IAM-93516 HP | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

Features

RF = -10 dBm;

  • •••• LO =1.7 GHz, PinLO = 0 dBm;
  • •••• IF = 210 MHz unless otherwise specified
  • •••• High Linearity: 23.1 dBm IIP3(typ)
  • •••• Conversion Gain: 9.4 dB typical
  • •••• Low Noise Figure: 11.6 dB
  • •••• Wide band operation:
  • •••• 400-3000 MHz RF & LO input
  • •••• Fully differential or single ended operation
  • •••• High P1dB: 19.3 dB typical
  • •••• Consistent RF performance over LO Power
  • •••• Low current consumption: 5V@ 111mA typical
  • •••• Excellent uniformity in product specifications
  • •••• 3mm x 3mm x 0.9mm LPCC package
  • •••• MSL-1 and Lead-free. The amplifier output port is 200 ohm matched and fully differential. The simple matching at the RF port provides for optimum input return loss, noise figure and IIP3 performance. The IAM-93516 is ideally suited for frequency down conversion for base station radio card receiver, microwave link receiver, MMDS, modulation and demodulation for receiver and general purpose resistive FET mixer, which require high linearity. All devices are 100% RF and DC tested.

Applications

  • •••• Frequency down converter for base station radio card, microwave link transceiver, and MMDS
  • •••• Modulation and demodulation for receiver
  • •••• General purpose resistive FET mixer for other high linearity

1.0 Absolute Maximum Ratings [1]

2.0 Product Consistency Distribution Charts [5,6]

  1. Operation of this device above any one of these parameters may cause permanent damage.
  2. Determined at DC quiescent conditions and T A = 25°C.
  3. Board (package belly) temperature T B is 25°C. Derate 25 mW/°C for T B > 130 °C.
  4. Channel-to-board thermal resistance measured using Infra Red Imaging Method and 150 o C Liquid Crystal Measurement method.
  1. Distribution data sample size is 510 samples taken from 3 different wafers lots. Future wafers allocated to this product may have nominal values

anywhere between the upper and lower limits.

  1. Measurements were made on a production test board, which represents a trade-off between optimal Gain, IIP3, NF, P1dB and isol ation. Board losses

parameter file is also compensated. The total IF amplifier output loss is 0.67dB.

  1. The device current is measured without LO signal. At LO=0dBm, the current reduces by around 6 to 7mA.
  2. Gain, P1dB, isolation and return loss test conditions: F RF =1.91GHz, FLO = 1.7GHz, FIF = 210MHz, PinRF = -10dBm, PinLO = 0dBm.

IIP3 test condition: F RF1 = 1.91GHz, FRF2 = 1.89GHz, FLO = 1.7GHz, PinRF = -10dBm, PinLO = 0dBm.

3.0 IAM-93516 Electrical Specifications [6,8]

4.0 IAM-93516 Typical Performance [9,10]

Figure 4. IAM-93516 demoboard schematic optimally tuned at F RF = 1.91GHz and FLO = 1.7GHz Symbol Parameter and Test Condition Units Min. Typ. Max.

5.0 IAM-93516 Typical Harmonic Suppresion Table [12,13]

6.0 IAM-93516 Pin Description

Figure 21. Harmonic Suppresion Table 5 VDD1 DC Power supply for the mixer circuit. differential or single ended. 14 VDD2 DC Power supply for the IF amplifier circuit.

  1. The harmonic suppression table shows the spurious signals present due to the mixing of the RF and LO at down conversion mode .

d. LO Harmonics are referenced to the signal level of the LO signal at 1.7GHz at the IF amplifier output.

PCB layout and Stencil Design LPCC 3x3 Package Dimensions Bottom ViewTop View Side View A3A1 A E D E D k eINDEX AREA (D/2 X E/2) SEATING PLANE e DIMENSIONS ARE IN MILLIMETERS 1GL 3X3-0.50 MIN. 0.80 2.90 1.70 2.90 1.70 0.20 NOM. 0.90 3.00 1.80 3.00 1.80 0.50 BSC. 0.02 0.20 REF. MAX. 1.00 3.10 1.90 3.10 1.90 0.05 REF. A D E e k PACKAGE

0.3±0.05 3.3±0.1 1.55±0.1 1.6±0.1 R 0.3 Typical 1.55±0.05 2.0±0.1 [1] 4.0±0.1 [2] 1.75±0.1 5.5±0.1[1] 12.0±0.3 3.3±0.18.0±0.1 Note: I. Measured from centerline of sprocket hole to centerline of pocket. II. Cumulative tolerance of 10 sprocket hole is ± 0.20 . III. Measured from centerline of sprocket hole to centerline of pocket. IV. Other material available. V. All dimension in millimeter unless otherwise stated.

www.agilent.com/ semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (408) 654-8675 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6756 2394 India, Australia, New Zealand: (+65) 6755 1939 Japan: (+81 3) 3335-8152(Domestic/Inter- national), or 0120-61-1280(Domestic Only) Korea: (+65) 6755 1989 Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843 Data subject to change. Copyright © 2005 Agilent Technologies, Inc. May 9, 2005 5989-2800EN Part Number No. Of Devices Container IAM-93516-TR1 1000 7" Reel IAM-93516-TR2 5000 13" Reel IAM-93516-BLK 100 Antistatic Bag Part Number Ordering Information