IMP ASTEC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

Business-Critical Continuity Intelligent MP Series Up to 1500 Watts Special Features

  • Full Medical EN60601 Approval
  • Intelligent I 2C Control
  • Configurable Current Share on all outputs >10A
  • Voltage adjustment on all out- puts (Manual or I2C)
  • Configurable Input and Output OK signals and indicators
  • Configurable Inhibit/Enable
  • Configurable Output UP/DOWN sequencing
  • Intelligent fan (speed control/fault status)
  • Customer Provided Air Option
  • uP Controlled PFC input with active Inrush protection 2C monitor of Voltage, Current, and Temp
  • IPMI Compliant
  • Programmable Voltage, Current Limit, Inhibit/Enable through I2C
  • Optional Extended Hold-up Module (Semi F47 compliance)
  • Power density increased by 50%
  • Backward compatibility with standard MP
  • External switching frequency sync input
  • Optional Conformal Coating
  • Industrial Temp Range
  • No preload required Total Power: Up to 1500 Watts Input Voltage: 85 - 264 VAC 120-300 VDC # of Outputs: Up to 21 Electrical Specifications TM RoHS Rev. 1.30.06 iMP Series 1o f 8 Input Input range 85-264 VAC: 120-350 VDC (Limited to 300VDC in medical applications) Frequency 47-440 Hz Inrush current 40A peak max. (soft start) Efficiency up to 85% @ full case load Power Factor 0.99 typ. meets EN61000-3-2 Turn-on time AC on 1.5 sec typ., Inhibit / Enable 150 ms typ. Programmable EMI Filter CISPR 22 / EN55022 Level “B” Leakage current 300 μA max. @ 240 VAC; 47-63Hz Radiated EMI CISPR 22 / EN55022 Level “B” Holdover storage 20 ms minimum (independent of input VAC) additional 34mSEC holdover storage with optional HUP module (Semi F47 compatible) AC OK >5 ms early warning min. before outputs lose regulation. Programmable. Full cycle ride thru (50 Hz) Harmonic distortion Meets EN61000-3-2 Isolation Meets EN60950 and EN60601 Global Inhibit/Enable TTL, Logic “1” and Logic “0”. Configurable. Input fuse (internal) iMP4: 10A; iMP8: 20A; iMP1: 20A (both lines fused) Warranty 2 years

Rev. 1.30.06 iMP Series 2o f 8 Output Adjustment range* ±10% minimum all outputs (manual) (full module adjustment range using II22CC) Margining ±4-6% nominal analog (single output module only) Overall reg 0.4% or 20 mV max. (36W modules 4% max.) Ripple RMS: 0.1% or 10 mV, whichever is greater Pk-Pk: 1.0% or 50 mV, whichever is greater Bandwidth limited to 20 MHz Dynamic response <2% or 100 mV, with 25% load step Recovery time To within 1% in <300 μsec. Overcurrent protection* Configurable through II22CC. Single output module and main out- put of the dual output module 105-120% of rated output cur- rent. Aux output of dual output module 105-140% of rated output current Triple output module internally protected Short circuit protection Protected for continuous short circuit Recovery is automatic upon removal of short Overvoltage protection* Configurable through I2C Single output module 2-5.5V 122-134% ; 6-60V 110-120% Dual output module 2-6V 122-134% ; 8-28V 110-120% Triple output module No overvoltage protection provided Reverse voltage protection 100% of rated output current Thermal protection* Configurable through II22CC All outputs disabled when internal temp exceeds safe operat- ing range. >5 ms warning (AC OK signal) before shutdown Remote sense Up to 0.5 V total drop (not available on triple output module) Singlewire parallel Configurable through firmware Current share to within 2% of total rated current DDCC OOKK** +/-5% of nominal. Configurable through II22CC Minimum load Not required Housekeeping bias voltage 5 VDC @1.0Amp max. present whenever AC input is applied Module inhibit* Configured and controlled through II22CC Switching frequency 250 kHz accepts external sync signal Output/Output isolation >1 Megohm, 500V VME signal* DC OK signal programmable through II22CC to function as POR signal *Can be controlled via I2C Safety UL UL60950/UL2601 CSA CSA22.2 No. 234 Level 5 VDE EN60950/EN60601 BABT Compliance to EN 60950/EN60601 BS 7002 CB Certificate and report CE Mark to LVD Module Code 11 22 33 44 NNoonnee Module Type SSiinnggllee SSiinnggllee SSiinnggllee DDuuaall TTrriippllee Max output power 210W 360W 750W 144W 36W Max output current 35A 60A 150A 10A 2A Output voltages available* 2-60V 2-60V 2-60V 5, 12-15, 28-30V 2-6, 12-15, 28-30V 8-15V 8-28V 2-28V Standard voltage increments 25 25 25 19 18 Remote sense Yes Yes Yes Yes Yes No No No Remote margin Yes Yes Yes No No No No No V-Program - I2C Control Yes Yes Yes Yes Yes Yes Yes Yes Active Current Share Yes Yes Yes Yes No No No No Module Inhibit - I2C Control Yes Yes Yes Yes Yes Yes Yes Yes Module Inhibit - Analog Yes Yes Yes No No No No No Over voltage / Over current protection Yes Yes Yes Yes Yes Yes Yes Yes Minimum load required No No No No No No No No Slots occupied in any iMP case 1 2 3 1 1 Output Module Line-up *Programmable Operating temperature -40° to 70°C ambient. Derate each output 2.5% per degree from 50° to 70°C. ( -20°C start up) Storage temperature -40°C to +85°C Electromagnetic susceptibility Designed to meet EN61000- Level 3 Humidity Operating; non-condensing 10% to 95% RH Vibration IEC68-2-6 to the levels of IEC721-3-2 MTBF demonstrated >550,000 hours at full load, 220VAC and 25°C ambient conditions Environmental Specifications

Business-Critical Continuity Rev. 1.30.06 iMP Series 3o f 8 Voltage Voltage Code Single Output Module Code Dual Output Triple Output II22CC Adjustment Ranges1 2 3 V1 V2 V1 V2 V3 2V A 35A 60A 150A — 10A — — 2A 1.8 - 6.1 2.2V B 35A 60A 150A — 10A — — 2A 3V C 35A 60A 150A — 10A — — 2A 3.3V D 35A 60A 150A — 10A — — 2A 5V E 35A 60A 150A 10A 10A — — 2A 5.2V F 35A 60A 150A — 10A — — 2A 5.5V G 34A 58A 137A — 10A — — 2A 6.0V H 23A 42A 80A — 10A — — 2A 5.4 - 13.2 8.0V I 20A 36A 80A — — 1A 1A 1A 10V J 18A 32A 75A — — 1A 1A 1A 11V K 17A 31A 68A — — 1A 1A 1A 12V L 17A 30A 62.5A 10A 4A 1A 1A 1A 14V M 14A 21A 53.5A 9A 4A 1A 1A 1A 12.6 - 22.015V N 14A 20A 50A 8A 4A 1A 1A 1A 18V O 11A 19A 41.6A — — — 0.5A 0.5A 20V P 10.5A 18A 37.5A — — — 0.5A 0.5A 24V Q 8.5A 15A 31.3A 4A 2A — 0.5A 0.5A 21.6 - 39.6 30V S 6.5A 12A 25A — — — 33V T 6.2A 11A 22.7A — — — — — 36V U 5.8A 10A 20.8A — — — — — Non-std* Z Special Voltage - Consult Factory for specifications *Note: Increments of current not shown can be achieved by paralleling modules (add currents of each module selected). 76 5 43 21 iMP4 available slots iMP8 available slots Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 6 Slot 1 Slot 2 Slot 3 Slot 4 Slot 6 Slot 7 Slot 5 iMP1 available slots PARALLEL CODES 0 = no parallel 1 = 1 & 2 2 = 2 & 3 3 = 3 & 4 4 = 4 & 5 5 = 3 & 4 & 5 6 = 5 & 6 7 = 4 & 5 & 6 8 = 6 & 7 9 = 3 & 4, 6 & 7

Ordering Information

Output Module Voltage/Current iMP1* - 3L0 - 2E2 - 1Q1 - 4LL0 - 00 - A - ### Case Size (mm) 4 = 2.5" x 5" x 10"; 750W - 1100W, 5 Slots (63.5 x 127 x 254) 8 = 2.5" x 7" x 10"; 1000W - 1200W, 6 Slots (63.5 x 177.8 x 254) 1 = 2.5" x 8" x 11"; 1200W - 1500W, 7 Slots (63.5 x 203.2 x 279.4) *Note: Add "-E" after iMP4 to denote IEC (Not available on iMP8 or iMP1.) Module Codes Module/Voltage/Option Codes Module Codes: (None) = 36W Triple O/P (1 slot) 1 = 210W Single O/P (1 slot) 2 = 360W Single O/P (2 slot) 3 = 750W Single O/P (3 slot) 4 = 144W Dual O/P (1 slot) 5 - 9 = Future Case Option Codes First Digit 0 - 9 = Parallel Code Second Digit 0 = No Options 1 = Reverse Air 2 = Extended Hold Up (1 slot)* 3 = Global Enable 4 = Fan Off w/Inhibit 5 = Opt 1 + Opt 3 6 = Opt 1 + Opt 4 7 = Opt 3 + Opt 4 8 = Opt 1 +3 +4 9 = Future *Meets Semi F47 Software Code Hardware Code Voltage Codes: See Output Module Voltage/Current table above Option Codes: 0 = Standard 1 = Module Enable 2 = Constant Current 3 - 9 = Future Module/Voltage/Option Codes First - Module Code Second - Voltage Code Third - Option Code Case Option Codes Factory Assigned for Modified Standards Standard is "A" - Software Code "Blank" - Hardware Code Case Size

Business-Critical Continuity Rev. 1.30.06 iMP Series 4o f 8 Drawings DC-DC Converter Output Modules Control Signal Information, J1 Control Connector Pin No. Function 1 + Remote Sense single or dual o/p main 2 Remote Margin / V. Program single o/p

3 Margin High single o/p

4 - Remote Sense / Margin Low single or dual o/p main

5 Spare

6 Module, Isolated Inhibit single or dual o/p

7 Module Inhibit return single or dual o/p

8 Current Share (SWP) single or dual o/p main

9 + Remote Sense V2 dual o/p, single is spare 10 - Remote Sense V2 dual o/p, single is spare *Note: All iMP modules have a green DCOK LED. V2 ADJ V1 ADJ PIN 1 V3 ADJ DC OUTPUT CONNECTION .48 (12.1) V1+ V1- V2+ V2- V3+ V3- .84 (21.3) PIN 1 M4X8 SCREWS (4X) V ADJ .32 (8.1) .44 (11.3) (2X) (2X) .33 (8.5) .63 (16.0) M4X8 SCREWS (4X) PIN 1 V ADJ .44 (11.3) .32 (8.1) 1.24 (31.6) (2X) .61 (15.6) (2X) .63 (16.0).59 (15.0) PIN 1 .32 (8.1) .44 (11.2 ) (2X) M4X8 SCREWS (2X) V ADJ .48 (12.1) .44 (11.3) 1.38 (35.1) PIN 1 V1 ADJ .32 (8.1) .42 (10.7) V1 + V1 - V2 - V2 + M3X8 SCREWS (4X) .46 (11.7) (4X) .30 (7.5)(3X) V2 ADJ 1.17 (29.7) Single 210 Watt Dual 144 Watt Triple 36 Watt Single 360 Watt Single 250 Watt iMP Modules

Business-Critical Continuity Rev. 1.30.06 iMP Series 5o f 8 Notes 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 cri mp contacts (Molex C - Grid III Series) or AMP Model number 87977-3 with 87309-8 pins. Connector kit includes mating connector and 10 pins, Astec part #70-841-004. J2 10 position housing (Landwin 2051P1000T). Mates with housing 205051000 (Landwin) with 2053T011P (Lan dwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10in-lbs. Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. Triple O/P module is .045” square pins on .156” centers. Mates with Molex 09-50-8063 or equivalent. iMP Series iMP4 (750/1100 Watts Max) 55--IInncchh CCaassee SSiizzee:: iMP4: 2.5” x 5” x 10” (63.5mm x 127mm x 254mm) Horizontal both sides

Business-Critical Continuity Rev. 1.30.06 iMP Series 6o f 8 #8-32 MTG HOLES (4X) MARKED AS Y M4 MTG HOLES (4X) MARKED AS X M4 MOUNTING HOLES (4X) MARKED AS Xy y x x iMP Series iMP8 (1000/1200 Watts Max) 77--IInncchh CCaassee SSiizzee:: iMP8: 2.5” x 7” x 10” (63.5mm x 177.8mm x 254mm) Notes 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 cri mp contacts (Molex C - Grid III Series) or AMP Model number 87977-3 with 87309-8 pins. Connector kit includes mating connector and 10 pins, Astec part #70-841-004. J2 10 position housing (Landwin 2051P1000T). Mates with housing 205051000 (Landwin) with 2053T011P (Lan dwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10in-lbs. Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. Triple O/P module is .045” square pins on .156 centers. Mates with Molex 09-50-8063 or equivalent.

Business-Critical Continuity Rev. 1.30.06 iMP Series 7o f 8 x y xx x y y y 171.45 171.45 177.8

19.05 M4 MOUNTING HOLES (4X)

#8-32 MOUNTING HOLES (4X) MARKED AS Y M4 MOUNTING HOLES (4X) IDENTICAL BOTH SIDES 38.10 88--IInncchh CCaassee SSiizzee:: iMP1: 2.5” x 8” x 11” (63.5mm x 203.2mm x 279.4mm) Notes 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 cri mp contacts (Molex C - Grid III Series) or AMP Model number 87977-3 with 87309-8 pins. Connector kit includes mating connector and 10 pins, Astec part #70-841-004. J2 10 position housing (Landwin 2051P1000T). Mates with housing 205051000 (Landwin) with 2053T011P (Lan dwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive. 4. All dimensions are in millimeters and inches, and are typical. 6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10in-lbs. Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. Triple O/P module is .045” square pins on .156 centers. Mates with Molex 09-50-8063 or equivalent. iMP Series iMP1 (1200/1500 Watts Max)

service marks of Emerson Electric Co. business-critical continuity.

5810 Van Allen Way

information or for any errors or omissions.

1 AC Neutral

2 AC Line (Hot)

3 Chassis (Earth) Ground

1 Input AC OK - "Emitter"

2 Input AC OK - "Collector"

3 Global DC OK - "Emitter"

4 Global DC OK - "Collector"

5 External Sync

6 Gobal Inhibit / Optional Enable Logic "0"

7 Gobal Inhibit / Optional Enable Logic "1"

8 Gobal Inhibit / Optional Enable Return

2 Serial Data Signal

3 Secondary Return

4 Serial Clock Signal

5 Address Bit 2

6 Address Bit 1

7 Address Bit 0

8 No connection

Figure 1. AC Input Figure 2. Connector J1 Figure 3. Connector J2