IL339 ETC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Quad Single Supply Comparator The IL339 consists of four independent precision voltage comparators with an offset voltage specification as low as 2.0 mV max for four comparators which were designed specifically to operate from a single power supply over a wide range of voltages. Application areas include limit comparators, simple analog to digital converters; pulse, squarewave and time delay generators; wide range VCO; MOS clock timers; multivibrators and high voltage digital logic gates.
- Single or Split Supply Operation
- Low Input Bias Current
- Low Input Offset Current
- Input Common Mode Voltage Range to Gnd
- Low Output Saturation Voltage
- TTL and CMOS Compatible IL339
ORDERING INFORMATION
TA = 0° to 70° C for all packages. LOGIC DIAGRAM PIN 3 = VCC PIN 12 = GND PIN ASSIGNMENT
MAXIMUM RATINGS* Symbol Parameter Value Unit VCC Power Supply Voltages Single Supply Split Supplies ±18 V VIDR Input Differential Voltage Range 36 V VICR Input Common Mode Voltage Range (1) -0.3 to V CC V ISC Output Short Circuit to Ground Continuous IIN Input Current, per pin (2) 50 mA TJ Junction Temperature Plastic Packages 150 °C Tstg Storage Temperature -65 to +150 °C TL Lead Temperature, 1mm from Case for 10 Seconds 260 °C PD Power Dissipation @TA=25°C Plastic Package Derate above 25°C 1.0 8.0 W mW/°C *Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. Notes: 1. Split Power Supplies. 2. V IN<-0.3V. This input current will only exist when voltage at any of the input leads is driven negative. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit VCC DC Supply Voltage ±2.5 or 5.0 ±15 or V TA Operating Temperature, All Package Types 0 +70 °C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, V IN and V OUT should be constrained to the range GND≤(VIN or VOUT)≤VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or V CC). Unused outputs must be left open.
DC ELECTRICAL CHARACTERISTICS(TA=0 to +70°C) Guaranteed Limit Symbol Parameter Test Conditions Min Typ Max Unit VIO Input Offset Voltage V 0=1.4V VCC=5.0-30V;RS≤100Ω VICR=0V - (VCC-1.5)V -9 . 0 m V IIB Input Bias Current V 0=1.4V VCC=5.0-30V VICR=0V - (VCC-1.5)V - 400 nA IIO Input Offset Current V 0=1.4V VCC=5.0-30V VICR=0V - (VCC-1.5)V - ±150 nA VICR Input Common Mode Voltage Range VCC=5.0-30V 0 V CC- 2.0V V ICC Supply Current RL=∞ ,VCC=5.0 RL=∞ ,VCC=30V 2.0* 2.5* mA AVOL Voltage Gain VCC=15V, RL=15KΩ - 200* - V/mV t1 Large Signal Response Time VIN=TTL Logic Swing, Vref=1.4V, VCC=5.0V, RL=5.1KΩ , VRL=5.0V - 300* - ns t2 Response Time VCC=5.0V, RL=5.1KΩ , VRL=5.0V -1 . 3 * - µs Isink Output Sink Current V I(-)=1.0V, VI(+)=0V, V0≤1.5V, VCC=5.0V 6.0* - - mA Vsat Saturation Voltage V I(-)=1.0V, VI(+)=0V, Isink≤4.0mA, VCC=5.0V - - 700 mV IOL Output Leakage Current VI(+)=1.0V, VI(-)=0V, V0=5.0V V0=30V 0.1* 1000 nA VIDR Differential Input Voltage Range All VIN≥GND or V-Supply (if used) VCC*V *=@25°C