DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 18
Technical content
Features
RoHS compliant for all six substances High density front-ends 15.2 to 18.3 W/in3 Wide input voltage range 85 to 264 VAC 12 V standby voltage, 1A per front-end Highly efficient topology reduces operating costs I2C interface status and control I2C voltage and current limit setting Analog output voltage setting Overtemperature, output overvoltage, and output overcurrent protection ORing circuits for true redundant operation: V o1: ORing FETs; Vo2: ORing Diodes Status LEDs: AC OK, DC OK, and Fan Fail/Overtemperature Fail
Applications
Telecommunications Data communications Servers Distributed power
Description
The FNP1500/1800 front-ends are power-factor-corrected (PFC) which (depending on model type) provide a 12 VDC or 48 VDC (1500 or 1800 watt) output, and can be used in hot-swap redundant systems. Their very small dime nsions allow configuration of up to three units in a 1U rack. The FNP front-ends have a front -mounted AC receptacle. The highly efficient thermal design with internal-fan cooling permits their use over wide temperature ranges and provides very high reliability. Status information is provided with front panel LEDs, logic signals, and via an I 2C management interface. In addition, the I 2C bus can enable the power supply, set high fan speed, adjust the output voltage, and set the output current limit. The FNP1500/1800's meet international safety standards and display the CE-Mark for the European Low Voltage Directive (LVD). FNR-3-12G and FNR-3-48G power-shelf solutions provide rectif ication, system management, and power distribution, while maintaining high reliability and offering flexibility for future expansion. The power shelves can be configured with up to thre e hot- swappable 1500 or 1800-watt AC-DC front-ends. FNR-3 Power Shelf FNR-3 shelves provide up to 5400 watts in a 19" rack. (See the Rack section for power shelf details.) FNP1500/1800 front-ends have front-mounted AC input receptacles.
BCD.00247 Rev. AA, 07-Nov-12 Page 2 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelves Data Sheet Model Selection Model Input voltage VAC auto selected Output 1 Output 2 Rated power W Compatible Shelf Vo1 nom VDC Io1 max ADC Vo2 nom VDC Io2 max ADC FNP1500-12G 108 – 264 85 – 105 129 @ 11.64V 101.8 @ 11.78A 1512
1212 FNR-3-12G
FNP1500-48G 105 – 264 85 – 105 32.2 25.4 1512
1212 FNR-3-48G
180 – 264 105 – 180 85 – 105 39.2 32.2 25.4 1812 1512 1212 FNR-3-48G 1 The available output power is automatically adjusted depending on the input voltage. 2 1U standard racks are available from Power-One. See the Rack (Power Shelf) section of this data sheet for configurations and details. Absolute Maximum Ratings Stress in excess of the absolute maximum rati ngs may cause performance degradation, adv ersely effect long-term reliability, or cause permanent damage to the converter. Parameter Conditions/Description Min Max Unit Input voltage Continuous Transient, 60 ms max. 264 300 VAC VAC Operating ambient temperature Vi min-Vi max, Io nom, cooling by internal fan @ 100 % load @ 50 % load Storage temperature Non-Operating -40 85 °C Environmental, Mechanical, & Reliability Specifications Parameter Conditions/Description Min Nom Max Unit Altitude Operating Non-Operating 10 k 40 k ASL Ft. ASL Ft. Relative humidity, non-condensing Operating 10 90 % RH Storage 5 95 % RH Temperature coefficient 0 °C to 70 °C (after 15 min warm-up) 0.02 %/K Shock IEC/EN 60068-2-27, 11 ms 40 g pk Sinusoidal vibration IEC/EN 60068-2-6 2-8 Hz 8-200 Hz 200-500 Hz 7.5 mil g pk gpk Random vibration 10-2000 Hz 6.15 g rms MTBF Calculated per Bellcore (SR-332, Issue 1): GB 25 °C GB 25 °C (FNP1500-12G) Demonstrated 230 TBD 250 kh kh kh
BCD.00247 Rev. AA, 07-Nov-12 Page 3 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelves Data Sheet Safety Specifications Maximum electric strength testing is performed in the fact ory according to EN 550116, IEC/EN 60950, and UL 60950. Input-to-output electric strength tests should not be repeated in the field. Po wer-One will not honor any warranty claims resul ting from electric strength field tests. Parameter Conditions/description Min Nom Max Unit Agency approvals UL60950, (UL) CSA 60950 (cUL), EN 60950(TÜV), CE Mark for LVD Insulation safety rating Input to case Input to output Output to case Basic Reinforced Functional Electric strength test voltage Input to case Input to output Output to case Output 1 to output 2 2.12 4.2 0.5 0.1 kVDC kVDC kVDC kVDC Subassemblies are pre-tested with 4.2 kVDC in accordance with EN50116 and IEC/EN60950. EMC Specifications Parameter Description Criterion Electrostatic discharge IEC/EN 61000-4 -2, level 4 Performance criterion B Electromagnetic field IEC/EN 61000-4-3 , level 3 Performance criterion A Electrical fast transients/burst IEC/EN 61000-4-4, level 3 Performance criterion B Surge IEC/EN 61000-4-5, level 3 Performance criterion B Voltage dips and interruptions IEC/EN 61000-4-11 Performance criterion B or better RF conducted immunity IEC/EN 61000-4-6 10 VAC, AM 80 %, 1 kHz Performance criterion A Emissions conducted CISPR 22/EN 55022/EN 61204 Class B Emissions radiated CISPR 22/EN 55022/EN 61204 Class A Harmonics IEC/EN 61000-3-2 Class B Voltage fluctuation and flicker IEC/EN 61000-3-3 Pass Voltage sag SEMI F47-0200 (High Line 230V) Pass Input Specifications Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated. Parameter Conditions/description Min Nom Max Unit Input voltage 85 230 264 VAC Input frequency 47 50/60 63 Hz Turn-on input voltage Ramping up 79 85 VAC Turn-off input voltage Ramping down 70 78 VAC Inrush current limitation 115/230 VAC acc. ETS 300 132-1 < 100 ms Apk Hold-up time After last AC line peak , Vi = 230 VAC, Po nom 20 ms Power factor Vi nom, Io nom 0.95 W/VA Efficiency Vi = 230 VAC, Io nom, TC = 25 °C 89 90 % Max input current 20 A rms Input connector 16A – 20 A / 250 VAC; according to IEC320 C19 87% for FNP1500-12
BCD.00247 Rev. AA, 07-Nov-12 Page 4 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelves Data Sheet Output Specifications, FNP1500-12G Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated. Parameter Conditions/Description Min Nom Max Units Nominal output voltage Io = 64.5 A 12 VDC Output voltage set point accuracy Vi = 230 VAC, Io1 = 65.5 A, TC = 25 °C (Factory setting) 11.93 -0.42 12 12.05 +0.42 VDC % Vo1 nom Output voltage trimming Adjustable via I C (Vo1 set) Adjustable via Margin pin (R input) 6.2 12 13 1 Vo1 set VDC VDC Nominal current output 1 FNP1500-12G Io1 nom @ Vi =108 VAC – 264 VAC, Po 1.5 kW Io1 nom @ Vi = 85 VAC – 105 VAC, Po 1.2 kW 129.0 101.8 129.0 ADC ADC Current limit output 1 FNP1500-12G I o1 max @ Vi = 108 VAC – 264 VAC droop hiccup Io1 max @ Vi = 85 VAC – 105 VAC droop hiccup 147.4 120.2 ADC ADC Nominal current output 2 Io2 nom @ Vi = 85 VAC – 265 VAC, Po 12 W 1.0 1.0 ADC Current limit output 2 Io2 max @ Vi = 85 VAC – 265 VAC 1.5 ADC Static line regulation output 1 Vi min - Vi max, 50 % Io nom, Ta = 25 °C -0.5 0.5 % Vo nom Static load regulation output 1 (droop characteristic) Vi = 230 V, 5 - 100 % Io nom Full load to no load [0..129 A] at Vo set = 12V dVo1 over the setting range [7 to 13V] 11.64 -0.36 - 5.58 12.36 +0.36 mV/A VDC VDC Static load regulation output 2 (droop characteristic) Full load to no load @ Vi = 85 VAC – 265 VAC 0.4 VDC Dynamic load regulation Load change 50 % <─> 100 % Io nom, dIo/dt =1A/s Voltage deviation (droop + over- or undershoot) FNP1500-12G -2 2 % Vo nom FNP1500-12G Max. recovery time to within 1% of Vo1 nom 400 s Current Share FNP1500-12G Difference in current between two units for Vo1 above 10 % load.
12.9 ADC
Time required for output within regulation after initial application of AC-input (Vi nom, Io nom) after removal of inhibit (Vi nom, Io nom) 100 1.5 s ms Output voltage ripple and noise (Filter 10nF/10µF) V i nom, Io nom, 20 MHz bandwidth Vo1 Vo2 120 120 mVpp mVpp Remote sense Total compensation for cable losses 500 mV
BCD.00247 Rev. AA, 07-Nov-12 Page 5 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet Output Specifications, 48Vout Models Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated. Parameter Conditions/Description Min Nom Max Units Nominal output voltage Vo1 Io = 16.1 A 48 VDC Nominal output voltage Vo2 Io = 0.5 A 12 VDC Output voltage set point accuracy Vi = 230 VAC, Io1 =16.1 A, TC = 25 °C (47.8 - 48.2 VDC) -0.5 +0.5 % Vo1 nom Output voltage trimming (via I C or with external resistor) Adjustable (44.16 to 51.84 VDC) -8 +8 % Vo1 nom Nominal current output 1 FNP1500-48G Io1 nom @ Vi =105 VAC – 264 VAC, Po 1.5 kW Io1 nom @ Vi = 85 VAC – 105 VAC, Po 1.2 kW 32.2 25.4 ADC ADC FNP1800-48G Io1 nom @ Vi =180 VAC – 264 VAC, Po 1.8 kW Io1 nom @ Vi =105 VAC – 180 VAC, Po 1.5 kW Io1 nom @ Vi = 85 VAC – 105 VAC, Po 1.2 kW 39.2 32.2 25.4
39.2 ADC
o1 max @ Vi = 105 VAC – 264 VAC droop hiccup Io1 max @ Vi = 85 VAC – 105 VAC droop hiccup 36.8 ADC ADC FNP1800-48G Io1 max @ Vi = 180 VAC – 264 VAC droop hiccup Io1 max @ Vi = 105 VAC – 180 VAC droop hiccup Io1 max @ Vi = 85 VAC – 105 VAC droop hiccup 43.8 36.8 ADC ADC ADC Nominal current output 2 Io2 nom @ Vi = 85 VAC – 264 VAC, Po 12 W 1.0 1.0 ADC Current limit output 2 Io2 max @ Vi = 85 VAC – 264 VAC 1.5 ADC Static line regulation output 1 Vi min - Vi max, 50 % Io nom -0.5 0.5 % Vo nom Static load regulation output 1 (droop characteristic) FNP1500-48G Vi = 230 V, 5-100 % Io nom Vo : full load (32.2 ADC) to no load 46.54 90.1 49.44 mV/A VDC FNP1800-48G Vi = 230 V, 5-100 % Io nom Vo : full load (32.2 ADC) to no load 45.91 90.1 49.44 mV/A VDC Static load regulation output 2 (droop characteristic) V i = 230 V, 5-100 % Io nom Vo : full load (32.2 ADC) to no load
0.4 VDC
Load change 50 % <─> 100 % Io nom, dIo/dt =1 A/s Voltage deviation (droop + over- or undershoot) % Vo nom FNP1500-48G -5 5 % Vo nom FNP1800-48G -5.7 5.7 % Vo nom All models Max. recovery time to within 1 % of Vo1 nom 400 s Current Share Difference in current between two units for V o1 above 10 % load. FNP1500-48G 3.2 ADC FNP1800-48G 3.9 ADC Start-up time Time required for output within regulation after initial application of AC-input (Vi nom, Io nom) after removal of inhibit (Vi nom, Io nom) 100 1.5 s ms Output voltage ripple and noise (Filter 10 nF/10 µF) Vi nom, Io nom, 20 MHz bandwidth Vo1 Vo2 480 120 mVpp mVpp Remote sense Total compensation for cable losses 500 mV
BCD.00247 Rev. AA, 07-Nov-12 Page 6 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet Protection Parameter Conditions/Description Min Nom Max Unit Input fuse Not user accessible 25A, fast blow Inrush current limitation With NTCs Output No-load -, short circuit - and overload proof Overvoltage protection latching Tracking Absolute for 48V models Absolute for 12V models 115 122 59.5 16.85 % Vo nom V V Overtemperature protection Automatic power shutdown at TC 95 °C Remove input voltage to reset. Control Specification is valid for input voltage, load, and temperature ranges, unless otherwise stated. Parameter Conditions/Description Status Indication LEDs: DC OK (green), AC OK (green); fan fail and overtemperature (amber) I C digital bus Monitors alarm functions and sets parameters PS present pin Contact closure to logic ground ( internal pull-down resistor of 1 kΩ) PS remote shutdown / Inhibit pin TTL compatible signal, inhibited when open contact, high or at TTL logic “1”. Signal referenced to logic return (LRTN) Power supply OK (I AC OK & DC OK & no overcurrent & no overtemperature & fans working DC current fail (I Overcurrent on Io1 AC fail / Power down warning C & OC) Provides a warning that the input power has failed at least 5 ms before the output falls out of regulation (<90% Vo1 set). Open collector signal with 20 mA pull-down capability, referenced to logic return (LRTN). AC fail will go high or open during power fail condition and will go low when input is within the operating range. A Power Fail warning will turn off the green AC OK LED. DC fail / Output voltage fault C & OC) Internal undervoltage and overvoltage supervision of Vo1. Open collector signal with 20 mA pull-down capability, referenced to logic return (LRTN). DC fail will go high or open if Vo1 is < 90% or > 110% of Vo1 set, measured in front of the ORing FETs. A green LED on the front panel indicates normal operation. The LED will flash if in parallel operation V o1 is OK, but the unit is disabled. Temperature warning (I C & OC) I C critical temperature warning: Indicate s that the operating temperature has reached [Tshut-down – 10K] I C & OC overtemperature warning: Indicates if the unit is in overtemperature shutdown. Open collector signal with 20 mA pull-down capability, referenced to logic return (LRTN). The OC-output will go low 100 ms before an overtemperature condition shuts down the unit. An amber LED on the front panel indicates overtemperature or fan fail. DC voltage monitoring (I Monitors the voltage Vo1 at the output connector. Accuracy ± 0.45 V over setting range, temperature and load. DC current monitoring (I Monitors the output current Io1 : Accuracy ± 0.4A over the load range. DC voltage trimming C or external resistor) Output voltage trimming Vo1: ± 8 % of Vo set Setting accuracy over I C: ± 50mV at Vo nom, ± 150 mV over setting range Fan speed control (I Two fan speed levels automatically set depending on the internal temperature. The fan speed can be set to full speed or automatic control. Fan OK (I C & OC) Indicates if the fans are operating or have failed. Synch. startup pin Overcurrent signal which can be used for synchr onous startup of units in parallel or to recover from an overload condition. (See application note). Detailed I C information is available from the model’s I C Manual found on the Power-One web site. Provided over the I C interface and as an open collector signal on the output connector (OC).
BCD.00247 Rev. AA, 07-Nov-12 Page 7 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet Output Connector Pinning and Signal Specification Output Connector Fan Fail U1 OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND < 0.4 V @ 20 mA Pull up 15 V 20 mA AC Fail / Power down warning U2 OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND < 0.4 V @ 20 mA Pull up 15 V 20 mA Power Supply Present U3 Resistor (1 k Ω) connected to logic GND Open Pull up 10 V 10 mA DC Fail / Output voltage fault U4 OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND < 0.4 V @ 20 mA Pull up 15 V 20 mA Internal ground U5 Internal ground (Vo1– line before the output filter). Do not connect the internal grounds in systems with several units. ADDR0, I C address bus T1 DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). Switch closed Switch open ADDR1, I C address bus T2 DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). Switch closed Switch open ADDR2, I C address bus T3 DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). Switch closed Switch open ADDR3, I C address bus T4 DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). Switch closed Switch open ADDR4, I C address bus T5 DIP switch or wire to internal ground, Internally pull up to 5V (10 kΩ). Switch closed Switch open DATA, I C data line S1 I C compatible signal referenced to logic GND 5 V or 3.3 V logic CLOCK, I C clock line S2 I C compatible signal referenced to logic GND 5 V or 3.3 V logic Vo2 + output S3 Auxiliary power pin, insulated from main output Vo2 – output S4 Auxiliary ground pin, insulated from main output Logic ground S5 Internally connected over 10 Ω to Auxiliary GND. Wire separately form Auxiliary - and main output GND to minimize noise on signals and I Leave open if not used. Output inhibit R1 PS active when pulled low (DC-DC stage off when left open) Referenced to logic GND < 0.8 V > 2.0 V 10 V 3.5 mA V sense + R2 Open or connected to Vo1+ at the load (Internally connected to Vo1+ over 100 Ω) dU < 3 Vpp 30 mA V sense - R3 Open or connected to Vo1- at the load (Internally connected to Vo1- over 100 Ω) dU < 3 Vpp 30 mA 12V model Output margin 48V models Open or connected over resistor to internal ground. Do not connect the margin pins in systems with several units.
3 VDC
Open or connected to internal ground (+8 % Vo1) or V sense+ (-8 % Vo1) Do not connect the margin pins in systems with several units.
60 VDC
Synch. startup 48V models R5 Open or connected to synch startup circuit, referenced to Vo1 - at the output connector 12V 3mA R5 Open or connected to synch startup circuit, referenced to Vo1 - at the output connector 12V 2mA Vo1 + output 12V model P2, P4, P6, P8, P10, P12 Main output + pins Vo1 – output 12V model P1, P3, P5, P7, P9, P11 Main output – pins Vo1 + output 48V models P2, P4, P6 Main output + pins Vo1 – output 48V models P1, P3, P5 Main output – pins
BCD.00247 Rev. AA, 07-Nov-12 Page 8 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet LED Indicator Functionality Condition Power Fail (AC OK) Output Good (DC OK) Fan Fail and Over - Temperature Normal Operation Green Green OFF Power Supply is inhibited Green OFF Amber Input AC is low OFF OFF Amber Input AC is low or missing OFF OFF Amber/OFF Over-temperature Green OFF Amber Output overload (In regulation) Green Green OFF Output Overloaded (Out of Regulation) Green OFF OFF Fan Fault (No overtemperature shutdown) Green Green Amber Fan Fault (With overtemperature shutdown) Green OFF Amber Power Supply Failed OFF OFF OFF/ Amber Cooling: To achieve best cooling results sufficient airflow through the unit must be ensured. Do not block or obstruct the airflow at the rear of the unit by placing large components directly at the output connector.
BCD.00247 Rev. AA, 07-Nov-12 Page 9 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet Mechanical Data (FNP1500/1800 12V Models) FNP1500/1800 12V Model Output Connector Descriptions Rear View Female Connector: FCI (51732-026 LF) Mates with: 90° output connector type: Part No. FCI (manufacturer): 51762-11202000AA LF 180° output connector type: Part No. FCI (manufacturer): 51742-11202000AA LF Locate information on availability of FCI connectors at http://www.stkcheck.com/evs/fcielectronics/fcisearch.asp Connector drawings available at: http://portal.fciconnect.com/portal/page/portal/FcicntPublic/DocSrchCustDraw IEC AC power cord with C19 connector VDE 16A: Interpower Components Ltd. 70009110250 IEC AC power cord with C19 connector UL 20A: Interpower Components Ltd. 70025110250
BCD.00247 Rev. AA, 07-Nov-12 Page 10 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet Mechanical Data (FNP1500/1800 48V Models) FNP1500/1800 48V Model Output Connector Descriptions Rear View Female Connector: FCI (51732-020 LF) Mates with: 90° output connector type: Part No. FCI (manufacturer): 51762-10602000AA LF; Power-One Part No.: ZES258-G 180° output connector type: Part No. FCI (manufacturer): 51742-10602000AA LF Locate information on availability of FCI connectors at http://www.stkcheck.com/evs/fcielectronics/fcisearch.asp Connector drawings available at: http://portal.fciconnect.com/portal/page/portal/FcicntPublic/DocSrchCustDraw IEC AC power cord with C19 connector VDE 16A: Interpower Components Ltd. 70009110250 IEC AC power cord with C19 connector UL 20A: Interpower Components Ltd. 70025110250
BCD.00247 Rev. AA, 07-Nov-12 Page 11 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet Paralleling Front-Ends: For parallel use in minimal configuration s ystems, only the inhibit pins must be shorte d to logic GND. All other pins can be le ft open. The power supplies will share the output current automatically (droop current share). For parallel applications without I 2C bus, but the use of all other features, it is recommended to connect all logic GND’s on a backplane together, to connect all Vo2 -, all V o2 + and to leave the internal GND’s open. The sense wires can be left open or connected to a common load point, the synch-start pin can be left open or connected to a synch-start circuit, the inhibit pins can be connected together or used individually. All I 2C signals (T1-T5, S1, and S2) can be left open. Use of a small foil capacitor > 3µF directly at the power outputs of each unit is recommended in order to prevent voltage drops at the hot plug. For additional information on paralleling see the following Rack (Power Shelf) section. Racks (FNR-3-12G and FNR-3-48G Power Shelves) Each rack (power shelf) is 1U high with backplane and designed for up to three front-end models in parallel or in n+1 operation . Each power shelf has: Massive copper bus bars for low-loss current distribution. Output terminals with two M4-screws on each power tab. Two fast-on contacts for system earthing. Address coding over five pole DIP switch on each unit, 37-pin D-Sub connector with I 2C-lines, monitoring signals and support functions. Provides a start-up synchronization circuit and EMV filters. FNR-3-12G and FNR-3-48G Power Shelf Front View
BCD.00247 Rev. AA, 07-Nov-12 Page 12 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet Overall Mechanical Dimensions (FNR-3-12G and FNR-3-48G Power Shelves) Output Connector Descriptions (FNR-3-12G and FNR-3-48G) Location Description A 5-Bit DIP switch for I2C addressing of PSU 1 B Earth connection C Earth connection D Earth connection E Output 1 minus F Output 1 plus G 5-Bit DIP switch for I 2C addressing of PSU 2 H 37-pin SUB-D connector, controlling and auxiliary power (output 2) I 5-Bit DIP switch for I 2C addressing of PSU 3 A B C D E F G H I
BCD.00247 Rev. AA, 07-Nov-12 Page 13 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet SUB-D Output Connector Pinout and Signal Specification Output Connector Fan Fail PSU1 1 OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND <0.4 V @ 20 mA Pull up 15 V 20 mA Power Supply Present PSU 1 2 Resistor (1 kΩ) connected to logic GND Open Pull up 10 V 10 mA Power Supply Present PSU 2 3 Resistor (1 kΩ) connected to logic GND Open Pull up 10 V 10 mA Open 4 Overtemperature / Fan Fail PSU 3 5 OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND <0.4 V @ 20 mA Pull up 15 V 20 mA AC Fail / Power down warning PSU 3 6 OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND <0.4 V @ 20 mA Pull up 15 V 20 mA Power Supply Present PSU 3 7 Resistor (1 kΩ) connected to logic GND Open Pull up 10 V 10 mA DC Fail / Output voltage fault PSU 3 8 OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND <0.4 V @ 20 mA Pull up 15 V 20 mA Overtemperature / Fan Fail PSU 2 9 OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND <0.4 V @ 20 mA Pull up 15 V 20 mA Synch._Start_A 10 Sync_start_A , Active high The signals of several racks can be connected together in such a way that all supplies will be inhibited until the last supply has recovered from its overcurrent condition, referenced to logic GND <7V off < 9V 15V 10mA Open 11 Output inhibit PSU 1-3 12 Active low (DC-DC stage off when pin is open or on high potential) Referenced to logic GND <0.8 V >2.0 V 10 V 3.5 mA V sense + 13 Open or connected to Vo1+ at the load Internally (PSU) connected to Vo1+ over 100 Ω dU < 3 V pp 30 mA V sense - 14 Open or connected to Vo1- at the load Internally (PSU) connected to Vo1- over 100 Ω dU < 3 V pp 30 mA Open 15 NC 16 NC 17 NC 18 NC 19 AC Fail/ Power-down warning PSU 1 20 OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND <0.4 V @ 20 mA Pull up 15 V 20 mA DC Fail/ Output voltage fault PSU 1 21 OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND <0.4 V @ 20 mA Pull up 15 V 20 mA AC Fail/ Power-down warning PSU 2 22 OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND <0.4 V @ 20 mA Pull up 15 V 20 mA DC Fail/ Output voltage fault PSU 2 23 OC-output, protected by 16 V Zener diode and a 10 Ω resistor in series, referenced to logic GND <0.4 V @ 20 mA Pull up 15 V 20 mA DATA, I2C data line 24 I2C compatible signal referenced to logic GND 5 V or 3.3 V logic
BCD.00247 Rev. AA, 07-Nov-12 Page 14 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet SUB-D Output Connector Pinout and Signal Specification (Continued) Output Connector CLOCK, I2C clock line 25 I2C compatible signal referenced to logic GND 5 V or 3.3 V logic Auxiliary power +12 V (Output 2) 26 V o2+ Aux output, insulated from main output Auxiliary power ground (Output 2) 27 V o2- Aux output, insulated from main output Logic Gnd 28 Internally connected over 10 Ω to Vo2-, Auxiliary GND. Wire separately from auxiliary and main output GND to minimize noise and avoid voltage drops on signal- and I2C return. Leave open if not used. Output margin PSU 1 29 Open or connected to V sense- V sense- (+8 % Vo1) or V sense+ (-8 % Vo1) 60V Output margin PSU 2 30 Open or connected to V sense- V sense- (+8 % Vo1) or V sense+ (-8 % Vo1) 60V Output margin PSU 3 31 Open or connected to V sense- V sense- (+8 % Vo1) or V sense+ (-8 % Vo1) 60V NC 32 NC 33 NC 34 NC 35 NC 36 NC 37 Synchronized start-up circuit for paralleling operation Because of hiccup overcurrent protec tion, when a supply reaches an overcurrent limit, the output voltage will immediately turn OFF and after a delay turn ON again. In parallel use, all power supplies have to start synchronized because of the internal hiccup behavior. Otherwise, the supply which has reached overcurrent first will go to hiccup; this will overload the other supplies, which then will also go to hiccup. When the first supply has recovered from hiccup (hiccup dead time), the others remain in hiccup. Th is will immediately drive the first one into hiccup once again. This means that without a start-up circuit, a syste m with several power supplies can never recover from an overload condition or start-up into full load. The following additional circuit, required to reach sync hronized startup, is already implemented inside the FNR-3-12G and FNR-3-48G shelves.
BCD.00247 Rev. AA, 07-Nov-12 Page 15 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet Synch Start-up Connection Between Shelves The following connection between the shelves is required to achieve a parallel operation. The synch-start circuits inside the shelves inhibit all power supplies until the last one has recovered from its overcurrent condition and then synchronize the restart of the outputs. Synch Start-up Circuit Description Description Pin Location, Definition Type Low level High level V max I max Auxiliary power +12 V (Output 2) Vo2+, Aux output, insulated from main output Logic ground 28 Logic_GND ,Internally connected over 10 Ω to Vo2-, ( Auxiliary power ground (Output 2)) Output inhibit_A PSU 1-3 12 Inhibit_A ,Active low (DC-DC stage off) Referenced to Logic_GND <0.8 V >2.0 V 10 V 3.5 mA Synch. Startup 1 PSU 1-3 (at PSU) The synch_start pin is connected to the overcurrent signal of the PSU1-3. In the case of an overcurrent shutdown, this signal goes high. Referenced to Vo1- <7V off > 9V 15V 10mA Synch. Startup_A Rack FNR-3-12G & Rack FNR-3-48G 1-N Pin on the D-Sub connector on the backplane Sync_start_A , Active high The signals of several racks can be connected together in such a way that all supplies will be inhibited until the last supply has recovered from its overcurrent condition. Referenced to Logic_GND NOTE: The Sync-Start pins can be wired together only if the power supplies are connected with a minimal voltage drop on power ground as achieved on a backplane with massive copper bus bars. If there is a less ideal connection, it is recommended to use an opto-coupler for each unit (IC1, D3, D2).
BCD.00247 Rev. AA, 07-Nov-12 Page 16 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet Mechanical Data (FNR-3-12G and FNR-3-48G Power Shelves Accessories: Center Angular Brackets are set in the middle for shelf mounting: Center Angular Bracket sets can be ordered: Power-One part no.: HZZ01222 Note: Each Center Angular Bracket set contains 2 brackets and 8 screws.
BCD.00247 Rev. AA, 07-Nov-12 Page 17 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet Filler for covering empty shelf slots: Filler can be ordered: Power-One part no.: XAK.00043.0 Plastic cover set for the bus bars: Plastic cover set can be ordered: Power-One part no.: XEB.00031.0 Note1: Available upon special request. Note2: Each plastic cover set contains 2 pieces.
BCD.00247 Rev. AA, 07-Nov-12 Page 18 of 18 www.power-one.com FNP1500/1800 Front-Ends & FNR-3 Power Shelf Data Sheet Fulcrum: The handle has been designed to allow easy plug-in and -out in a rack system. The handle (lever) fits into a counter piece (fulcrum) which is fixed to the bottom of the rack. During the plug, the fulcrum holds the unit down and guides it towards the output connector. The Power-One part number of the fulcrum and its associated mounting accessories is: HZZ01223. Individual fulcrum sets can be also ordered: Power-One part no.: HZZ01223. Note: Each HZZ01223 set contain 2 fulcrums, 2 supports, and mounting accessories. I2C to USB Interface HZZ02002G: I2C Management Software : All FNP front-ends can be controlled via Power-One's GUI-driven I 2C Management software and an I 2C-to-USB interface (P/N HZZ02002G). An I 2C Programming Manual describes the complete range of parameters that can be programmed to the FNP1500/1800 front-ends. This manual is available by searching on "FNP1500" at www.power-one.com. NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not des igned, intended for use in, or authorized for use as critical components in life support systems, equipment used in hazardous envir onments, or nuclear control systems without the express wr itten consent of the respective divisional president of Power-One, Inc. TECHNICAL REVISIONS - The appearance of products, including safe ty agency certifications pictured on labels, may change dependi ng on the date manufactured. Specifications are subject to change without notice. I2C <to>USB Interface