U.FL-R-SMT HIROSE | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
Ultra Small SMT Coaxial Connectors - Low Profile 1.9mm or 2.4mm Mated Height U.FL Series 2003.9 1.9(2.0Max) 2.4(2.5Max) 3(3.2Max)U.FL-LP(V)-040 U.FL-LP-040 U.FL-LP-066 E.FL-LP-040 E.FL-LP-066 U.FL Series E.FL Series U.FL-LP-040 U.FL-LP-066 U.FL-LP(V)-040 U.FL-LP-062 U.FL-LP-088 U.FL-R-SMT U.FL-R-SMT U.FL-R-SMT U.FL-R-SMT U.FL-R-SMT Dia.0.81Dia.1.32 Dia.1.13 I Features 1. Low Profile: 1.9mm or 2.4mm Nom. Mated Height Height from the circuit board is 2.0mm or 2.5mm maximum when a plug (right angle) is mated to a receptacle, which ranks with world’s smallest class. 2.Extremely Small Occupied Mounting Area In comparison with our SMT coaxial connectors E.FL series, the receptacle provides a reduction of approximately 18% of occupied mounting surface, which is only 7.7mm 3.Light Weight One of the world’s lightest coaxial connectors. Receptacle: 15.7mg 4.Applicable Up to 6 GHz Frequency To meet the frequency requirements of a wide variety of miniature equipment, these connectors offer high frequency performance from DC to 6 GHz. 5.Board placement with automatic equipment Supplied on tape-and-reel packaging. 6.Use of Ultra-fine Teflon Cable From among the types of applicable cable, dia. 0.81mm(single shielded) ultra-fine Teflon coaxial cable has been made a standard specification in construction area. Refer to the following pages for different cable types. 7.Simple Removal of Connector The extraction jig permits simple removal of connectors. 8.User Friendly Mating Operation Tactile lock feeling ensures engagement even with this small size. I Applications Mobile phones, Wireless LAN, Mini-PCI, Bluetooth, PDA, GPS, electronic measuring instruments, etc. Mated Height Comparison (With Hirose Product) G Space Factor of Mated Connector Meets up to 6 GHz Requirement NEW NEW NEW
*V.S.W.R. Measurement System Note 1: Cable type connectors were measured with SMA conversion adapters attached to both ends of the harness product of a suitable 100cm cable. Note 2: Board type connectors were mounted to a 50Ω glass epoxy board and measurements were conducted with SMA conversion adapters attached. Ratings Nominal characteristic impedance Voltage rating Frequency range 50 ohms
60 V AC (rms)
Operating temperature range Operating humidity -40˚C to +90˚C 90% max. Part Material Finish Remarks Shell Phosphor bronze Silver plating ————— Male center contact Brass Gold plating ————— Female center contact Phosphor bronze Gold plating ————— Insulator Plug Color: Black UL94V-0 Receptacle Color: Beige UL94V-0LCP PBT I Materials 1. Contact resistance 2. Insulation resistance 3. Withstanding voltage 5. Female contact holding force 6. Durability (mating/un-mating, with corresponding plug) 7. Vibration 8. Shock 9. Humidity (Steady state) 10. Temperature cycle 11. Salt spray test Item Specification Conditions Center: 20 m ohms max. Outside: 10 m ohms max. 500 M ohms min. No flashover or insulation breakdown. 0.15 N min. Contact resistance Center: 25 m ohms max. Outside: 15 m ohms max. No electrical discontinuity of 1µs min. No damage, cracks or parts dislocation. No damage, cracks or parts dislocation. Insulation resistance 100 M ohms min.(when humidity high) Insulation resistance 500 M ohms min.(when dry) No damage, cracks or parts dislocation. Contact resistance:25 m ohms max. (Center) 15 m ohms max. (Outside) No excessive corrosion 10 mA max.
100 V DC
200 V AC / 1 minute
Measured with a Ø 0.475 pin gauge 30 cycles Frequency: 10 to 100 Hz, single amplitude of 1.5mm, acceleration of 59m/s2, for 5 cycles in the direction of each of the 3 axis. Acceleration of 735 m/s 2, 11ms duration, sine half-wave waveform, 2 cycles in each of 3 axes. 96 hours at temperature of 40ç and humidity of 95%. Temperature:-40˚C Time: 30 / 5 max. /30 /5 max.(Minutes) 5 cycles 5% salt water solution, 48 hours Part No. Up to 3GHz 3 to 6GHz U.FL-LP-062 dia.1mm Coaxial Cable Assembly 1.3 Max 1.3 Max
Part No. Mated Height Applicable cable Weight (mg) Coaxial cable Coaxial cable Coaxial cable Coaxial cable Coaxial cable Coaxial cable Coaxial cable Coaxial cable Dia. 1.13mm and Dia. 1.32mm Coaxial cable I Cable Assembly (Plug) G Cable Guide I How to Specify Cable Assembled Plug Dimension of U.FL Series assembly products should be made as indicated below. Double-Ended Cable Assembly Single-Ended Cable Assembly U.FL - [] LP - [] - A - (L) G Ordering Information Series name U.FL Total Length(mm) 00350<=L<=00200 02000<L<=00500 05000<L<<=01000 10000<0L<=1000 Standard Tolerance (mm) ±04 ±08 ±12 ±1.5% G Total Standard Tolerance for Total Length of Cable Assembly Note: Shortest length L is 35 mm. L L 31 2 4 Assembly type LP: Single ended 2LP: Double ended Cable type 04 : Dia.0.81mm Coaxial Cable 068 : Dia.1.13mm Coaxial Cable 066 : Dia.1.32mm Coaxial Cable 062 : Dia.1 mm Coaxial Cable 088 : Dia.1.37mm Coaxial Cable Total Length(mm) Length is expressed in mm units. Please contact Hirose Sales Representative for cable length and cable end treatment. U.FL-LP-040 U.FL-LP-062 U.FL-LP-088 Dia.0.81mm Coaxial Cable 7/0.05 SA (AWG36) Dia.0.40 PFA Single Shield SA Dia.0.81 PFA 50 ohms 6.45dB/m 9.42dB/m Dia.1.13mm Coaxial Cable 068 7/0.08 SA (AWG32) Dia.0.68 FEP Single Shield SA[TA] Dia.1.13 FEP 50 ohms 3.43dB/m [3.73dB/m] 5.13dB/m [5.44dB/m] Dia.1.32mm Coaxial Cable 066 7/0.08 SA (AWG32) Dia.0.66 FEP Double Shield TA Dia.1.32 FEP 50 ohms 3.8dB/m 5.6dB/m Dia.1mm Coaxial Cable 062 7/0.071 SA (AWG33) Dia.0.62 FEP Tape, single Shield TAT Dia.1 FEP 50 ohms 3.1dB/m 4.4dB/m Dia.1.37mm Coaxial Cable (data as provided by material suppliers, for reference only) * SA : Silver plated annealed copper wire, TA : Tin plated annealed copper wire, TAT : Tin plated copper wire alloyed with tin 088 7/0.102 SA (AWG30) Dia.0.88 FEP Single Shield TA Dia.1.37 FEP 50 ohms 2.8dB/m 4.3dB/m
Description
Conductor* Dielectric Diameter Outer Conductor* Jacket Diameter Nominal Impedance Nominal attenuation At 3GHz At 6GHz 1.93 31.85 U.FL-LP-066 31.93 U.FL-LP(V)-040 3.4 2.81.5 2.81.8
Part No. U.FL-R-SMT(01) U.FL-R-SMT(10) CL No. 331-0471-0-01 331-0471-0-10 Packaging Bag packaging (100 pieces/bag) Reel packaging (2500 pieces/reel) Weight (mg) 15.7/unit I Receptacles Note 1: Receptacles of (01) specification are sold by the pack with 100 pieces per pack. Please order in pack units. Note 2: Receptacles of (10) specification are sold by the reel (which contains 2,500 pieces). Please order in reel units. Note 3: Permissible value for mold resin which gets onto the center contact. G Packaging Specifications Embossed Carrier Tape Dimensions Reel Dimensions GND GND GND GND Cut Out Prohibition Area Recommended PCB Footprints SIG SIG 2.6 0.6 1.25 0.35 1.05ʶ0.05 1ʶ0.05 1ʶ0.05 2.2ʶ0.05 4ʶ0.05 1.9ʶ0.05 1.2Max(NOTE 3) (3.1) 2.6 1.8 1.75ʶ0.1 12ʶ0.3 8ʶ0.1 2ʶ0.1 4 ʶ0.1 0.3 1.6 Center contact Unreeling direction 5.5ʶ0.1 Ø1.5 +0.1 1.8 14 Ø13 Ø21 Ø330ʶ2
Part No. HRMP-U.FLJ CL No. 311-0300-2 I Conversion Adapter G SMA Conversion Adapter (Mating portion: U.FL side jack - SMA side plug) Note:The U.FL side mating portions has a lower lock retention force than the regular product, therefore, cannot be used for purposes other than performance measurements. (10.7) 8HEX 1.1 Ø1.9 Part No. U.FL-R-1 CL No. 331-0466-0 I Receptacle for Check This receptacle is used for inspecting the continuity, withstand voltage, and other aspects of the harness product. This receptacle is used for check the continuity, withstanding voltage, and other performance of the cable assembly products. Note: Part No. U.FL-LP-N-2 for U.FL-LP-040/066/088. 12.9 5 7HEX M5ʷ0.5 (7.9) (4.4) Part No. U.FL-LP-N-2 U.FL-LP(V)-N-2 CL No. 331-0494-5 331-0493-2 I Extraction Jig This jig is used for extraction from a mating condition. U.FL Ø15 (90) 52.1 Part No. HRMJ-U.FLP CL No. 311-0301-5 G SMA Conversion Adapter (Mating portion: U.FL side plug - SMA side jack) Note:The U.FL side mating portions has a lower lock retention force than the regular product, therefore, cannot be used for purposes other than performance measurements. 14.05 Ø6.35 1/4-36UNS-2A 6 5.6 (4.05) Part No. HRMJ-U.FLP-ST1 CL No. 311-0385-5 G SMA Conversion Adapter (Mating portion: U.FL side plug-SMA side jack) Note: This connector is used by compressing the mated portion of U.FL side onto the U.FL-R-SMT portion. (18.6) 1/4-36UNS-2A 6 5.5(4)
- Plugs (1) Connection/ disconnection of connectors (2) Permissible load on the cable after connector mating. (3) Precautions 1) To disconnect connectors, hook the end portion of U.FL-LP-N-2 and U.FL-LP(V)-N-2 onto the connector cover and pull off vertically in the direction of the connector mating axis. 1) To remove the connector directly, hold the connector cover and pull off vertically in the direction of the connector mating axis. (Please exercise caution so as not to injure fingertips or nails.) 2) To mate the connectors, the mating axes of both connectors are aligned and the connectors are inserted as perpendicularly as possible. Do not attempt to insert on an extreme angle. After the connectors are mating, do not apply a load to the cable in excess of the values indicated in the diagram below. Do NOT forcefully twist or deform wires. (1) Recommended temperature profile (Reference) 1) The temperature profile indicates the board surface temperature at the point of contacts with the connector terminals (for surface mounted receptacle). 2) The temperature profile will change depending on conditions which include such factors as the size of the board, the solder used, and the solder thickness. (3) Recommended screen thickness 0.1 to 0.15 mm (2) Recommended manual soldering (Reference) Manual soldering: 350˚C for 5 seconds 2. Receptacles U.FL-LP-040 2N max. 2N max. 4N max. U.FL-R-SMT Temperature on Top Portion of Part Time Preheating (130 to 165ˆ) Within 2 minutes 40 to 50 seconds Heating peak 240ˆ 3 seconds 183ˆ 260 240 220 200 180 160 140 120 100 (ˆ) Extraction Jig U.FL-R-SMT U.FL Cable Assembly
NOTES :
The contents of this catalog are current as of date of publication. Contents are subject to change without notice for the purpose of improvements. USA: HIROSE ELECTRIC U.S.A., INC.
2688 Westhills Court, Simi Valley, CA 93065-6235
Phone : 1 805 522 7958 Fax : 1 805 522 3217 http://www.hirose.com UNITED KINGDOM: HIROSE ELECTRIC UK LTD. Crownhill Business Centre 22 Vincent Avenue Crownhill, Milton Keynes MK8 OAB Phone : 44 1908 305400 Fax : 44 1908 305401 http://www.hirose.co.uk HONG KONG: HIROSE ELECTRIC CO., LTD. Unit 506, Energy Plaza. 92 Granville Road, Tsim Sha Tsui East, Kowloon Phone : 852 2803 5338 Fax : 852 2591 6560 EUROPE BRANCH: HIROSE ELECTRIC CO., LTD. Beechavenue 46.1119PV Schiphol-Rijk,The Netherlands Phone : 31 20 6557460 Fax : 31 20 6557469 http://hiroseeurope.com KOREA: HIROSE KOREA CO., LTD. (#2NA311,Shihwa Industrial Complex), 1261-10, Jeoungwhang-Dong, Shihung-City, Kyunggi-Do Phone : 82 31 496 7000,7124 Fax : 82 31 496 7100 http://www.hirose.co.kr TAIWAN: HIROSE ELECTRIC CO., LTD. No.28 Lane 247 Sec. 2 Yen Ping N,Rd.Taipei Phone : 886 2 2557 7351,7352 Fax : 886 2 2552 9851 GERMANY: HIROSE ELECTRIC GmbH Zeppelinstrasse 42 D-73760 Ostfildern Kemnat Phone : 49 711 4560021 Fax : 49 711 4560729 http://www.hirose.de CHINA: HIROSE ELECTRIC TRADING(SHANGHAI) CO., LTD. 3705,Bund Center,222 Yan An Road(E),Shanghai 20002 Phone : 86 21 6335 2538 Fax : 86 21 6335 0767 SINGAPORE: HIROSE ELECTRIC CO., LTD.
10 Anson Road #34-13 International Plaza 079903
Phone : 65 6324 6113 Fax : 65 6324 6123 5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933