HR152-2812

HR151-2812 CRANE | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

Features

• –40°C to +85°C operation
• 10 to 16 VDC input or 18 to 36 VDC input
• Fully Isolated
• Optocoupler feedback
• Fixed frequency, 125 kHz typical single and dual outputs; 250 kHz typical triple outputs
• Transient protection 50 V for up to 50 ms 28 Vin models
• Inhibit function
• Indefinite short circuit protection
• Up to 86% efficiency
• Output trim on single output models models VDC Output SINgLE DUAL ±12 ±15 TRIPLE +5 & ±12 +5 & ±15 hr150 SerieS

20 WattDC/DC Converters

12 & 28 volt Input NOt RECOMMENDED FOR NEW DESIGNS

recommended operating conditions typical characteristics inhibit absolute maximum ratings input Voltage

• 10 to 16 VDC HR15X-12XX
• 18 to 36 VDC HR15X-28XX output power
• 15 watts (HR151-2812 & HR151-2815, 20 watts) lead soldering temperature (10 sec)
• 300°C storage temperature range (case)
• –55°C to +125°C output Voltage temperature coefficient
• 150 ppm/°C, typical input to output capacitance
• 60 pF, typical isolation
• 100 megohm minimum at 500 V conversion Frequency
• 250 kHz inhibit pin Voltage (unit enabled)
• 8 to 10 V HR15X-12XX models
• 11 to 13 V HR15X-28XX models line regulation
• 0.1% typical, 0.2% maximum load regulation
• 0.2% typical, 0.4% maximum input Voltage range
• 10 to 16 VDC continuous HR15X-12XX models
• 18 to 36 VDC continuous HR15X-28XX models
• 50 V/50 ms transient HR15XX-28XX models case operating temperature (tc)
• –40°C to +85°C full power
• –40°C to +105°C absolute derating output power/current
• Linearly from 100% at 85°C to 0% at 105°C for HR151 models
• Linearly from 100% at 85°C to 0% at 115°C for HR153 models inhibit ttl open collector
• Logic low (output disabled) Inhibit pin current 1 mA typical Inhibited input current 8 mA typical
• Referenced to input common
• Logic high (output enabled) Open collector Electrical Characteristics: 25°C Tc, 28 VDC Vin (12 Vin for 12V models), 100% load, unless otherwise specified. SINgLE OUTPUT MODELS, 12 V IN HR151-1205 HR151-1212 HR151-1215 UnitS PaRameteR conDitionS min tyP maX min tyP maX min tyP maX oUtPUt cURRent — — 3.0 — — 1.25 — — 1.0 A oUtPUt PoweR — — 15 — — 15 — — 15 W oUtPUt RiPPle 0 to 1 mHz — 35 70 — 35 70 — 35 70 mV p-p inPUt voltage continUoUS 10 12 16 10 12 16 10 12 16 VDC inPUt cURRent no loaD — — 24 — — 32 — — 32 mA inPUt RiPPle cURRent 0 to 2 mHz — 40 80 — 40 80 — 40 80 mA p-p efficiency 75 81 — 76 82 — 77 83 — % SINgLE OUTPUT MODELS, 28 V IN HR151-2805 HR151-2812 HR151-2815 UnitS PaRameteR conDitionS min tyP maX min tyP maX min tyP maX oUtPUt cURRent — — 3.0 — — 1.667 — — 1.333 A oUtPUt PoweR — — 15 — — 20 — — 20 W oUtPUt RiPPle 0 to 1 mHz — 30 60 — 40 80 — 40 80 mV p-p inPUt voltage continUoUS 18 28 36 — — 50 18 28 36 — — 50 18 28 36 — — 50 VDC VtRanSient 50 ms inPUt cURRent no loaD — — 20 — — 30 — — 30 mA inPUt RiPPle cURRent 0 to 2 mHz — 25 50 — 25 50 — 25 50 mA p-p efficiency 75 81 — 76 82 — 77 83 — % hr150 SerieS

Electrical Characteristics: 25°C Tc, 28 VDC Vin (12 VDC for 12V models), 100% load, unless otherwise specified. Notes 1. Minimum load required for full output capability on auxiliary outputs. Minimum current can be reduced when dual outputs are used at reduced loads. TRIPLE OUTPUT MODELS HR153-1212 HR153-1215 HR153-2812 HR153-2815 UnitS PaRameteR conDitionS min tyP maX min tyP maX min tyP maX min tyP maX oUtPUt voltage fUll loaD main 4.95 5.00 5.05 ±11.88 ±12 ±12.12 4.95 5.00 5.05 ±14.85 ±15 ±15.15 4.95 5.00 5.05 ±11.88 ±12 ±12.12 4.95 5.00 5.05 ±14.85 ±15 ±15.15 VDC DUal oUtPUt cURRent main1 100 — 2000 — — ±208 100 — 2000 — — ±167 100 — 2000 — — ±208 100 — 2000 — — ±167 mA DUal oUtPUt PoweR main — — 10 — — 2.5 — — 15 — — 10 — — 2.5 — — 15 — — 10 — — 2.5 — — 15 — — 10 — — 2.5 — — 15 W ±DUal total oUtPUt RiPPle 0 to 1 mHz main — 40 80 — 20 40 — 40 80 — 20 40 — 40 80 — 20 40 — 40 80 — 20 40 mV p-p DUal inPUt voltage continUoUS 10 22 16 — — 25 10 22 16 — — 25 18 28 36 — — 50 18 28 36 — — 50 VDC VtRanSient 50 ms inPUt cURRent no loaD — — 60 — — 60 — — 50 — — 50 mA inPUt Refl. RiPPle 0 to 2 mHz — 50 100 — 50 100 — 40 80 — 40 80 mA p-p efficiency 76 79 — 76 79 — 75 79 — 75 79 — % DUAL OUTPUTS HR152-2812 HR152-2815 PARAMETER CONDITION MIN TYP MAX MIN TYP MAX UNITS OUTPUT OUTPUT CURRENT 0 — ±625 0 — ±500 mA OUTPUT POWER — — 15 — — 15 W OUTPUT RIPPLE 0 TO 1 MHz — 30 50 — 30 50 mV p-p INPUT CONTINUOUS 18 28 36 18 28 36 VDC VOLTAgE TRANSIENT 50 ms — — 50 — — 50 V INPUT NO LOAD — — 35 — — 35 mA CURRENT INPUT REFL. — 25 50 — 25 50 mA p-p RIPPLE

0 TO 2 MHz

EFFICIENCY 75 79 — 75 79 — % hr150 SerieS

(1 = single, 2 = dual, 3 = triple) (Auxiliary output on triple output models) pin out BOTTOM VIEW HR151 and HR152 1 2 610 3 4 5 789 Dot on top of package indicates pin one BOTTOM VIEW HR153 10 9 8 7 6 1 2 3 4 5 Squared corner and dot on top of package indicate pin one. See case H6 for dimensions. See case F4 for dimensions. figURe 1: HR151 anD 152 Pin oUt figURe 2: HR153 Pin oUt Output ADJuStMENt RESIStOR VALuES FOR HR151-2805 Output Adjustment all HR151 models (single output): The output can be adjusted upward by using the output adjust (pin3). The resistance between output adjust (pin 3) and output common (pin 4) will determine the magnitude of the increase in the output. The table above is only applicable to HR151-2805. resistance output Voltage pin 3 to 4 increase (%) ∞ 0 390K +1% 145K +2% 63K +3% 22K +4% 0 +5% pin single output dual output triple output

1 Positive Input Positive Input Positive Input

2 Inhibit Inhibit Main (+5) Output

3 Trim Positive Output Output Common

4 Output Common Output Common Neg. Aux. Output 5 Positive Output Negative Output Pos. Aux. Output

6 No connection No connection No connection

7 No connection No connection Case ground

8 Case ground Case ground Inhibit

9 No connection No connection No connection

10 Input Common Input Common Input Common

0.000 0.173 (4.39) 1.173 (29.79) 0.000 0.170 (4.32) 0.570 (14.48) 0.970 (24.64) 1.370 (34.80) 1.770 (44.96) 0.040 dia. (1.02) 0.000 MTO Series and HR153 Series BOTTOM VIEW CASE F4 0.250/0.300 (6.35/7.62) Solder Seal 0.505 max (12.83) Solder Tip-off 10 9 8 7 6 1 2 3 4 5 Squared corner and dot on top of case indicate pin one. Seal hole: 0.083 ±0.003 (2.11 ±0.08) Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Case F4, Rev B, September 21, 2005 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2005 Interpoint Corp. All rights reserved. figURe 3: caSe f4 – HR153 hr150 SerieS

0.160 (4.06) 0.960 (24.38) 0.655 (16.64) 1.055 (26.80) 1.455 (36.96) 0.000 0.000 0.255 (6.48) 1.855 (47.12) 2.110 max (53.59) 1.120 max (28.45) 1 2 610 BOTTOM VIEW CASE H6 3 4 5 789 0.040 dia (1.02) 0.25 +0.05/-0.00 (6.4 +1.3/-0.0) Solder Seal Solder Tip-off 0.000 0.495 max (12.57) Dot on top of case indicates pin one Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Tin Cover Cold Rolled Steel/Nickel/Tin Pins #52 alloy, compression glass seal or ceramic seal Case H6, Rev C, 20060802 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2006 Interpoint Corp. All rights reserved. figURe 4: caSe H6 – HR151 anD HR152 hr150 SerieS

Hr InDustrIal non-QMl proDuCts — envIronMental sCreenIng test Hr industrial standard non Qml1 Pre-cap Inspection Method 2017 yes Final Electrical Test MIL-PRF-38534, group A Subgroups 1 and 4: +25°C case yes Hermeticity Test gross Leak, Dip (1 x 10 -3) yes Final Visual Inspection Method 2009 yes Test methods are referenced to MIL-STD-883 as determined by MIL- PRF-38534. Notes: 1. Non-QML products do not meet all of the requirements of MIL-PRF-38534 hr150 SerieS HR151, 152 and 153 Rev C 20061030 All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. HR150 Series is a trademark of Interpoint. Copyright © 1991 - 2006 Interpoint. All rights reserved. 7