IPM04S0A0R10FA DELTA | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 15
Technical content
Delphi Series IPM, Non-Isolated, Integrated Point-of-Load Power Modules: 3V~5.5V input, 0.8~3.3V and 10A Output Current The Delphi Series I PM04S non -isolated, fully integrate d Point-of-Load (POL) power modules, are the latest o fferings from a world leader in power supply technology and manufacturing ― Delta Electronics, Inc. This prod uct fa mily provides up to 10A of outp ut current or 33 W of output power in an indu stry standard, compact, IC-like, molded package. It is highly integrated and does not require external components to provide the point-of-load function. A copper pad on the back of the module, in close contact with the internal heat dissipation compon ents, provide s excellent thermal performance. The assem bly proce ss of the modul es is fully auto mated with n o manual assembly involved. These co nverters possess outstanding electrical an d thermal performance, as well as extremely high reliability un der highly stressful o perating conditi ons. IPM04 S operate from a 3V~5.5V source and provide a programmable output voltage of 0.8V~3.3V. The IPM product family is available in both a SMD or SIP package. IPM family is also available for input 8V~14V, please refer to IPM12S datasheet for details. OPTIONS SMD or SIP package
APPLICATIONS
Telecom/DataCom Wireless Networks Optical Network Equipment Server and Data Storage Industrial/Test Equipment
FEATURES
High efficiency: 94% @ 5.0Vin, 3.3V/10A out Small size and low profile: Output voltage adjustment: 0.9V~3.3V Monotonic startup into normal and pre-biased loads Input UVLO, output OCP Remote ON/OFF Output short circuit protection Fixed frequency operation Copper pad to provide excellent thermal performance ISO 9001, TL 9000, ISO 14001, QS9000, OHSAS18001 certified manufacturing facility UL/cUL 60950 (US & Canada) Recognized, and TUV (EN60950) Certified CE mark meets 73/23/EEC and 93/68/EEC directives DATASHEET IPM04S0A0R/S10_12182006 Delta Electronics, Inc.
DS_IPM04S0A010_12182006 TECHNICAL SPECIFICATIONS TA = 25°C, airflow rate = 300 LFM, Vin = 5.0Vdc, nominal Vout unless otherwise noted. PARAMETER NOTES and CONDITIONS IPM04S0A0R/S10FA Min. Typ. Max. Units ABSOLUTE MAXIMUM RATINGS Input Voltage (Continuous) 0 6 Vdc Operating Temperature Refer to figure 33 for measuring point -40 +116 °C Storage Temperature -55 +125 °C INPUT CHARACTERISTICS Operating Input Voltage 3.0 3.3/5.0 5.5 V Input Under-Voltage Lockout Turn-On Voltage Threshold 2.6 2.9 V Turn-Off Voltage Threshold 1.9 2.2 V Maximum Input Current Vin=Vin,min to Vin,max, Io=Io,max 9.0 A No-Load Input Current 150 mA Off Converter Input Current 3 10 mA Input Reflected-Ripple Current P-P 1µH inductor, 5Hz to 20MHz 100 150 mAp-p Input Voltage Ripple Rejection 120 Hz TBD dB OUTPUT CHARACTERISTICS Output Voltage Set Point Vin=5.0V, Io=Io,max, Ta=25℃ - 2.5 + 2.5 % Vo,set Output Voltage Adjustable Range 0.8 3.3 V Output Voltage Regulation Over Line Vin=Vin,min to Vin,max 10 mV Over Load Io=Io,min to Io,max 15 mV Over Temperature Ta=Ta,min to Ta,max 15 mV Total Output Voltage Range Over sample load, line and temperature -3.0 +3.0 % Vo,set Output Voltage Ripple and Noise 5Hz to 20MHz bandwidth Peak-to-Peak Full Load, 1µF ceramic, 10µF tantalum 50 100 mVp-p RMS Full Load, 1µF ceramic, 10µF tantalum 10 15 mV Output Current Range 0 10 A Output Voltage Over-shoot at Start-up Vin=3.0V to 5.5V, Io=0A to 10A, Ta=25℃ 0 3 % Vo,set Output DC Current-Limit Inception 220 % Io DYNAMIC CHARACTERISTICS Dynamic Load Response 10µF Tan & 1µF Ceramic load cap, 0.5A/µs Positive Step Change in Output Current 50% Io, max to 100% Io, max 130 165 mVpk Negative Step Change in Output Current 100% Io, max to 50% Io, max 130 165 mVpk Setting Time to 10% of Peak Devitation 25 50 µs Turn-On Transient Io=Io.max Start-Up Time, From On/Off Control 5 12 20 ms Start-Up Time, From Input 5 12 20 ms Output Voltage Rise Time Time for Vo to rise from 10% to 90% of Vo,set, 3 5 7 ms Maximum Output Startup Capacitive Load Full load; ESR ≧1mΩ 1000 µF Full load; ESR ≧10mΩ 5000 µF EFFICIENCY Vo=0.9V Vin=5.0V, Io=Io,max, Ta=25℃ 81.0 % Vo=1.2V Vin=5.0V, Io=Io,max, Ta=25℃ 85.0 % Vo=1.5V Vin=5.0V, Io=Io,max, Ta=25℃ 88.0 % Vo=1.8V Vin=5.0V, Io=Io,max, Ta=25℃ 90.0 % Vo=2.5V Vin=5.0V, Io=Io,max, Ta=25℃ 92.5 % Vo=3.3V Vin=5.0V, Io=Io,max, Ta=25℃ 94.0 % FEATURE CHARACTERISTICS Switching Frequency 300 kHz ON/OFF Control, (Logic High-Module ON) Logic High Module On 2.2 Vin,max V Logic Low Module Off -0.2 0.8 V ON/OFF Current Ion/off at Von/off=0 0.25 1 mA Leakage Current Logic High, Von/off=5V 50 µA GENERAL SPECIFICATIONS MTBF Io=80% Io,max, Ta=25℃ 13.3 M hours Weight 6 grams
DS_IPM04S0A010_12182006 DESIGN CONSIDERATIONS Safety Considerations For safety-agency approval the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standards. For the co nverter output to be con sidered meeting the requirements of safety extra-lo w volt age (SEL V), the input must meet SELV requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. The input to these unit s is to be provided with a maximum 10A time-delay fuse in the ungrounded lead. Remote On/Off The IPM se ries power modules have a n On/Off control pin for output volt age remote On/Of f ope ration. The On/Off pin is an open coll ector/drain logic input si gnal that is referenced to ground. When On/Off control pin is not used, leave the pin unconnected. The remote on/off pin i s internally connected to +Vin through an internal pull-up resistor. Figure 27 shows the circuit configuration fo r a pplying the remote on/of f pin. The module will execute a sof t st art ON when t he transistor Q1 is in the off state. The typical ri se for this re mote on/off pin at the output voltage of 0.9V and 3.3V are shown in Figure 17 and 18. Vo On/Off Vin GND IPM RL Figure 27: Remote on/off implementation FEATURES DESCRIPTIONS Over-Current Protection To provide prote ction in an output over load fa ult condition, the unit is equip ped with internal over-current protection. When the over-cu rrent prote ction is triggered, the unit enters hiccup m ode. The u nits operate normally once the fault condition is removed. Pre-Bias Startup Capability The IPM would perform the monotoni c st artup into the pre-bias load s; so as to avoid a system volt age dro p occur u pon application. In compl ex digit al system s an external volt age can so metimes b e pre sented at the output of the module during power on. This voltage may be feedb ack throug h a multi-supply logic component, such a s FP GA or ASIC. Another wa y might be via a clamp di ode as p art o f a power up seq uencing implementation.
DS_IPM04S0A010_12182006 The amo unt of powe r del ivered by th e modul e is the voltage at th e output terminals multiplied by the o utput current. When using the trim feature, the output volt age of the modul e can be in creased, whi ch at the sa me output curre nt would incre ase the po wer output of the module. Care sho uld b e t aken to ensure that the maximum output powe r of the module must not excee d the maximum rated power (Vo.set x Io.max ≤ P max). Voltage Margining Output voltage margining can be implemented in the IPM modules by connecting a resistor, Rmargin-up, from the Trim pin to the ground pin for margining-up the output voltage and by connecting a resistor, Rmargin-down, from the Trim pin to the output pin for marg ining-down. Figure 31 sh ows the circuit configuration fo r output volt age marginin g. If unused, leave the trim pin unconnected. Vo On/Off Vin GND Trim IPM Rmargin-up Rmargin-down Rtrim Figure 31: Circuit configuration for output voltage margining FEATURE DESCRIPTIONS (CON.) Table 1 provides Rtrim values required for some common output voltages, while Table 2 provid es value of externa l voltage so urce, Vtrim, for the same common o utput voltages. By using a 0.5% tolerance resistor, set point tolerance of ±2.5% can b e achieved as spe cified in the electrical specification. Table 1 VO (V) Rtrim (Ω)
0.9 Open
1.2 23.146K 1.5 11.479K 1.8 7.590K 2.5 4.188K 3.3 2.729K Table 2 VO (V) Vtrim (V) 0.9 0.7000 1.2 0.6943 1.5 0.6887 1.8 0.6831 2.5 0.6700 3.3 0.6551
DS_IPM04S0A010_12182006 PICK AND PLACE LOCATION SURFACE- MOUNT TAPE & REEL All dimensions are in millimeters (inches) All dimensions are in millimeters (inches) LEAD FREE PROCESS RECOMMEND TEMP. PROFILE Temp. Time Note: All temperature refers to topside of the package, measured on the package body surface. LEADED (Sn/Pb) PROCESS RECOMMEND TEMP. PROFILE Temp. Time 100℃ 150℃ 60~150 sec 60 ~ 120 sec 183℃ Preheat time Ramp up max. 3℃/sec Ramp down max. 4℃/sec Peak Temp. ~ 225 ℃ 25℃ Note: All temperature refers to assembly application board, measured on the land of assembly application board. 150℃ 200℃ 90~150 sec Time Limited 60 sec above 210℃ 210℃ Preheat time Ramp up max. 3℃/sec Ramp down max. 4℃/sec Peak Temp. ~ 220 ℃ 25℃
DS_IPM04S0A010_12182006 MECHANICAL DRAWING SMD PACKAGE S IP PACKAGE RECOMMEND PWB PAD LAYOUT RECOMMEND PWB HOLE LAYOUT 1 234 5 Note: The copper pad is recommended to connect to the ground. 12 3 4 5 12 3 4 5 Note: All dimension are in millimeters (inches) standard dimension tolerance is± 0.10(0.00 4”)
DS_IPM04S0A010_12182006 PART NUMBERING SYSTEM IPM 04 S 0A0 R 10 F A Product Family Input Voltage Number of Outputs Output Voltage Package Output Current Option Code Integrated POL Module 04 - 3V ~ 5.5V 12 - 8V ~ 14V S - Single 0A0 - programmable output R - SIP S - SMD 08 - 8A 10 - 10A F- RoHS 6/6 (Lead Free) A - Standard Functions MODEL LIST Model Name Packaging Input Voltage Output Voltage Output Current Efficiency (Typical @ full IPM12S0A0R08FA SIP 8V ~ 14V 0.8V ~ 5V 8A 93% IPM12S0A0S08FA SMD 8V ~ 14V 0.8V ~ 5V 8A 93% IPM04S0A0R10FA SIP 3V ~ 5.5V 0.8V ~ 3.3V 10A 94% IPM04S0A0S10FA SMD 3V ~ 5.5V 0.8V ~ 3.3V 10A 94% CONTACT: www.delta.com.tw/dcdc USA: Telephone: East Coast: (888) 335 8201 West Coast: (888) 335 8208 Fax: (978) 656 3964 Email: DCDC@delta-corp.com Europe: Phone: +41 31 998 53 11 Fax: +41 31 998 53 53 Email: DCDC@delta-es.com Asia & the rest of world: Telephone: +886 3 4526107 ext 6220 Fax: +886 3 4513485 Email: DCDC@delta.com.twT WARRANTY Delta offers a two (2) year limited warranty. Complete warranty information is listed on our web site or is available upon request from Delta. Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by Delta for its use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right to revise these specifications at any time, without notice.