IB2412N-6FWL-224 ILLUMINANT | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 21
Technical content
Datasheet sections
- 2 Mechanical Diagram
MODEL NAME : IB2412N-6FWL-224 VER : A CHECKED BY: ORGAN IZED BY: 200 7.05.22 北極光企業有限公司 ILLUMINANT CO., LTD. 台北辦公室 Taipei Office 台北市民權東路 3 段 75 巷 15 號 1 樓 1F,#15,Lane 75,Min Chuan E. Rd,Sec 3,Taipei,Taiwan. Tel:+886-2-25175115 Fax:+886-2-25175099 深圳辦公室 Shenzhen office 深圳市南山區科技園北區朗山路 8 號東部物業大廈 5 樓 5F Dongwu Commercial Building,Lanshan Rd, North Distnist,Hi-tech Industrial Park, Shenzhen,PRC Tel:+86-755-86154466 Fax:+86-755-86154366
Ver : A 2/21 LCM SAMPLE APPROVAL (液 晶 顯 示 模 組 樣 品 確 認 書 ) １． PART A:FILLED BY ILLUMINANT（由 ILL填寫） 4) LCM Function (LCM 內容)： A LCD TYPE (LCD 種類)：□ TN, □ HTN, □ STN, ■ FSTN ( ■ POSITIVE/正向, □ NEGATIVE/ 反向, □ BLACK MASK/ 內黑絲印) B VIEWING AREA ( 視角方向)：□ 3H, ■ 6H, □ 9H, □ 12H C POLARIZER COLOR ( 偏光板顏色)：■ GRAY/灰色, □ YELLOW GREEN/黃綠色, □ BLUE/ 藍色, □ BLACK/ 黑色 D BACKLIGHT COLOR ( 背光顏色)：□ YELLOW GREEN/ 黃綠光, □ ORANGE/ 橘光 □ RED/紅光, □ BLUE/藍光, □ GREEN/翠綠光, ■ WHITE/白光 E TEMPERATURE ( 溫度)：□ NORMAL/ 常溫, ■ WIDE/廣溫 F PCB RESISTOR (PCB 板電阻)：Y1 ( MHz), R2 ( 82K Ω), R3/R4/R6/R7 ( 2KΩ), G CONTROL IC ( 控制 IC)：T6963C or equivalent ２．PART B:FILLED BY CUSTOMER （請客戶填寫） CHECK LIST ITEMS（檢查項目）： ＯＫ ＮＧ REASON（原因） APPROVED BY（批准）： D A T E O F A P P R O V A L （批准日期）：
Ver : A 3/21 * All of our STN Panel belong “WIDE TEMPERATURE”
Ver : A 5/21 1. Mechanical Specification ITEM STANDARD VALUE UNIT DOT MATRIX FORMAT 240 X 128 DOTS -- CONTROLLER IC T6963C or equivalent MODULE DIMENSION CCFL BACKLIGHT 144.0W × 104.0H × 13.0D mm MODULE DIMENSION EDGE LED BACKLIGHT 144.0W × 104.0H × 13.0D mm VIEWING DISPLAY AREA 114.0W × 61.0H mm mm ACTIVE DISPLAY AREA 105.56W × 56.28H mm mm DOT SIZE 0.40W × 0.40H mm mm DOT PITCH 0.44W × 0.44H mm mm z CCFL USE INVERTER TYPE FL001-5A / FL001-12A INVERTER INPUT DC +5V / DC +12V V 360 / 180 mA INVERTER OUTPUT AC 1KV V 30KHz Hz BACKLIGHT HALF-LIFT TIME 10,000 HR. z EDGE LED BACKLIGHT COLOR BLUE OR GREEN OR WHITE BACKLIGHT INPUT DC+3.2V V 156 mA BACKLIGHT HALF-LIFT TIME 3,000 (AVOID LIGHTING CONTINUOUSLY) HR. 2. Mechanical Diagram 3. Interface Pin Connections 4. Block And Power Supper Diagram NO SYMBOL LEVEL FUNCTION
1 FGND -- Frame ground
2 V SS -- Ground potential (Logic)
3 V DD -- Power supply for Logic Circuit
4 Vo -- Power supply for LCD Circuit
8 C/D H/L Command/Data
9 V EE -- Negative Voltage (DC-9V ~ -12V)
10 /RST L Controller reset
11 DB0 H/L Data Bit 0
12 DB1 H/L Data Bit 1
13 DB2 H/L Data Bit 2
14 DB3 H/L Data Bit 3
15 DB4 H/L Data Bit 4
16 DB5 H/L Data Bit 5
17 DB6 H/L Data Bit 6
18 DB7 H/L Data Bit 7
19 FS H/L Font select : H:6x8 L:8x8
20 N.C -- --
Ver : A 6/21 5. Environmental absolute maximum ratings ITEM OPERATING STORAGE REMARKS MIN. MAX. MIN. MAX. -- Ambient Temperature -20°C +70 °C -30 °C +80 °C NOTE 1 Humidity NOTE 1 NOTE 2 Without Condensation Vibration -- 4.9m/s 2 -- 19.6m/s 2 XYZ Directions Shock -- 29.4m/s 2 -- 490.0m/s 2 XYZ Directions Remarks: NOTE (1) : Ta at 60 °C : 50 HR Max. NOTE (2) : Ta < 40 °C : 95% RH Max. T a > 4 0 °C : Absolute humidity must be lower than the humidity of 95% at 40 °C. 6. Electrical Characteristics ITEM SYN CONDITION MIN. TYPE MAX. UNIT SUPPLY VOLTAGE FOR LOGIC VDD-VSS -- 4.75 5.0 5.25 V SUPPLY VOLTAGE FOR LCD VDD-VO Ta= 25 ℃ 12.7 13.0 13.3 V INPUT HIGH VOLTAGE VIH VDD = 5V 0.7VDD -- VDD V INPUT LOW VOLTAGE VIL 0.25 0 -- 0.3VDD V SUPPLY CURRENT (LOGIC) IDD VDD=+5V -- -- 15.0 mA IEE V EE = -10V -- -- 5.0 mA 7. Optical Characteristics T a a t 2 5 ℃ ITEM SYM CONDITION MIN. TYPE MAX. UNIT VIEW ANGLE (TOP／BOTTOM) θ1 / θ2 CR ≧5 -- 45/35 -- deg. VIEW ANGLE (LEFT／RIGHT) φ1 / φ2 CR ≧5 -- 35/35 -- deg. CONTRAST RATIO CR -- -- 7 -- ── RESPONSE TIME (RISE) TON ／Tr -- -- 150 -- mS RESPONSE TIME (DECAY) TOFF ／Tf -- -- 200 -- mS 8. Optical Definitions Response Time Contrast Ration View Angle Y(TOP) Y(BOTTOM) X (Left) X (Right) EYEθ2 2 1 Brightness curve of nonselected segment Brightness curve of selected segment Set Point Driving Voltage Btightness Brightness of nonselected segment (B2) Brightness of selected segment (B1) Nonselected Condition Nonselected Condition Btightness Rise Time Fall Time 9. Timing Control ITEM SYMBOL MIN TYP MAX UNIT C/D Set Up Time tCDS 100 -- -- ns C/D Hold Time tCDH 10 -- -- ns /CE,./RD,/WR Pulse Width tCE,tRD,tWR 80 -- -- ns Data Set Up Time tDS 80 -- -- ns Data Hold Time tDH 40 -- -- ns Access Time tACC -- -- 150 ns Output Hold Time tOH -- -- 50 ns
Ver : A 7/21 10. DISPLAY CONTROL INSTRUCTION
10.1 Command list
COMMAND OCDE D1 D2 FUNCTION REGISTER SET 00100001 00100010 00100100 X adrs data Low adrs Y adrs 00H High adrs CURSOR POINTER SET OFFSET REGISTER SET ADDRESS POINTER SET CONTROL WORD SET 01000000 01000001 01000010 01000011 Low adrs Columns Low adrs Columns High adrs 00H High adrs 00H TEXT HOME ADDRESS SET TEXT AREA SET GRAPHIC HOME ADDRESS SET GRAPHIC AREA SET MODE SET 1000X000 1000X001 1000X011 1000X100 10000XXX 10001XXX “OR” mode “EXOR mode “AND” mode “TEXT ATTRIBUTE” mode Internal CG ROM Mode External CG RAM mode DISPLAY MODE 10010000 1001XX10 1001XX11 100101XX 100110XX 100111XX DISPLAY OFF CURSOR ON, BLINK OFF CURSOR ON, BLINK ON TEXT ON, GRAPHIC OFF TEXT OFF, GRAPHIC ON TEXT ON, GRAPHIC ON CURSOR PATTERN SELECT 10100000 10100001 10100010 10100011 10100100 10100101 10100110 10100111
1 LINE CURSOR
2 LINES CURSOR
3 LINES CURSOR
4 LINES CURSOR
5 LINES CURSOR
6 LINES CURSOR
7 LINES CURSOR
8 LINES CURSOR
DATA WRITE AND ADP INCREMENT DATA READ AND ADP INCREMENT DATA WRITE AND ADP DECREMENT DATA READ AND ADP DECREMENT DATA WRITE AND ADP NONVARIABLE DATA READ AND ADP NONVARIABLE SCREENPEEK 11100000 - - SCREEN PEEK SCREEN COPY
11101000 SCREEN COPY
BIT0 (LSB) BIT1 BIT2 BIT3 BIT4 BIT5 BIT6 BIT7 (MSB) Note 1: Status check between all co mmands and data is recommended, though execution time for several commands is specified in above command list. For the commands with “status check” in execution time, execution time does not specified because it is infunced by internal situation of controller LSI. 2: In case of 2 screen mode, Screen copy command cannot be used.
Ver : A 8/21
10.2 Description of command
10.2.1 Register set
00100001 21H CURSOR POINTER SET X address Y address 00100010 22H OFFSET REGISTER SET DATA 00H 00100100 24H ADDRESS POINTER SET LOW address HIGH address A) CURSOR POINTER SET The position of cursor is specified by X ADRS, Y ADRS, The cursor position is moved only by this command. The cursor pointer doesn‘t have the function of increment and decrement. The shifts of cursor are set by this command. X ADRS, Y ADRS are specified following X ADRS 00H~4FH (lower 7bits are valid) Y ADRS 00H~1FH (lower 5bits are valid) 1) 1 screen drive 2) 2 screen drive X ADRS 00~4FH X ADRS 00~4FH B) OFFSET REGISTER SET The offset register is used to determine external character generator RAM area. C) ADDRESS POINT SET The address point set command is used to indicate the start address for writing (or read) to external RAM.
10.2.2 Control word set
01000000 40H TEXT HOME ADDRESS SET Low address High address 01000001 41H TEXT AREA SET Columns 00H 01000010 42H GRAPHIC HOME ADDRESS SET Low address High address 01000011 43H GRAPHIC AREA SET Columns 00H The home address and column size are defined by this command. A) Text home address set The starting address of external display RAM for Text display is defined by this command. The text home address shows the left end and most upper position. The relationship of external display RAM address and display position TH TH + CL TH + TA TH + TA + CL (TH + TA) + TA TH + 2TA + CL (TH + 2TA) + TA TH + 3TA + CL : : TH + (n-1) TA TH + (n-1) TA + CL TH: Text Home address TA: Text Ar ea number (columns) CL: Columns are fi xed by hardware, pin-programmable (EX) Text home address = 0000H Text area = 0020H MD2=H, MD3=H : 32 columns DUAL=H, MDS=L, MDO=L, MD1=H: 4 lines 0000H 0001H 001EH 001FH 0020H 0021H 003EH 003FH 0040H 0041H 005EH 005FH 0060H 0061H 007EH 007FH B) Graphic home address set The starting address of external display RAM for Graphic display is defined by this command. The graphic home address shows th e left end and most upper line. The relationship of external display RAM address and display position GH GH+CL GH+GA CH+GA+CL (GH+GA)+GA GH+2GA+CL (GH+2GA)+GA GH+3GA+CL : : GH+(n-1)GA GH+(n-1)GA+CL GH: Graphic Home address GA: Graphic area number (columns) CL: Columns are fixed by hardware. (pin-programmable) Y ADRS 00H~0FH upper screen Y ADRS 10H~1FH lower screen Y ADRS 00H~0FH
Ver : A 9/21 (EX) Graphic home address = 0000H Graphic area = 0020H M D 2 = H , M D 3 = H : 3 2 c o l u m n s DUAL=H, MDS=L, MD0=M, MD1=H : 2 lines 0000H 0001H 001EH 001FH 0020H 0021H 003EH 003FH 0040H 0041H 005EH 005FH 0060H 0061H 007EH 007FH 0080H 0081H 009EH 009FH 00A0H 00A1H 00BEH 00BFH 00C0H 00C1H 00DEH 00DFH 00E0H 00E1H 00FEH 00FFH 0100H 0101H 011EH 011FH 0120H 0121H 013EH 013FH 0140H 0141H 015EH 015FH 0160H 0161H 017EH 017FH 01A0H 01A1H 01BEH 01BFH 01C0H 01C1H 01DEH 01DFH 01E0H 01E1H 01FEH 01FFH C) Text area set The columns of display are defined by the hardware setting. This command can be used to adjust columns of display. (EX) LCD size: 20 columns, 4 lines Text home address = 0000H Text area = 0014H M D 2 = H , M D 3 = H : 3 2 c o l u m n s DUAL=h, MDS=L, MD0=L, MD1=H :4 lines L C D D) Graphic area set The columns of display are defined by the hardware setting. Th is command can be used to adjust columns of graphic display. (EX) LCD size: 20 columns, 2 lines Text home address = 0000H Text area = 0014H M D 2 = H , M D 3 = H : 3 2 c o l u m n s DUAL=H, MDS=L, MD0=H, MD1=H : 2 lines LCD The address in graphic area can be continuous and RAM area can be used without ineffective area, if graphic area is defined the same number as the actual column number of LCD display.
10.2.3 Mode set
1000X000 “OR” mode 1000X001 “EXOR” mode 1000X011 “AND” mode 1000X100 “TEXT ATTRIBUTE” mode
10000 XXX internal character generator mode
10001 XXX external character generator mode
The display mode is defined by this command. The display mode doesn‘t change until this command is sent. Logically “OR”, “EXOR”, “AND” of text and graphic display can be displayed. When internal character generator mode is selected, character code 00H~7FH are selected from built-in character generator RM. The character code 80H~FFH are automatically selected from external character generator RAM.
Ver : A 10/21 G r a p h i c T e x t Note: Only text display is attributed, because attribute data is located in graphic RAM area. A) Attribute function “Reverse display”, “Character blink” and “Inhibit” are called “Attribute”. The attribute data is written in the graphic area defined by Control word set command. The mode set command selects text display only and graphic display cannot be displayed. The attribute data of the 1st character in text area is written at the 1st 1 byte in graphic area, and attribute data of n-th character is written at the n-th 1 byte in graphic area. Attribute function is defined as follows: Attribute RAM 1 Byte X X X X d3 d2 d1 d0 d3 d2 d1 d0 FUNCTION 0 0 0 0 normal display 0 1 0 1 reverse display 0 0 1 1 inhibit display 1 0 0 0 blink of normal display 1 1 0 1 blink of reverse display 1 0 1 1 blink of inhibit display X: don‘t care
10.2.4 Display mode
1001XX10 cursor on, blink off 1001XX11 cursor on, blink on 100101XX text on, graphic off 100110XX text off, graphic on 100111XX text on, graphic on 1 0 0 1 d3 d2 d1 d0 cursor blink on: 1, off: 0 cursor display on: 1, off: 0 text display on: 1, off: 0 graphics display on: 1, off: 0 Note: It is necessary to turn on “text” display“ and ”graphic display“ in following case. 1) Combination of text/graphic display 2) Attribute function
10.2.5 Cursor pattern select
CODE FUNCTION CODE FUNCTION 10100000 1 line cursor 10100100 5 lines cursor 10100001 2 lines cursor 10100101 6 lines cursor 10100010 3 lines cursor 10100110 7 lines cursor 10100011 4 lines cursor 10100111 8 lines cursor When cursor display is ON, this command selects the cursor pattern from 1 line to 8 lines. The cursor address is defined by cursor pointer set command. 1 line cursor 2 lines cursor 8 lines cursor
Ver : A 11/21
10.2.6 Data auto read/write CODE FUNCTION
10110000 B0H data auto write set
10110001 B1H data auto read set
10110010 B2H auto reset
This command is convenient to send full screen data from external display RAM. After setting auto mode, “data write (or read)” command is not necessary between each data. “Data auto write (or read)” command should follow the “Address pointer set” and address pointer is automatically increment by +1 after each data “auto reset” is necessary to return normal operation because all data is regarded “display data” and no command can be accepted in the auto mode. Note: Status check for auto mode (STA2, STA3 should be checked between each data. Auto reset should be performed after checking STA3=1 (STA2=1)). Refer following flow chart.
10.2.7 Data read write
11000000 C0H DATA WRITE AND ADP INCREMENT data
11000001 C1H DATA READ AND ADP INCREMENT -
11000010 C2H DATA WRITE AND ADP DECREMENT data
11000011 C3H DATA READ AND ADP DECREMENT -
11000100 C4H DATA WRITE AND ADP NONVARIABLE data
11000101 C5H DATA READ AND ADP NONVARIABLE -
This command is used for data write from MPU to external display RAM to MPU. Data write/read should be executed after setting address by address pointer can be automatically increment or decrement by setting this command. Note: This command is necessary for each 1 byte data. Refer following flow chart.
10.2.8 Screen peek
11100000 E0H screen peek -
This command is used to transfer displayed 1 byte data to data stack, and this 1 byte data can be read from MPU by data access. The logical combination data of text and graphic display on LCD screen can be read by this command. The status (STA6) should be checked just after “screen peek” command. If the address command is not in graphic area, this command ignored and status flag (STA6) is set. Refer following flow chart.
Ver : A 12/21
10.2.9 Screen copy
11101000 E8H screen copy -
This command is used to copy displayed 1 line data to graphic area. The start point of 1 line data in the screen is determined by the address pointer. Note: a) When the attribute of text is used this command cannot be used. (Because attribute data is in the graphic area.) b) In case of 2 screen drive, this command cannot be used. (Because T6963c cannot separate upper screen data and lower screen data.) Refer following flow chart.
10.2.10 Bit set/reset
CODE FUNCTION CODE FUNCTION
11110 XXX bit reset 1111X011 bit 3
11111 XXX bit set 1111X100 bit 4
1111X000 bit 0 (LSB) 1111X101 bit 5 1111X001 bit 1 1111X110 bit 6 1111X010 bit 2 1111X111 bit 7 This command is used to set or reset a bit of 1 byte is specified by address pointer. Plural bits in the 1 byte data cannot be set/reset at a time. Refer following flow chart.
10.3 Flowchart of communications with MPU
10.3.1 Status Read
Before sending data (read/write), command it is necessary to check the status. A) Status Check Status of T6963C can be read from data lines. RD= L,WR = H, CE = L,C/D = H,D0~7 -> Status word T6963C. Status word format is following. MSB LSB STA7 STA6 STA5 STA4 STA3 STA2 STA1 STA0 D7 D6 D5 D4 D3 D2 D1 D0 STA0 check capability of command execution 0: disable 1:enable STA1 check capability of data read/write 0: disable 1:enable STA2 check capability of auto mode data read 0: disable 1:enable STA3 check capability of auto mode data write 0: disable 1:enable STA4 not use STA5 check capability of controller operation 0: disable 1:enable STA6 error flag. using screen peek/copy command 0: no error STA7 check the condition blink 0: display off 1:normal display Note: 1. It is necessary to check STA0 and STA1 at the same time. The error is happened by sending data at executing command. 2. The status check will be enough to check STA0/STA1. 3. The STA2/STA3 are valid in auto mode STA0/STA1 are invalid. Status checking flow 4. It is impossible to save status check in the case of command that is MSB 0. To have the delay time cannot be save status check. The interrupt of hardware is happened at the end of lines. If command of MSB0 is sent in this period, the command executing is waited. The state of waiting is not known without to check status. The sending next command or data is disregarded or rewrites data of waiting command
Ver : A 13/21
10.3.2 Data Set
In T6963C, the data have been set and command executes. The order of procedure of command sending 1) The case of 1 data 2) The case of 2 data Note: In case of over 2 data sending, the la st data ( or last 2 data) is valid.
10.4 Initialize
Initialize of controller LSI T6963C is required for “Mode set”, “Control word set” after power on. Following is the one example of initialize procedure of 240x64 dots display (In case of 6x8 dots/font). Power on Power on Hard reset ( use reset terminal ) RES ET=“L” ( 1msec minimum after VDD>4.75V ) Mode set 1 1 0 0 0 0 0 0 0 “OR” mode Control word set Graphic home position set ( Graphic home position 000H ) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 graphic home address command Number of graphic area set ( Graphic 40x6 dots ) 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 1 number of area command Text home position set ( Text home position 1000H ) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 0 text home address command Number of text area set ( text 40 column ) 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 1 number of area command Initialize end , Data Write Address pointer set ( address pointer 0000H ) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0 graphic home address command Data Write ( graphic ) x 0 1 0 1 0 1 0 1 1 1 1 0 0 0 0 0 1 0 1 0 1 0 1 0 1 1 1 0 0 0 0 0 x x x x x x x x Data command Data command Address pointer set ( address pointer 1000H ) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 1 0 0 text home address command Data write ( text ) x 0 0 1 1 0 1 0 0 1 1 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 0 0 0 0 0 0 x x x x x x x x Data command Data command Display Mode Set ( text/graphic on ) 1 1 0 0 1 1 1 0 0 Note 1: “status check” should be inserted between all command and data. 2: Display mode set register is cleared ( no display mode ) by the hard reset , and no display is appeared on LCD panel. And just after “Display Mode set 9CH”, written data is display on the LCD. 11. CG ROM PATTERN
Ver : A 14/21 12. Reliability Condition TN Type STN/FSTN Type Normal Temp. Wide Temp. Normal Temp. Wide Temp. Horizontal (Φ1/Φ2) ±30° ±30° ±40° ±40° Viewing Angle Vertical (Θ2/Θ1) 15 °to 35° 15 °to 35° 35 °to 55° 35 °to 55° Operating Temperature 0 to 50℃ -20 to 70 ℃ 0 to 50 ℃ *-20 to 70℃ Storage Temperature -10 to 60℃ -30 to 80 ℃ -10 to 60 ℃ *-30 to 80℃ High Temperature (Power Off) 240 Hours @60℃
240 Hours
@80℃ @60℃ @80℃ Low Temperature (Power Off) 240 Hours @-10℃ @-30℃ @-10℃ @-30℃ High Temperature (Power On) 240 Hours @50℃ @70℃ @50℃ @70℃ Low Temperature (Power On) 240 Hours @0℃ @-20℃ @0℃ @-20℃ High Temperature & High Humidity (Power Off) 40℃/90%RH 40℃/90%RH 40℃/90%RH 40℃/90%RH A 60min@0℃ 60min@-20 ℃ 60min@0℃ 60min@-20 ℃ B 5min@25℃ 5min@25 ℃ 5min@25 ℃ 5min@25 ℃ T h e r m a l S h o c k C
5 C y c l e B
A C 60min@50℃ 60min@70 ℃ 60min@50 ℃ 60min@70 ℃ LCD Lift (25℃/ 45%RH) 50,000 Hours 50,000 Hours 50,000 Hours 50,000 Hours *Wide temp. version may not available for some products, Please consult our sales engineer or representative. 13. Functional Test & Inspection Criteria
13.1 Sample plan
Sample plan according to MIL-STD-105D level 2, and acceptance/rejection criteria is. Base on : Major defect : AQL 0.65 Minor defect : AQL 2.5
13.2 Inspection condition
Viewing distance for cosmetic inspection is 30cm with bare eyes, and under an environment of 800 lus (20W) light intensity. All direction for inspecting the sample should be within 45°against perpendicular line.
13.3 Definition of Inspection Zone in LCD
Zone A : Character / Digit area Zone B : Viewing area except Zone A ( Zone A + Zone B = minimum Viewing area ) Zone C : Outside viewing area ( invisible area after assembly in customer’s product ) Note : As a general rule, visual defects in Zone C are permissible, when it is no trouble for quality and assembly of customer’s product.
13.4 Major Defect
All functional defects such as open ( or missing segment ), short, contrast differential, excess power consumption, smearing, leakage, etc. and overall outline dimension beyond the drawing. Are classified as major defects. C B A
Ver : A 15/21
13.5 Inspection Parameters And Glass Pixel(偏光板和玻璃圖像檢驗)
NO Polarizer(偏光板) Criteria
1 Black or White spots And
(黑/白點和刺孔) D/ 面積=(Length/長度+Width/寬度)/2 => * ：Disregard(忽略) Dimension (面積) Acceptable number (可接受數量) D＜0.15 * 0.15≦D≦0.2 4 0.2≦D≦0.25 2 D≦0.3 0
2 Scratch
(刮傷) * 0.04≧W * 3.0≧L 0.06 ≧W 4 2.0≧L 0.08 ≧W 2 － 0.1 ≧W 0 X：Length(長度) Y ：Width(寬度) * ：Disregard(忽略) X(mm) Y(mm) Acceptable number (可接受數量)
3 Air Bubbles
(between glass & polarizer) 氣泡(玻璃跟偏光板之間) D≦0.15 * 0.15＜D≦0.25 2 0.25＜D 0 *：Disregard ( 忽略) Dimension (面積) Acceptable number (可接受數量)
Ver : A 16/21 Glass of Pixel (玻璃的圖像) (1)Pixel shape (with Dent) /圖像凹度 Less than 0.152 mm is no counted ( 小於 0.152mm 者不計) (2)Pixel shape (with Projection)/圖像凹度 Should not be connected next pixel (點與點間不可先連接) (3)Deformation/變形
- Less than 0.1 mm is no counted ( 小於 0.15mm 者不計) (4) Deformation/變形 Less than 0.3 mm is no counted ( 小於 0.3mm 者不計)
Ver : A 17/21 14. Test (測試條件) – Normal Temperature (常溫) No change no display and in operation under the following text condition. (在不改變原先顯示下進行以下測試操作) Conditions ： Unless otherwise specified, test will be conducted under the following condition. T e m p e r a t u r e ： 20 ±5 ℃ H u m i d i t y ： 40 ±5%RH Tests will be not conducted under functioning state. (條件：除非其他特殊情況，否則測試將以溫度：20±5 ℃，濕度：40±5%RH 為主) NO Parameter Conditions Notes
1 High Temperature
50℃±2 ℃ , 96 hrs (operation state) (96 小時，溫度50℃±2 ℃電源開啟的操作情況下)
2 Low Temperature
0℃±2 ℃ , 96 hrs (operation state) (96 小時，溫度0℃±2 ℃電源開啟的操作情況下)
3 High Temperature
60℃±2 ℃ , 96 hrs (96 小時，溫度60℃±2 ℃電源關閉靜態操作下)
4 Low Temperature
-10℃±2 ℃ , 96 hrs (96 小時，溫度-10℃±2 ℃電源關閉靜態操作下) 1 , 2
5 Damp Proof
電源關閉靜態操作下) 1 , 2 Vibration Test Total fixed amplitude ： 1.5 mm ( 完全固定輻射：1.5mm) Vibration Frequency ： 10 ～ 55 Hz ( 震動頻率：10~55 Hz) One cycle 60 seconds to 3 directions of X , Y , Z for each 15 minutes (每一個循環 X ，Y，Z 軸方向各做 60 秒，連續 做 5 次，共計 15 分鐘)
7 Shock Test To be measured after dropping from 60cm high on the concrete
surface in packing state. (包裝材從 60 公分高的地方向地面落下) Dropping method comer dropping (角落落下方式) A comer：once Edge dropping (側邊落下) B , C , D edge : once Face dropping (表面落下) E , F , G face : once Note 1：No dew condensation to be observed. (不要在＂水氣凝結點＂下觀察) Note 2：The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after removed from the test chamber (從實驗室移出後，放在一般常溫 ( 溫度：25℃，濕度：45%RH)， 且四小時後通電流或電壓，看它是否能正常動作) Note 3：Vibration test will be conducted to the product itself without putting it in a container. ( 在震動測試下，產品本身不需容器即能自行傳導)
Ver : A 18/21 15. Test (測試條件) – Wide Temperature (廣溫) No change no display and in operation under the following text condition. (在不改變原先顯示下進行以下測試操作) Conditions ： Unless otherwise specified, test will be conducted under the following condition. T e m p e r a t u r e ： 20 ±5 ℃ H u m i d i t y ： 40 ±5%RH Tests will be not conducted under functioning state. (條件：除非其他特殊情況，否則測試將以溫度：20±5 ℃，濕度：40±5%RH 為主) NO Parameter Conditions Notes 70℃±2 ℃ , 96 hrs (operation state) (96 小時，溫度 70℃±2 ℃電源開啟的操作情況下) -20℃±2 ℃ , 96 hrs (operation state) (96 小時，溫度-20℃±2 ℃電源開啟的操作情況下) 80℃±2 ℃ , 96 hrs (96 小時，溫度80℃±2 ℃電源關閉靜態操作下) -30℃±2 ℃ , 96 hrs (96 小時，溫度-30℃±2 ℃電源關閉靜態操作下) 1 , 2 電源關閉靜態操作下) 1 , 2 Vibration Test Total fixed amplitude ： 1.5 mm ( 完全固定輻射：1.5mm) Vibration Frequency ： 10 ～ 55 Hz ( 震動頻率：10~55 Hz) One cycle 60 seconds to 3 directions of X , Y , Z for each 15 minutes (每一個循環 X ，Y，Z 軸方向各做 60 秒，連續 做 5 次，共計 15 分鐘) surface in packing state. (包裝材從 60 公分高的地方向地面落下) Dropping method comer dropping (角落落下方式) A comer：once Edge dropping (側邊落下) B , C , D edge : once Face dropping (表面落下) E , F , G face : once Note 1：No dew condensation to be observed. (不要在＂水氣凝結點＂下觀察) Note 2：The function test shall be conducted after 4 hours storage at the normal Temperature and humidity after removed from the test chamber (從實驗室移出後，放在一般常溫 ( 溫度：25℃，濕度：45%RH)， 且四小時後通電流或電壓，看它是否能正常動作) Note 3：Vibration test will be conducted to the product itself without putting it in a container. ( 在震動測試下，產品本身不需容器即能自行傳導)
Ver : A 19/21 16. Precautions Against Product Handling [產品使用注意事項]： The following precautions will guide you in handling our product correctly. [下列警戒引導正確地使用產品] 16.1 Care of the LCD module against static electricity discharge. [LCD 模組靜電注意事項]
16.1.1 When working with the module, be sure to ground your body and any electrical
equipment you may be using. We strongly recommend the use of anti static mats (made of rubber), to protect work tables against the hazards of electrical shock. [ 操作模組時，避免操作者身體接地及任何造成靜電的設備同時使用，強烈建議(橡膠製) 抗靜電墊的使用，以免工作台面遭受到電氣干擾]
16.1.2 Slowly and carefully remove the protective film from the LCD module, since this operation
can generate static electricity. [ 緩慢小心地移除 LCD 模組上的保護膜，以防靜電產生] 16.1.3 Avoid the use of work clothing made of synt hetic fibers. We recommend cotton clothing or other conductivity-treated fibers. [ 避免穿著人造合成的工作服，建議棉質或是有傳導性的纖維質料]
16.2 Liquid crystal display devices (LCD devices) [液晶螢幕顯示器的組成]
16.2.1 The polarizer adhering to the surface of the LCD is made of a soft material. Guard against scratching it. [ 偏光板是軟性原料製成，請勿刮傷] 16.2.2 The LCD device panel used in the LCM is made of plate glass. Avoid any strong mechanical shock. Should the glass break handle it with care. [ 模組使用的玻璃為平面玻璃，避免任何強烈的機械撞擊，且觸碰時請小心]
16.3 When the LCD module alone must be stored form long periods of time
[當 LCD 模組須長時間存放時] 16.3.1 Protect the modules from excessive external forces. [避免外力壓迫] 16.3.2 Protect the modules from high temperature and humidity. [ 避免處於高溫高濕下] 16.3.3 Keep the modules out of direct sunlight or direct exposure to ultraviolet rays. [ 遠離陽光曝曬或直接曝露在紫外線下]
16.4 Use the module with a power supply that is equipped with an overcurrent protector circuit, since the
module is not provided with this protective feature. [ 因為模組本身沒有防護，所以模組的供應器應配有過高電流的保護迴路] 16.5 Do not ingest the LCD fluid itself should it leak out of a damaged LCD module. Should hands or clothing come in contact with LCD fluid, wash immediately with soap. [LCD 破裂液晶外漏時，切勿食下液晶；若手或衣服接觸到液晶，請立刻用肥皂清洗]
16.6 Conductivity is not guaranteed for models that use metal holders where solder connections between
the metal holder and the PCB are not used. Please cont act us to discuss appropriate ways to assure conductivity. [當金屬框並沒焊接於 PCB 板上時，無法保證使用金屬框是具有傳導性，請連絡我們商討適當 方式傳導]
16.7 For models which use CCFL [CCFL 的模組]:
16.7.1 High voltage of 1000V or greater is applied to the CCFL cable connector area. [CCFL 排線連接器用於 1000V 以上的高電壓]
16.7.2 Protect CCFL cables from rubbing against the unit and thus causing the wire jacket to become
worn. [CCFL 排線必須有保護 CCFL 與模組磨擦，以防 CCFL 外殼受到損害]
16.7.3 The use of CCFLs for extended periods of time at low temperatures will significantly shorten
their service life. [長時間低溫使用 CCFL 會明顯縮減其使用壽命]
Ver : A 20/21
16.8 For models which use touch panels [觸控式面板模組]:
16.8.1 Do not stack up modules since they can be damaged by components on neighboring modules. [ 勿堆疊模組以防損壞] 16.8.2 Do not place heavy objects on top of the product. This could cause glass breakage. [勿將重物放置在產品上，會導致玻璃破損]
16.9 For models which use COG & TAB [COG 及 TAB 模組]:
16.9.1 The mechanical strength of the product is low si nce the IC chip is faces out unprotected from
the rear. Be sure to protect the rear of the IC chip from external forces. [ 由於 IC 晶片表面無防護，所以抗壓力有限，須加強保護以防外力]
16.9.2 Given the fact that the rear of the IC chip is le ft exposed, in order to protect the unit from
electrical damage, avoid installation configurations in which the rear of the IC chip runs the risk of making any electrical contact. [ 勿暴露 IC 晶片以防電氣干擾，且避免安裝IC 時有任何電子接觸]
16.10 Models which use flexible cable, heat seal, or TAB [加有軟排線、熱封條或 TAB 的模組]:
16.10.1 In order to maintain reliability, do not touch or hold by the connector area. [ 以維持產品信賴度，請勿觸碰或握住連接器]
16.10.2 Avoid any bending, pulling, or other excessive force, which can result in broken
connections. [避免彎曲、拉扯或過度力量，會造成連接器損壞]
16.11 In case of acrylic plate is attached to front si de of LCD panel, cloudiness (very small cracks) can
occur on acrylic plate, being influenced by some components generated from polarizer film. Please check and evaluate those acrylic materials carefully before use. [貼在 LCD 玻璃前面的壓克力板若有模糊情況(微小裂縫)，即會影響偏光板；使用前請仔細確 認壓克力材質]
16.12 In case of buffer material such as cushion/gask et is assembled into LCD module, it may have an
adverse effect on connecting parts (LCD pa nel-TCP/ HEAT SEAL/ FPC, PCB-TCP/HEAT SEAL/FPC, TCP-HEAT SEAL, TCP-FPC, HEAT SEAL-FPC) depending on its materials. Please check and evaluate these materials carefully before use. [ 緩衝原料像是減震墊 / 襯墊，或許會對連接器 (LCD panel-TCP/ HEAT SEAL/ FPC, PCB-TCP/HEAT SEAL/FPC, TCP-HEAT SEAL, TCP-FPC, HEAT SEAL-FPC)造成反效果，使用 前請仔細確認材料] 17. Warranty [保證]： This product has been manufactured to your company’s specifications as a part for use in your company’s general electronic products. It is guaranteed to perfor m according to delivery specifications. For any other use apart from general electronic equipment, we ca nnot take responsibility if the product is used in medical devices, nuclear power control equipment, aeros pace equipment, fire and security systems, or any other applications in which there is a direct risk to human life and where extremely high levels of reliability are required. If the product is to be used in any of the above applications, we will need to enter into a separate product liability agreement. [此產品的製造是依照客戶的規格，被使用於客戶的一般電子產品上，保證產品製作根據出貨的規 格，若產品的使用不是在一般電子設備，而組裝於下列產品上則無法受理（如醫療產品、核心電源 控制設備、航空設備、防火及保全系統，或任何相關儀器會直接影響人類生命等），若模組使用於 上述的儀器，則需商討各別產品責任義務的協定]
Ver : A 21/21
17.1 We cannot accept responsibility for any defect, whic h may arise after the application of strong
external force to the product. [ 不受理因強大外力衝擊造成產品的缺陷]
17.2 We cannot accept responsibility for any defect, which may arise from additional manufacturing of the
product (including disassembly and reassembly), after product delivery. [ 不受理產品出貨後，因額外加工(包含拆裝及重新封包)造成的缺陷]
17.3 We cannot accept responsibility for any defect, whic h may arise due to the application of static
electricity after the product, has passed your company’s acceptance inspection procedures. [ 不受理通過貴公司檢驗流程後，由於靜電造成產品的缺陷] 17.4 We cannot accept responsibility for intellectual property of a third party, which may arise through the application of our product to your assembly with ex ception to those issues relating directly to the structure or method of manufacturing of our product. [不受理因在客戶產品生產線端所產生的第三人智慧財產權責任，除非與我司生產製造方法有直 接關係的問題]
17.5 When the product is in CCFL models, CCFL servi ce life and brightness will vary according to the
performance of the inverter used, leaks, etc. We cannot accept responsibility for product performance, reliability, or defect, which may arise. [ 產品是 CCFL 模組時，CCFL 的壽命及亮度將取決於連接器的性能、漏電量等；無法受理因 CCFL 造成產品性能的缺陷]
17.6 ILLUMINANT will not be held responsible for any quality guarantee issue for defect products
longer than 1(one) year from ILLUMINANT production which ever comes later. [ 出廠超過一年的瑕疵品，任何品質擔保則不受理]