HVP-56F82748 FREESCALE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

High–Voltage Development Platform

High-Voltage Development Platform The Freescale High-Voltage Development Platform is a set of software and hardware tools for evaluation and development of high-voltage motor control and power conversion algorithms. It is ideal for rapid prototyping of high- voltage microcontroller-based applications. Quick Start Guide Get to Know the HVP-56F82748 Figure 1: HVP-56F82748 MC56F82748 MCU Isolated Power Supply USB Mini for Power Supply Primary Interface JTAG Isolator Main Board Interface

freescale.com Introduction to HVP-56F82748 High-Voltage Development Platform The HVP-56F82748 controller card is a development platform for the DSC56F8xxxx family which in combination with one of HVP-MC3PH High-Voltage Development Platform provides ready-made software and hardware development for high-voltage motor control and power conversion applications. This Quick Start Guide will teach you to:

  • Easily program examples for the DSC56F8xxxx family
  • Spin the 3-phase PMSM motor of the HVP-MC3PH module while monitoring the motor with the FreeMASTER tool HVP-56F82748 Controller Card Features
  • Accommodates target MC56F82748VLH MCU (32-bit DSP core with single-cycle math computation, 100 MHz, 64 KB flash, 2x12-bit ADCs, high-resolution PWM, 64 LQFP) SWD isolation up to 5KV
  • Galvanic Isolation
  • Design optimized for low noise
  • On-board isolated power supply, allowing safe debugging
  • Controller card allows stand-alone operation Tools Required
  • CodeWarrior Development Studio for MCU version 10.6
  • Freescale FreeMASTER for real-time debug monitoring and data visualization
  • Download and install the CodeWarrior Development Studio for MCU version 10.6.
  • Download and install the driver for USB to serial controller CP210x.
  • Download and install the free debug monitoring and data visualization tool Freescale FreeMASTER, v1.4 or later, at freescale.com/FreeMASTER. Debug Motor Control Project in CodeWarior with HVP-MC3PH High- Voltage Development Platform 1) Configuring Hardware
  • Plug the controller card HVP-56F82748 into 64-pin PCI connector located at HVP-MC3PH.
  • Configure jumpers at HVP-MC3PH as is shown in the table below. Option Setting J1 1–2, 2–3 J3 1–2, 2–3
  • Close the lids.
  • Connect the servo motor leads to output connector J13. (Applications are tuned for Servo motor type: Mige 60CST-M01330 or Maxsine 60MSLO1330FC).
  • Connect mini USB cable between controller card and your computer Step-by-Step Installation Instructions Download Software and Tools Download installation software and documentation under “Jump Start Your Design” at freescale.com/HVP.

freescale.com Step-by-Step Installation Instructions to provide power supply for galvanic isolator.

  • Connect debugger (USB TAP , or PE micro multilink ) to J1 JTAG connector. Loading the PMSM Motor Demo Software
  • Launch CodeWarrior and Build the “PMSM_sensorles_FOC”. Open the CodeWarrior project file .project following the path Project Labs\\ PMSM_sensorles_FOC\\ in the Quick Start Package. Clean the project before selecting the action Rebuild All. Note: The compilation may return warning messages without consequence.
  • Run CodeWarrior Debug Mode and Download and Debug the “PMSM_ sensorles_FOC” project.
  • Connect a line-isolated, current-limited

110 V DC or 90 V AC power supply to

the power input module with the IEC connector. The power supply current limit should be set for less than 3 amps. The DC supply’s polarity does not matter. Regardless whether DC or AC power is used, the power is always applied to the input power connector located on the rear panel.

  • Start the debug session by selecting the GO option from the toolbar. To spin motor and set motor speed, continue to following section.

Step-by-Step Installation Instructions Monitor the Project with FreeMASTER

  • Launch Freescale FreeMASTER v1.4 or later from the Windows Start menu.
  • Connect USB cable between USB on HVP-MC3PH and your computer.
  • Windows will detect a UART to USB bridge.
  • Open the FreeMASTER project file PMSM_Sensorless_DSC.pmp following the path Project Labs\\ Freemaster\\PMSM_ Sensorless_FOC in the Quick Start Package. The PMSM Sensorless Application interface will appear in FreeMASTER to monitor and control the speed, the voltage and the current consumption of the motor.
  • In the Project Options, set the COM port affected as the CP210x USB to UART Bridge (information available in Device Manager) and set the baud rate/ speed to 19200 bps (check the option Do Not Open Port at Startup to avoid error messages at FreeMASTER startup)
  • From the toolbar, select the action Start the Communication.
  • Select in FreeMASTER speedometer; the requested speed and the motor will spin automatically.

Visit freescale.com/support for a list of phone numbers within your region. Warranty Visit freescale.com/warranty for complete warranty information. Get Started Download installation software and documentation under “Jump Start Your Design” at freescale.com/HVP. For more information, visit freescale.com/HVP , freescale.com/Kinetis, freescale.com/Kinetis/ VSeries, or freescale.com/DSC Freescale, the Freescale logo and Kinetis are trademarks of Freescale Freescale Semiconductor, Inc. ARM and Cortex are registered trademarks of ARM Limited (or its subsidiaries) in the EU and/or elsewhere. All rights reserved. All other product or service names are the property of their respective owners. © 2015 Freescale Semiconductor, Inc. Doc Number: HVP56F82748QSG REV 0