W.FL2_17 HIROSE | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
2.0mm 2.0mm Ultra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height W.FL2 Series 2014.11w ■Features 1. Nominal mated height of 1.18 mm (Max. 1.3 mm) 2. Small board footprint As with X.FL, W.FL Series, the receptacles occupies an area of 3.4 mm2 and share the same land pattern. Note: The W. FL2 Series is not compatible with X.FL, W.FL Series. 3. Extremely light weight The world's smallest and lightest class of coaxial connectors. Receptacle: 5.0mg Right angle plug:16.7mg(062), 17.4mg(040), 15.3mg(032) 4. Frequency range up to 6 GHz 5. Automatic board placement Packaged on tape-and-reel the receptacles can be placed with vacuum nozzles of the automatic placement equipment. 6. Plugs are terminated with ultra-fine coaxial (fluorinated resin insulated) cable The use of ultra-fine coaxial(fluorinated resin insulated)cables on these connectors offer the ability to complete connections in small, confined spaces with a smooth, easy operation. 7. Simple connector mating / un-mating Use of the available mating / un-mating tools assures correct connection / disconnection of the plug and receptacle. 8. Halogen-free*(Receptacle, Plug(HF type)) *As defined by IEC61249-2-21 Br-900 ppm maximum, Cl-900 ppm maximum, Cl+Br combined-1,500 ppm maximum. W. FL2 Series W. FL Series [MAX1.55] 1.4 1.18 [MAX1.3] W.FL2-LP-032HF(06) W.FL2-LP-040(06) W.FL2-LP-040HF(06) W.FL2-LP-062HF W.FL-LP-040(06) W.FL-LP-040HF(06) W. FL SeriesW. FL2 Series W.FL2-R-SMT-1 W.FL-R-SMT-1 (#( 8VWaZ L#;A'Eaj\\ &#&- PB6M&#(R GZXZeiVXaZ Mated height comparison (with W.FL Series) Occupied Mounting Area W. FL2 Plug and Receptacle Fig.2 Fig.1
W.FL2 Series●Ultra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height ■Specifications Rating Nominal characteristic impedance 50ø Operating temperature range -40°C to +90°C (90%RH max.) Frequency range DC to 6 GHz Storage temperature range Item Specification 1. Contact resistance 20 mø max. (center contact), l0 mø max. (outer contact) 2. Insulation resistance 500 Mø min., 100 V DC 3. Withstanding voltage 200 V AC / 1 minute 1.4 max. (3 GHz to 6 GHz) * V.S.W.R. Measurement as shown on the block diagram below. Note: Verify connection and measurement setup. Note1. The term “storage” refers to products stored for long period of time prior to mounting and use. Note1: Cable assembly measurements with SMA conversion adapters mated with W.FL2 plug at each end of the 100cm long ultra-fine coaxial cable. Note2: Receptacles mounted on a 50 ohms glass epoxy board. Measurements were conducted with SMA conversion adapters attached. Network Analyzer Test Set Test Port TerminationD.U.T Test Post Cable -30°C to +70°C (90%RH max.)Note 1 ■Materials■Materials
- Plugs – Right Angle Part Material Finish Shell Phosphor bronze Silver plated/Gold plated(062) Insulator PBT Color: Black, UL94V-0 Insulator (HF type) LCP Color: Milky white, UL94V-0 Female center contact Phosphor bronze Gold plated
- Receptacle Part Material Finish Shell Phosphor bronze Silver plated Insulator LCP Color: Black, UL94V-0 Male center contact Brass Gold plated
W.FL2 Series●Ultra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height ■Cable Assembly(Plug) [Plugs can be ordered only as terminated cable assemblies.] 20.91 3.3 W.FL2-LP-040(06), W.FL2-LP-040HF(06) (Applicable cable : outer diameter 0.81) 3.3 0.89 W.FL2-LP-062HF (Applicable cable : outer diameter 1.0) 3.35 0.91 2 W.FL2-LP-032HF(06) (Applicable cable : outer diameter 0.5)
W.FL2 Series●Ultra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height BHow to specify Cable Assembly ■Ordering information ●Standard Tolerances for (L) L (mm) [Double-ended cable assembly] L (mm) [Single-ended cable assembly] Ordering infometioan (L)mm Standard tolerance(mm) *L=35 to 200 ±4 1L=200 to 500 ±8 1L=500 to 1000 ±12 L=Longer than 1000mm1000 ±1.5% of (L) Note: Minimum available length(L) is 35mm. Used plug: W.FL2-LP-040(06), W.FL2-LP-040HF(06) W.FL2 − 2LP − HF6 − 04NʮʯTV −A− (L) W.FL2 − LP − HF6 − 04NʮʯTV −A− (L) Double- Ended Single- Ended Used plug: W.FL2-LP-062HF W.FL2 − 2LP − HF − 062NʮʯSC −A− (L) W.FL2 − LP − HF − 062NʮʯSC −A− (L) Double- Ended Single- Ended Used plug: W.FL2-LP-032HF(06) W.FL2 − 2LP − HF6 − 032NʮʯTS −A− (L) W.FL2 − LP − HF6 − 032NʮʯTS −A− (L) Double- Ended Single- Ended ⁞ Series name : WFL2, W.FL2 Assembly type LP: Single ended 2LP: Double ended Environmental compliant HF6: Halogen-free 6: RoHS compliant Cable type 04N: 0.81mm dia. ultra-fine coaxial cable Cable color 1: White, 2: Black Cable outer conductor TV: Tin Plated braided wire Total length (mm) Length(L) ⁞ Series name : WFL2, W.FL2 Assembly type LP: Single ended 2LP: Double ended Environmental compliant HF6: Halogen-free Cable type 032N: 0.5mm dia. ultra-fine coaxial cable Cable color 1: White, 2: Black Cable outer conductor TS: Tin Plated fiber or paper covered copper winding wire Total length (mm) Length(L) ⁞ Series name : WFL2, W.FL2 Assembly type LP: Single ended 2LP: Double ended Environmental compliant HF: Halogen-free Cable type 062N: 1.0mm dia. ultra-fine coaxial cable Cable color 1: Gray, 2: Black, 3: White Cable outer conductor SC: Outer tin plated braided wire Inner conductor silver plated Total length (mm) Length(L)
W.FL2 Series●Ultra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height ■Receptacles 0.7 0.3 1.7
0.3 SIG
1.3 1.7 0.25 2.6 1.4 0.5 SIG GND No conductive traces in this area 1.31.3 1.5 0.65 BRecommended PCB mounting pattern (Note 1) Note 1: The land pattern is the same as that of the X.FL, W.FL series connectors. BEmbossed Carrier Tape Dimensions (IEC 60286-3 compliant) Embossed Carrier Tape Dimensions Reel Dimensions ¢((% &(#* ¢&( ¢'& BViZg^VaɿEH L]^iZ H86A:;G:: Embossed Carrier Tape Dimensions (W.FL2-R-SMT-1(60) 8mm pitch) ' ) П&#* (W.FL2-R-SMT-1(80) 4mm pitch) Part No. HRS No. Packaging RoHS W.FL2-R-SMT-1(60) 331-0315-4 60 Reel (5,000 pcs/reel) Yes W.FL2-R-SMT-1(80) 331-0315-4 80 Reel (10,000 pcs/reel)
W.FL2 Series●Ultra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height ■Conversion Adapters Note: Used for performance measurements only. The W.FL2 mating side has lower retention force when mated with the corresponding part. Note: Used for performance measurements only. The W.FL/W.FL2 mating side has lower retention force when mated with the corresponding part. Note: When mating with corresponding part (W.FL2-R- SMT-1) must be pressed down and held to make complete connection. SMA Conversion Adapter (W.FL2/W.FL side plug – SMA side jack) SMA Conversion Adapter SMA Conversion Adapter (W.FL2 side jack – SMA side plug) ■Receptacle Inspection Adapter (W.FL2/W.FL) Used for inspecting the performance parameters of the cable assembly. 8HEX(10.15) (4.05)6 1/4-36UNS-2A 13.8 Ø6.35 5.6 (18.14) (4)6 1/4-36UNS-2A Ø6.35 5.5 (4.4) 1 (7.9) 4.2 12.1 M5∞0.5 7HEX All dimensions: mm All dimensions: mm All dimensions: mm All dimensions: mm Part No. HRMP-W.FL2J HRS No. Packaging RoHS Yes311-0394-6 1 Part No. HRMJ-W.FLP(40) HRS No. Packaging RoHS Yes311-0368-6 40 1 Part No. HRMJ-W.FL2P-ST3 HRS No. Packaging RoHS Yes311-0417-0 1 Part No. W.FL-R-1 HRS No. Packaging RoHS Yes331-0483-9 1
W.FL2 Series●Ultra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height BTools Plug - Mating /Unmating (W.FL2-LP-040HF/032HF) This tool is for mating and unmating a plug. Plug - Mating (Space saving type) This tool is used for mating a plug. Plug-Mating/Unmating (W.FL2-LP-062HF) This tool is for mating and unmating W.FL2-LP-062HF plug. M#;A BVi^c\\ZcY JcbVi^c\\ZcYM#;ABVg\`^c\\ Part No. HRS No. RoHS X.FL-LP-IN.OUT1 331-0715-2 Yes Note: Can be used with X.FL plug. (100) Ø108 Part No. HRS No. RoHS W.FL-LP-IN 331-0323-2 Yes Note: Can be used with W.FL, X.FL plugs. (60) Mating end Unmating end Part No. HRS No. RoHS W.FL2-LP-IN.OUT 331-0321-7 Yes
W.FL2 Series●Ultra-Small Surface Mount Coaxial Connectors - 1.18mm Mated Height ■Precautions 1. Plugs
- Use of the extraction tool is absolutely mandatory. Any attempt of unmating by pulling on the cable may result in damage and affect the mechanical / electrical performance. Unmating Mating (1) Recommended reflow temperature profile q The temperature of the printed circuit board surface temperature at the points of contact with the terminals. w Reflow soldering should be performed at a printed circuit surface temperature of 250°C max. e In individual applications the actual temperature may vary, depending on the solder paste type, volume / thickness and board size / thickness. Consuly your solder paste and equipment manufacturer for specific recommendations. (2) Recommended metal mask thickness (3) Reflow cycles 2. Receptacles 100 120 140 160 180 200 220 240 260 [ç] Preheat (130 to 180ç) 230ç 220ç 50 seconds max. 120 seconds max. 60 seconds max. Time 250 ç max. for 10 seconds (1) Mating / Unmating (3) Precautions q Align the mating axes of the plug and the receptacle. w Confirm that the plug is positioned to be guided. (The both axes are aligned and the plug is positioned stably.) e Remove the tool by carefully pulling it up. q To disconnect connectors, insert the extraction side of insertion and extraction jig and perform as described in the diagram below. Do not twist connectors excessively during mating / unmating. 3FNPWBM DPNQMFUFE *OTFSU UIF FYUSBDUJPO TJEF PG UIF UPPMVOEFSUIFNBUFEQMVHBUUIF DBCMFDPOOFDUJPOTJEF BTTIPXO 5JMUUIFUPPMBTTIPXO BOEMJGUUIFQMVHDBCMF BTTFNCMZ >chZgiidgZXZeiVXaZEaj\\e^X\`je GZbdkVad[ i]Zidda L#;A'"AE" Eaj\\ :@.;= Do not apply any pull forces after the bending of the cable. (2) Pull forces on the cable after connectors are mated 0.1 mm to 0.12 mm 2 times (1) Operating environment The connectors are not designed to operate in the following environments: Exposed to a excessive amounts of fine particles and dust Regions and places having a high density of sulfur dioxide, hydrogen sulfide, nitrogen dioxide or other corrosive gasses. Environments having large rapid variations in temperature. (2) Storage conditions - Receptacle Store in the Hirose Electric packaging. Temperature: -10 to +40ç, Humidity: 85% max. Use within 6 months of delivery. Receptacles for which the storage period has elapsed must be tested for solderability to the PC board mounting surface. 3. Operating environment and storage conditions L#;A'"AE" 'CbVm# %+'%)%ineZ &CbVm# %('ineZ 2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN TEL: +81-45-620-3526 Fax: +81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 11/2014. Contents are subject to change without notice for the purpose of improvements. Powered by TCPDF (www.tcpdf.org)