HRF-SW1000 HONEYWELL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

Features

  • High Isolation Of > 40 dB @ 2 GHz
  • Low Insertion Loss Of 1.1dB @ 2 GHz
  • DC To 4GHz Operating Frequency
  • Integrated CMOS Control Logic
  • Integrated ESD Protection on Digital I/O
  • Single Positive Supply Voltage
  • Ultra Small LPCCTM Packaging
  • Impedance matched for 50 Ohm systems Product Description The Honeywell HRF-SW1000 is a high performance single pole double throw (SPDT) absorptive RF switch that is ideal for use in wireless basestation and handset applications that require minimum power and minimum insertion loss. The HRF-SW1000 is manufactured with Honeywell's patented Silicon On Insulator (SOI) CMOS technology, which provides the performance of GaAs with the economy and integration capabilities of conventional CMOS technology. oC Results @ Vdd=5.0 =/- 10%, Vss = 0 unless otherwise stated, Z0=50 ohms Parameter Test Condition Frequency Minimum Typical Maximum Units Insertion Loss DC – 0.5 GHz

2.0 GHz

3.0 GHz

0.9 1.1 1.3 1.2 1.5 1.7 dB dB dB Isolation DC – 0.5 GHz 53.5 42.5 39.0 dB dB dB VSWR* DC – 0.5 GHz 1.1:1 1.2:1 1.2:1 1.3:1 Ratio Ratio Ratio 1dB Compression Input Power Vss=Gnd Vss= -3

1.0 GHz

Input IP3 Two-Tone Inputs Up To + 5 dBm Vss=Gnd Vss= -3 Trise, Tfall* Ton, Toff Transients 10% To 90% 50% Cntl To 90%/10%Rf In-Band nS nS mV *By design HRF-SW1000 in LPCC™ Package

Web Site: www.mysoiservices.com Honeywell Email: mysoiservices@honeywell.com Solid State Electronics Center

12001 State Highway 55

2002 1000W Published June 2002 Page 2 Plymouth, Minnesota 55441-4799 1-800-323-8295 Parameter Minimum Typical Maximum Units Single VDD Supply Voltage 3.3* 5.0 5.5 V CMOS Logic Level (0) 0 0.8 V CMOS Logic Level (1) V DD – 0.8 V DD V Input Leakage Current 10 uA * Performance curves are for Vdd = +5.0 +/- 10% Absolute Maximum Ratings1 Parameter Absolute Maximum Units VDD +6.0 V Vin Digital Logic 0 Vss - 0.6 V Vin Digital Logic 1 Vdd + 0.6 V Maximum Input Power > 35 dBm ESD Voltage 400 V Operating Temperature Range +85 Degrees C Storage Temperature Range +125 Degrees C (Note 1) Operation beyond any of these parameters may cause permanent damage. Latch-Up: Unlike conventional CMOS RF switches, Honeywell's HRF-SW1000 is immune to latch-up. ESD Protection: Although this device contains ESD protection circuitry on all digital inputs, conventional precautions should be taken to ensure that the Absolute Maximum Ratings are not exceeded. Package Outline Drawing Bottom View

12 Pin 3X3 mm LPCCTM Package

ASAT LPCC Marketing Outline Dwg. # GMJ00004 For more information see http://www.asat.com 3 mm 3 mm

Web Site: www.mysoiservices.com Honeywell Email: mysoiservices@honeywell.com Solid State Electronics Center 2002 1000W Published June 2002 Page 3 Plymouth, Minnesota 55441-4799 1-800-323-8295 Truth Table Switch Control RF Output 1 RF Output 2 RF INPUT - - - - - - RF INPUT "0" = CMOS Low, "1” = CMOS High Pin Configuration Pin Function Pin Function

1 GROUND 7 GROUND

2 RF OUT 2 8 RF OUT 1

3 GROUND 9 GROUND

4 VDD 10 GROUND

5 SWITCH CONTROL 11 RF IN

6 VSS 12 GROUND

Evaluation Circuit Board Connections HRF-SW1000 Evaluation Board Top View Honeywell HRF-SW1000 Open VDD SW Control VSS Ground RF Out2 RF Out1 RF In

Web Site: www.mysoiservices.com Honeywell Email: mysoiservices@honeywell.com Solid State Electronics Center 2002 1000W Published June 2002 Page 4 Plymouth, Minnesota 55441-4799 1-800-323-8295 Performance Curves Insertion Loss Isolation Isolation versus Frequency -100.00 -90.00 -80.00 -70.00 -60.00 -50.00 -40.00 -30.00 -20.00 00 . 511 . 522 . 53 Frequency (GHz) (dB) The Insertion Loss curve shows the worst case loss versus frequency at Vdd = +5.0 +/- 10%, Ta = 25C, Z0 = 50 Ohms The Isolation curve shows the typical isolation of an “off” state output to the insertion path. Insertion Loss versus Frequency -10 01234 Frequency Insertion Loss (dB)

Web Site: www.mysoiservices.com Honeywell Email: mysoiservices@honeywell.com Solid State Electronics Center 2002 1000W Published June 2002 Page 5 Plymouth, Minnesota 55441-4799 1-800-323-8295 Return Loss Evaluation Circuit Board Input / Output Return Losses versus Frequency -50.00 -45.00 -40.00 -35.00 -30.00 -25.00 -20.00 -15.00 -10.00 -5.00 0.00 00 . 511 . 522 . 53 Frequency (GHz) Return Loss (dB) The return loss curve shows the input return loss S11, the output return loss in the insertion path S22, and the output return loss in the isolation state S33. Honeywell's evaluation board provides an easy to use method of evaluatin g the RF performance of our switch. Simply connect power, DC and RF si gnals to be measurin g switch performance in less than 10 minutes. HRF-SW1000 Evaluation Board

Web Site: www.mysoiservices.com Honeywell Email: mysoiservices@honeywell.com Solid State Electronics Center 2002 1000W Published June 2002 Page 6 Plymouth, Minnesota 55441-4799 1-800-323-8295 Evaluation Circuit Board Layout Design Details

Ordering Information

Delivered On Tape And Reel Engineering Evaluation Board (Note 2) Contact Honeywell for details LPCCTM is a registered Trademark of ASAT Ltd. Honeywell reserves the right to make changes to improve reliability, function or design. Honeywell does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. Item Description PCB Impedance Matched Multi-Layer FR4 Switch HRF-SW1000 RF Switch Chip Capacitor Panasonic Model ECU-E1C103KBQ Capacitor, .01uf 0402 10% 16V RF Connector Johnson Connectors Model 142-0701-801 SMA RF Coaxial Connector DC Pin Mil-Max Model 800-10-064-10-001 Header Pins