IH5352 INTERSIL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

Features

  • Switch Attenuation Varies Less Than 3dB From DC to 100MHz
  • Compatible With TTL, CMOS Logic
  • Wide Operating Power Supply Range
  • “Break-Before-Make” Switching

Applications

  • Video Switch
  • Communications Equipment
  • Disk Drives
  • Instrumentation
  • C A T V Functional Diagram SWITCH STATE SHOWN FOR LOGIC “0” INPUT

Ordering Information

TEMP. RANGE ( oC) PACKAGE PKG. NO. IH5352CPE 0 to 70 16 Ld PDIP E16.3 IH5352CBP 0 to 70 20 Ld SOIC M20.314 IIN1 IIN2 IIN3 IIN4 D 1 D 2 GND D 3 D 4 VL 1IIN1 NC IIN2 IIN3 NC IIN4 D 1 NC D 2 GND D 3 NC D 4 VL TRUTH TABLE LOGIC SWITCHES

0 Off

5kΩ 10kΩ Q 1 Q 8 Q 9 Q 10 +15V +5V Q 5 Q 3 3kΩ5kΩ Q 4 -15V Q 6 Q 20 Q 19 +15V -15V Q 12 Q 11 +15V Q 14 +15V Q 18 Q 16 Q 21 Q 15 +15V Q 13 D S Q 22 -15V Q 17 -15V TTL IH5352

Absolute Maximum Ratings Thermal Information V Operating Conditions Supply Voltage Range Thermal Resistance (Typical, Note 1) θJA (oC/W) (SOIC - Lead Tips Only) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operationo ft h e device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical SpecificationsV+ = +15V, VL = +5V, V- = -15V, Unless Otherwise Specified PARAMETER TEST CONDITIONS (NOTE 2) TYP 25oC (NOTE 4) UNITS0oC2 5 oC7 0 oC DYNAMIC CHARACTERISTICS Turn ON Time, t ON Figure 1 150 - - - ns Turn OFF Time, tOFF 80 - - - ns OFF Isolation, OIRR Figure 2 70 - - - dB Crosstalk, CCRR Figure 3 -60 - - - dB Switch Attenuation 3dB Frequency, f 3dB Figure 4 100 - - - MHz DIGITAL INPUT CHARACTERISTICS Logic “1” Input Voltage, V IH >2.4 - - - V Logic “0” Input Voltage, VIL <0.8 - - - V Input Logic Current, IIN VIN > 2.4V or < 0V 0.1 ±1 ±11 0 µA ANALOG SWITCH CHARACTERISTICS Drain-Source ON Resistance, r DS(ON) VD =±5V, IS = 10mA, VIN ≥ 2.4V 50 75 75 100 Ω VD =±10V, IS = 10mA, VIN ≥ 2.4V 100 150 150 175 Ω V+ = VL = +5V, VIN = 3V, V- = -5V, VD = ±3V, IS = 10mA 175 300 300 350 Ω On Resistance Match Between Channels,ΔrDS(ON) IS = 10mA, VD =±5 V 5 --- Ω Switch OFF Leakage Current, ID(OFF) or IS(OFF) VS/D =±5V or ±14V, VIN ≤ 0.8V (Note 3) - - ±2 100 nA Switch ON Leakage Current, ID(ON) + IS(ON) VS/D =±5V or±14V, VIN ≥ 2.4V - - ±2 100 nA POWER SUPPLY CHARACTERISTICS Positive Supply Quiescent Current, I+ V IN = 0V or +5V 0.1 1 1 10 µA Negative Supply Quiescent Current, I- 0.1 1 1 10 µA Logic Supply Quiescent Current, IL 0.1 1 1 10 µA NOTES: 2. Typical values are not tested in production. They are given as a design aid only. 3. Positive and negative voltages applied to opposite sides of switch, in both directions successively. 4. Min or Max value, unless otherwise specified. IH5352

All Intersil semiconductor products are manufactured, assembled and tested underISO9000 quality systems certification. Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time with- out notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web sitehttp://www.intersil.com Die Characteristics DIE DIMENSIONS: 2617µm x 5233µm METALLIZATION: Type: Al Thickness: 10kÅ ±1kÅ PASSIVATION: Type: PSG/Nitride PSG Thickness: 7kÅ ±1.4kÅ Nitride Thickness: 8kÅ ±1.2kÅ WORST CASE CURRENT DENSITY: 9.1 x 104 A/cm2 Metallization Mask Layout IH5352 S1 IN1 D 1 GND D 2 D 4 D 3 IN2 IN3 IN4 (SUBSTRATE) VL IH5352