DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

PN 617677 September 1996 Rev. 3, 8/20 ©1996-2020 Fluke Corporation. All rights reserved. Specifications are subject to change without notification. All product names are trademarks of their respective companies. Fluke Corporation P.O. Box 9090 Everett, WA 98206-9090 U.S.A. Fluke Europe B.V. P.O. Box 1186

5602 BD Eindhoven

Go to www.fluke.com to register your Product and find more information. Safety A Warning identifies conditions and procedures that are dangerous to the user. A Caution identifies conditions and procedures that can cause damage to the Product or the equipment under test. XW Warning To prevent possible electrical shock, fire, or personal injury:

  • Carefully read all instructions.
  • Read all safety information before you use the Product.
  • Do not alter the Product and use only as specified, or the protection supplied by the Product can be compromised.
  • Do not use the Product around explosive gas, vapor, or in damp or wet environments.
  • Do not use the Product if it operates incorrectly.
  • Use Product-approved measurement category (CAT), voltage, and amperage rated accessories (probes, test leads, and adapters) for all measurements.
  • Do not exceed the Measurement Category (CAT) rating of the lowest rated individual component of a Product, probe, or accessory.
  • Comply with local and national safety codes. Use personal protective equipment (approved rubber gloves, face protection, and flame-resistant clothes) to prevent shock and arc blast injury where hazardous live conductors are exposed.
  • Before each use, examine the Product. Look for cracks or missing pieces of the clamp housing or output cable insulation. Also look for loose or weakened components. Carefully examine the insulation around the jaws.
  • Do not use test leads if they are damaged. Examine the test leads for damaged insulation and measure a known voltage.
  • Do not touch voltages >30 V ac rms, 42 V ac peak, or 60 V dc.
  • Do not apply more than the rated voltage, between the terminals or between each terminal and earth ground.
  • Do not use a current measurement as an indication that a circuit is safe to touch. A voltage measurement is necessary to know if a circuit is hazardous.
  • Limit operation to the specified measurement category, voltage, or amperage ratings.
  • The battery door must be closed and locked before you operate the Product.
  • Remove all probes, test leads, and accessories before the battery door is opened.
  • Hold the Product behind the tactile barrier.
  • Remove the input signals before you clean the Product.
  • Repair the Product before use if th e battery leaks. Battery leakage may create a shock hazard or damage the Product.
  • Use only specified replacement parts.
  • Have an approved technician repair the Product.
  • Remove the batteries if the Product is not used for an extended period of time, or if stored in temperatures above 50 °C. If the batteries are not removed, battery leakage may result.
  • Batteries contain hazardous chemicals that can cause burns or explode. If exposure to chemicals occurs, clean with water and get medical aid.
  • Do not put battery cells and battery packs near heat or fire. Do not put in sunlight. Symbols Symbol Description X WARNING. HAZARDOUS VOLTAGE. Risk of electric shock. W WARNING. RISK OF DANGER.  Consult user documentation.  AC (Alternating Current)  DC (Direct Current) T Double Insulated  Earth , Application around and removal from uninsulated hazardous live conductors is permitted. Conforms to European Union directives. ) Certified by CSA Group to North American safety standards.  Conforms to relevant Australian Safety and EMC standards. Measurement Category III is applicable to test and measuring circuits connected to the distribution part of the building’s low- voltage MAINS installation. This product complies with the WEEE Directive marking requirements. The affixed label indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE Directive Annex I, this product is classed as category 9 "Monitoring and Control Instrumentation" product. Do not dispose of this product as unsorted municipal waste. P

See Table 1 for a list of features and connections. See Table 2 for instructions on how to make a dc current measurement. Table 1. Features and Connections

  • Accepts safety-shrouded banana plugs
  • Can display 1 mV (0.1 mV preferred)
  • Accuracy ≥0.75 %
  • Input impedance 1 M Ω, ≤100 pF

Table 2. DC Current Measurement

76 TRUE RMS MULTIMETER

See Table 3 or instructions on how to make an ac current measurement. To test the battery, see Table 4. Table 3. AC Current Measurement Table 4. Battery Test

For specified battery life, use an alkaline battery. To replace the battery, see Figure 1. Figure 1. Battery Replacement During long periods of non-use (>60 days), remove and store the battery separately. service information, contact your nearest Fluke dealer or service center.

With a true-rms voltmeter, the minimum ac current is limited to the low end of the specified mV ac range. Usable Current Range DC Accuracy (zero adjusted, conductor centered) AC Accuracy Crest Factor ≤3 (0 A to 400 A) Crest Factor ≤3 (0 A to 600 A) Bandwidth Temperature 28 °C to 50 °C) IEC 61010-2-032: CAT III 600 V Electromagnetic Compatibility (EMC) Environment, IEC 61326-2-2 CISPR 11: Group 1, Class A, Group 1: Equipment has intentionally generated and/or uses conductively- coupled radio frequency energy that is necessary for the internal function of the equipment itself. Class A: Equipment is suitable for use in all establishments other than domestic and those directly connected to a low-voltage power supply network that supplies buildings used for domestic purposes. There may be potential difficulties in ensuring electromagnetic compatibility in other environments due to conducted and radiated disturbances. Caution: This equipment is not intended for use in residential environments and may not provide adequate protection to radio reception in such environments. Communications Equipment) Class A: Equipment meets requirements for industrial electromagnetic wave equipment and the seller or user should take notice of it. This equipment is intended for use in business environments and not to be used in homes. exempt device per clause 15.103.

LIMITED WARRANTY AND LIMITATION OF LIABILITY This Fluke product will be free from defects in material and workmanship for one year from the date of purchase. This warranty does not cover fuses, disposable batteries, or damage from accident, neglect, misuse, alteration, contamination, or abnormal conditions of operation or handling. Resellers are not authorized to extend any other warranty on Fluke’s behalf. To obtain service during the warranty period, contact your nearest Fluke authorized service center to obtain return authorization information, then send the product to that Service Center with a description of the problem. THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY. Since some states or countries do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of liability may not apply to you.