HR150 INTERPOINT | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

Features

  • -40°C to +85°C operation
  • 18 to 36 VDC input
  • Transient protection 50 V for 50 ms for 28 Vin models
  • Fully isolated
  • Fixed frequency switching
  • Output trim on single output models
  • Inhibit function
  • Indefinite short circuit protection
  • Up to 86% efficiency mODELS VDc outPut Si n g l e Dual ±12 ±15 tRiPle +5 & ±12 +5 & ±15 HR150 SERIES

20 WATT

28 Vo l t inPut

NOT RECOMMENDED FOR NEW DESIGNS Page 1 of 7 HR150 Rev E 20100212 Crane Aerospace & Electronics Electronics Group (Interpoint Brand) PO Box 97005 • Redmond WA 98073-9705 425.882.3100 • power@crane-eg.com www.interpoint.com

recommended operating conditions typical characteristics inhibit absolute maximum ratings input Voltage

  • 18 to 36 VDC output power
  • 15 watts (HR151-2812 & HR151-2815, 20 watts) Lead soldering temperature (10 sec)
  • 300°C storage temperature range (case)
  • –55°C to +125°C output Voltage temperature coefficient
  • 150 ppm/°C, typical input to output capacitance
  • 60 pF, typical isolation
  • 100 megohm minimum at 500 V conversion Frequency
  • 250 kHz inhibit pin Voltage (unit enabled)
  • 11 to 13 V HR15X-28XX models Line regulation
  • 0.1% typical, 0.2% maximum Load regulation
  • 0.2% typical, 0.4% maximum input Voltage range
  • 18 to 36 VDC continuous
  • 50 V/50 ms transient case operating temperature (tc)
  • –40°C to +85°C full power
  • –40°C to +105°C absolute derating output power/current
  • Linearly from 100% at 85°C to 0% at 105°C for HR151 and HR152 models
  • Linearly from 100% at 85°C to 0% at 115°C for HR153 models inhibit ttL open collector
  • Logic low (output disabled) Inhibit pin current 1 mA typical Inhibited input current 8 mA typical
  • Referenced to input common
  • Logic high (output enabled) Open collector Electrical Characteristics: 25°C Tc, 28 VDC Vin, 100% load, unless otherwise specified. sIngLe OUTPUT mODeLs, 28 V In HR151-2805 HR151-2812 HR151-2815 unitS PaRameteR conDitionS min tyP maX min tyP maX min tyP maX outPut cuRRent — — 3.0 — — 1.667 — — 1.333 A outPut PoweR — — 15 — — 20 — — 20 W outPut RiPPle 0 to 1 mHz — 30 60 — 40 80 — 40 80 mV p-p inPut Vo l t a g e continuouS 18 28 36 — — 50 18 28 36 — — 50 18 28 36 — — 50 VDC V tRanSient 50 ms inPut cuRRent no l o aD — — 20 — — 30 — — 30 mA inPut RiPPle cuRRent 0 to 2 mHz — 25 50 — 25 50 — 25 50 mA p-p efficiency 75 81 — 76 82 — 77 83 — % HR150 SERIES

www.interpoint.com

Electrical Characteristics: 25°C Tc, 28 VDC Vin, 100% load, unless otherwise specified. Notes 1. minimum load required for full output capability on auxiliary outputs. minimum current can be reduced when dual outputs are used at reduced loads. DUAL OUTPUT mODeLs HR152-2812 HR152-2815 unitS PaRameteR conDitionS min tyP maX min tyP maX outPut Vo l t a g e ±11.88 ±12 ±12.12 ±14.85 ±15 ±15.15 VDC outPut cuRRent — — ±625 — — ±500 mA outPut PoweR — — 15 — — 15 W outPut RiPPle 0 to 1 mHz — 30 50 — 30 50 mV p-p inPut Vo l t a g e continuouS 18 28 36 — — 50 18 28 36 — — 50 VDC V tRanSient 50 ms inPut cuRRent no l o aD — — 35 — — 35 mA inPut RiPPle cuRRent 0 to 2 mHz — 25 50 — 25 50 mA p-p efficiency 75 79 — 75 79 — % TRIPLe OUTPUT mODeLs HR153-2812 HR153-2815 unitS PaRameteR conDitionS min tyP maX min tyP maX outPut Vo l t a g e full l o aD m a i n 4.95 5.00 5.05 ±11.88 ±12 ±12.12 4.95 5.00 5.05 ±14.85 ±15 ±15.15 VDC Dual outPut cuRRent m a i n1 100 — 2000 — — ±208 100 — 2000 — — ±167 mA Dual outPut PoweR m a i n — — 10 — — 2.5 — — 15 — — 10 — — 2.5 — — 15 W Dual total outPut RiPPle 0 to 1 mHz m a i n — 40 80 — 20 40 — 40 80 — 20 40 mV p-p Dual inPut Vo l t a g e continuouS 18 28 36 — — 50 18 28 36 — — 50 VDC V tRanSient 50 ms inPut cuRRent no l o aD — — 50 — — 50 mA inPut RiPPle cuRRent 0 to 2 mHz — 40 80 — 40 80 mA p-p efficiency 75 79 — 75 79 — % HR150 SERIES www.interpoint.com

(1 = single, 2 = dual, 3 = triple) (Auxiliary output on triple output models) pin out BOTTOM VIEW HR151 and HR152 610 345 789 Dot on top of package indicates pin one BOTTOM VIEW HR153 10 987 6 1234 5 Squared corner and dot on top of package indicate pin one. See case H6 for dimensions. See case F4 for dimensions. figuRe 1: HR151 anD HR152 Pin out figuRe 2: HR153 Pin out pin single output dual output triple output

1 Positive Input Positive Input Positive Input

2 Inhibit Inhibit main (+5) Output

3 Trim Positive Output Output Common

4 Output Common Output Common Neg. Aux. Output 5 Positive Output Negative Output Pos. Aux. Output

6 No connection No connection No connection

7 No connection No connection Case Ground

8 Case Ground Case Ground Inhibit

9 No connection No connection No connection

10 Input Common Input Common Input Common

OUTPUT ADJUSTMENT RESISTOR VALUES F O R HR151-2805 Output Adjustment all HR151 models (single output): The output can be adjusted upward by using the output adjust (pin3). The resistance between output adjust (pin 3) and output common (pin 4) will determine the magnitude of the increase in the output. The table above is only applicable to HR151-2805. resistance output Voltage pin 3 to 4 increase (%) ∞ 0 390K +1% 145K +2% 63K +3% 22K +4% 0 +5% HR150 SERIES www.interpoint.com

0.000 0.173 (4.39) 1.173 (29.79) 0.000 0.170 (4.32) 0.570 (14.48) 0.970 (24.64) 1.370 (34.80) 1.770 (44.96) 0.040 dia. (1.02) 0.000 BOTTOM VIEW CASE F4 0.250/0.300 (6.35/7.62) Solder Seal 0.505 max (12.83) Solder Tip-off 10 9 8 7 6 1 2 3 4 5 Squared corner and dot on top of case indicate pin one. Seal hole: 0.083 ±0.003 (2.11 ±0.08) Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Tin Cover Cold Rolled Steel/Nickel/Tin Pins #52 alloy, compression glass seal or ceramic seal Case F4, Rev C, 20060802 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2006 Interpoint Corp. All rights reserved. 1.950 max (49.53) 1.350 max (4.39) figuRe 3: caSe f4 – HR153 HR150 SERIES www.interpoint.com

0.160 (4.06) 0.960 (24.38) 0.655 (16.64) 1.055 (26.80) 1.455 (36.96) 0.000 0.000 0.255 (6.48) 1.855 (47.12) 2.110 (53.59) 1.120 (28.45) 1 2 610 BOTTOM VIEW CASE H6 3 4 5 789 0.040 dia (1.02) 0.25 +0.05/-0.00 (6.4 +1.3/-0.0) Solder Seal Solder Tip-off 0.000 0.495 max (12.57) Dot on top of case indicates pin one Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Tin Cover Cold Rolled Steel/Nickel/Tin Pins #52 alloy, compression glass seal or ceramic seal Case H6, Rev D, 20100211 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2010 Interpoint Corp. All rights reserved. figuRe 4: caSe H6 – HR151 anD HR152 HR150 SERIES www.interpoint.com

HR IN D U S T R I A L (ST A N D A R D, N O N-QML) PR O D U C T S EN V I R O N M E N T A L SC R E E N I N G test perFormed hr industrial standard non-Qml1 Pre-cap Inspection Method 2017, 2032 yes Final Electrical Test MIL-PRF-38534, Group A Subgroups 1 and 4: +25°C case yes Hermeticity Test Gross Leak, Dip (1 x 10 -3) yes Final visual inspection Method 2009 yes Test methods are referenced to mIL-STD-883 as determined by mIL-PRF-38534. Notes: 1. Standard, non-QmL products, do not meet all of the requirements of mIL-PRF-38534. HR150 SERIES HR150 Series DC/DC Converters, HR150 Rev E 20100212. This revision supersedes all previous releases. All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without