-gnd >UV www.irf.com 5

IPS6011(S)(R)PbF 4000 50% 100% 150% -50 0 50 100 150 200% -50 0 50 100 150 TO220 5°C/W D2Pak 40°C/W DPak 50°C/W Fig ut current (A) Iout, Output current (A) ure 5 – Switching energy (µJ) Vs Outp Eon, Eoff, switching energy (µJ) 0 1000 2000 3000 0 5 10 15 0.001 0.01 0.1 1 10 100 Tj, junction temperature (°C) Fig C) Rds(on), Drain-to-Source On Resistance (Normalized) Fi d inductance (mH) Load inductance (mH) Iout, Output current (A) Vs Ambient temperature (°C) Ids, cont. Output current (A) Tamb, Ambient temperature (°C) Eon Eoff ure 6 - Normalized Rds(on) (%) Vs Tj (° gure 7 – Max. Output current (A) Vs Loa Figure 8 – Max. ouput current (A) www.irf.com 7

IPS6011(S)(R)PbF www.irf.com 9 Case Outline - TO220 (5 lead) - Automotive Q100 PbF qualified

IPS6011(S)(R)PbF Case Outline 5 Lead - D2PAK - Automotive Q100 PbF MSL1 qualified www.irf.com 10

IPS6011(S)(R)PbF Tape & Reel 5 Lead - D2PAK www.irf.com 11

IPS6011(S)(R)PbF Case Outline 5 Lead – DPAK - Automotive Q100 PbF MSL1 qualified www.irf.com 12

IPS6011(S)(R)PbF Tape & Reel 5 Lead – DPAK IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 Data and specifications subject to change without notice. TO220, D2Pak and Dpak is MSL1 qualified. This product has been designed and qualified for the Automotive [Q100] market. 11/25/2006 www.irf.com 13