HR10 HIROSE | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 21
Technical content
Features
- A simple, yet highly reliable design for compact, high density applications Although small in size, the HR10 series are full featured connectors with a well integrated design. 2. Extremely easy mating/unmating operations Easy to operable, the single-action push-pull lock structure allows for quick and efficient locking and unlocking. Product Specifi cations Ratings Shell size No. of contacts Rated current 10 10 12 2A 13 20 2A Ratings Shell size No. of contacts Rated voltage AC150V, DC200V AC100V, DC140V AC100V, DC140V 10 10
12 AC100V, DC140V
13 20 AC100V, DC140V Ratings Operation temperature range -25 to +85ç Storage temperature range -10 to +60ç Items Specifications Conditions 1. Contact resistance 10mø min. Measured at DC 1A 2. Insulation resistance 1,000Mø min. Measured at DC 100V 3. Withstanding voltage No flashover or dielectric breakdown. AC 300V for one minute, 4 contacts : AC 500V for 1 minute 4. Vibration resistance No electrical discontinuity of 10µs or greater 10 to 55Hz/cycle, amplitude : 0.75mm, 3 axis directions, for 2 hours each 5. Shock resistance No electrical discontinuity of 10µs or greater Acceleration : 490m/s 2, duration : 11ms 3 directions, 3 times each 6. Mating Cycles Contact resistance : 15mø min. 1,000 times 7. Temperature cycle Insulation resistance : 1,000Mø min. -55ç : 30minutes➝Normal temperature : 10 to 15 minutes➝ 85ç : 30minutes ➝Normal temperature : 10 to 15minutes, left for 5 cycles. 8. Humidity resistance 5Mø min. (at high humidity) 50Mø min. (at dry) Temperature : 40ç, relative humidity : 90 to 95%, left for 96 hours In cases where the application will demand a high level of reliability, such as automotive, please contact a company representative for further information. 1
Items Material Finish Remarks Contact Copper alloy HR10 : Gold plating qModel name : Indicates the HR10A Series. The part type is identified as follows. HR10A : Lower cost type HR10G : Shield type HR10B : Coaxial contact type wShell size : The shell size is the outer shell diameter or the mating interface end of the plug. eShell type P : Plug R : Receptacle J : Jack rNumber of contacts tContact form P : Male contact S : Female contact yContact termination method: None : Solder termination C : Crimp termination uOther specifications : A two-digit character is added to indicate other specifications as needed. Product Number Structure Refer to the chart below when determining the product specifications from the product number. Please select from the product numbers listed in this catalog when placing orders. HR10A - 7P - 3PC (**) qw e r t y u HR10 Series●High performance miniature circular connectors
Diagrams of Connectors in Combination Notes 1 : When using a plug with male terminal, be sure to use a receptacle or jack fi tted with female terminal. 2 : Standard fi nish of the terminal is gold plating for the HR10, and silver plating for the HR10A and HR10G. Be sure to use male and female connectors of the same plating. Male Pin side Female Pin side (HR10 Type Plug) (HR10 Type Jack) (HR10B Type Receptacle) (HR10A-[ ]T Type Receptacle) (HR10A-[ ]T Type Jack) (HR10A Type Jack) (HR10 • HR10A HR10G Type Receptacle) (HR10A Type Plug) (HR10B Type Plug) (HR10A-[ ]T Type Plug) HR10 Series●High performance miniature circular connectors
HR10 type connectors, use a gold plated contact as the standard plating specification. Silver plating is used on the contacts for other series such as HR10A and HR10G. To avoid mixing gold and silver contacts, please be sure to confirm the plating specification when using HR10 type connectors with HR10A or HR10G connectors. Plug ØD A Max ØC ØB Unit : mm Part No. HRS No. No. of Contacts A ØB ØC ØD Weight HR10-7P-4P(73) 110-0021-6 73 28.5 11 7 5.2 8g HR10-7P-4S(73) 110-0022-9 73 HR10-7P-6P(73) 110-0023-1 73 HR10-7P-6S(73) 110-0024-4 73 HR10-10P-12P(73) 110-0025-7 73 12 32.5 14 9.5 7.2 15g HR10-10P-12S(73) 110-0026-0 73 (Representative example)HR10-7P-6S(73) Receptacle E(HEX) D A 5.76.3 ØC ØB Unit : mm Part No. HRS No. No. of Contacts A ØB ØC D E Weight HR10-7R-4S(73) 110-0031-0 73 14 11 8.85 M8×0.5 10 3.5g HR10-7R-4P(73) 110-0032-2 73 HR10-7R-6S(73) 110-0033-5 73 HR10-7R-6P(73) 110-0034-8 73 HR10-10R-12S(73) 110-0035-0 73 12 16 14 11.9 M11×0.75 13 6g HR10-10R-12P(73) 110-0036-3 73 Remarks : For mounting holes, see page 20. (Representative example)HR10-7R-6S(73) HR10 Series●High performance miniature circular connectors
Receptacle (PCB dip type) D(HEX) C Dip post dia. Ø0.55 G F5.7E ØA ØB Unit : mm Part No. HRS No. No. of Contacts ØA ØB C D E F G Weight HR10-7R-4SA(73) 110-0059-9 73 4 11 8.85 M8×0.5 10 6.3 0.5 15.5 3gHR10-7R-6SA(73) 110-0050-4 73 HR10-7R-6PA(73) 110-0061-0 73 HR10-10R-12SA(73) 110-0049-5 73 12 14 11.9 M11×0.75 13 5g HR10-10R-12PA(73) 110-0055-8 73 Remarks : 1. For mounting holes, see page 20. 2. For dip post arrangement, see page 16. (Representative example) HR10-7R-6SA(73) Jack ØD 5.5 A Max ØB ØC Unit : mm Part No. HRS No. No. of Contacts A ØB ØC ØD Weight HR10-7J-4S(73) 110-0027-2 73 28.5 11 8.85 5.2 7g HR10-7J-4P(73) 110-0028-5 73 HR10-7J-6S(73) 110-0029-8 73 HR10-7J-6P(73) 110-0030-7 73 HR10-10J-12S(73) 110-0037-6 73 12 32.5 14 11.9 7.2 14g HR10-10J-12P(73) 110-0038-9 73 (Representative example) HR10-7J-6S(73) HR10 Series●High performance miniature circular connectors
Plug (Solder type) ØB ØC ØD A Unit : mm Part No. HRS No. No. of Contacts A ØB ØC ØD Weight HR10A-7P-4P(73) 110-0301-2 73 4 35 11.5 7 5 9g HR10A-7P-4S(73) 110-0302-5 73 HR10A-7P-5P(73) 110-0318-5 73 5HR10A-7P-5S(73) 110-0319-8 73 HR10A-7P-6P(73) 110-0303-8 73 6HR10A-7P-6S(73) 110-0304-0 73 HR10A-10P-10P(73) 110-0407-3 73 10 43 14.7 9.5 16gHR10A-10P-10S(73) 110-0408-6 73 HR10A-10P-12P(73) 110-0401-7 73 12HR10A-10P-12S(73) 110-0402-0 73 HR10A-13P-20P(73) 110-0713-0 73 20 59 19 13 37gHR10A-13P-20S(73) 110-0716-8 73 (Representative example) HR10A-7P-6P(73) Plug(Crimp type) ØC ØB ØD A Unit : mm Part No. HRS No. No. of Contacts A ØB ØC ØD Weight HR10A-7P-4PC(73) 110-0501-1 73 4 35 11.5 7 5 9gHR10A-7P-4SC(73) 110-0502-4 73 HR10A-7P-6PC(73) 110-0503-7 73 6HR10A-7P-6SC(73) 110-0504-0 73 HR10A-10P-10PC(73) 110-0601-6 73 10 43 14.7 9.5 16gHR10A-10P-10SC(73) 110-0602-9 73 HR10A-10P-12PC(73) 110-0603-1 73 12HR10A-10P-12SC(73) 110-0604-4 73 HR10A-13P-20PC(73) 110-0701-0 73 20 59 19 13 37gHR10A-13P-20SC(73) 110-0702-3 73 (Representative example)HR10A-7P-6PC(73) HR10A•10G Types HR10A connectors are a lower-cost version, yet still provide a high "Value Add" while preserving the superior characteristics of the HR10 connectors. Cable clamps are crimped using a special crimping tool, and the shells have a rubber boot which provides a flexible design that helps to prevent cable twisting. The HR10G connector is a shielded type connector which has an internal contacting structure between the plug shell and receptacle shell. Contacts in both HR10A and 10G connectors are silver plated as standard. HR10 Series●High performance miniature circular connectors
Unit : mm Part No. HRS No. No. of Contacts ØA ØB C D E F Weight Remarks HR10A-7R-4SC(73) 110-0506-5 73 4 11 8.85 M8×0.5 10 6.3 3gHR10A-7R-4PC(73) 110-0505-2 73 12.2 HR10A-7R-6SC(73) 110-0508-0 73 6 12 HR10A-7R-6PC(73) 110-0507-8 73 12.2 HR10A-10R-10SC(71) 110-0606-0 71 10 14 11.9 M11×0.75 13 5gHR10A-10R-10PC(71) 110-0605-7 71 12.2 HR10A-10R-12SC(71) 110-0608-5 71 12 12 HR10A-10R-12PC(71) 110-0607-2 71 12.2 HR10A-13R-20SC(73) 110-0703-6 73 20 18 15.4 M14×0.75 17 9.3 15 8gHR10A-13R-20PC(73) 110-0704-9 73 HR10G-7R-4SC(73) 110-1701-6 73 4 11 8.85 M8×0.5 10 6.3 Shield type HR10G-7R-4PC(73) 110-1702-9 73 12.2 HR10G-7R-6SC(73) 110-1705-7 73 6 12 HR10G-7R-6PC(73) 110-1706-0 73 12.2 HR10G-10R-10SC(71) 110-1707-2 71 10 14 11.9 M11×0.75 13 5gHR10G-10R-10PC(71) 110-1708-5 71 12.2 HR10G-10R-12SC(71) 110-1709-8 71 12 12 HR10G-10R-12PC(71) 110-1710-7 71 12.2 HR10G-13R-20SC(73) 110-1711-0 73 20 18 15.4 M14×0.75 17 9.3 15 8gHR10G-13R-20PC(73) 110-1712-2 73 Remarks : For mounting holes, see page 20. Receptacle (Solder type) E(HEX) D ØB ØC A 5.7F (Representative example) Unit : mm Part No. HRS No. No. of Contacts AØ BØ C D EE Weight Remarks HR10A-7R-4S(73) 110-0305-3 73 4 14 11 8.85 M8×0.5 10 6.3 HR10A-7R-4P(73) 110-0306-6 73 HR10A-7R-5S(73) 110-0320-7 73 5HR10A-7R-5P(73) 110-0321-0 73 HR10A-7R-6S(73) 110-0307-9 73 6HR10A-7R-6P(73) 110-0308-1 73 HR10A-10R-10S(71) 110-0409-9 71 10 16 14 11.9 M11×0.75 13 5gHR10A-10R-10P(73) 110-0410-8 73 HR10A-10R-12S(71) 110-0403-2 71 12HR10A-10R-12P(73) 110-0404-5 73 HR10G-7R-4S(73) 110-1601-1 73 4 14 11 8.85 M8×0.5 10 6.3 Shield type HR10G-7R-4P(73) 110-1602-4 73 HR10G-7R-6S(73) 110-1605-2 73 6HR10G-7R-6P(73) 110-1606-5 73 HR10G-10R-10S(71) 110-1607-8 71 10 16 14 11.9 M11×0.75 13 5gHR10G-10R-10P(73) 110-1608-0 73 HR10G-10R-12S(71) 110-1609-3 71 12HR10G-10R-12P(73) 110-1610-2 73 Remarks : For mounting holes, see page 20. HR10A-7R-6S(73) Receptacle (Crimp type) C D(HEX) E F ØB ØA (Representative example)HR10A-10R-12SC(71) HR10 Series●High performance miniature circular connectors
B ØA 0.2ØD ØC ØE HR10-7R-C Receptacle (Dip type) D(HEX) C Dip post dia. 0.2∞0.5 ØA ØB G F5.7E Unit : mm Part No. HRS No. No. of Contacts ØA ØB C D E F G Weight Remarks HR10A-7R-4SB(73) 110-0314-4 73 4 11 8.85 M8×0.5 10 6.3 0.5 15.6 3gHR10A-7R-4PB(73) 110-0315-7 73 HR10A-7R-5SB(73) 110-0322-2 73 5 HR10A-7R-6SB(73) 110-0316-0 73 6HR10A-7R-6PB(73) 110-0317-2 73 HR10A-10R-10SB(71) 110-0413-6 71 10 14 11.9 M11×0.75 13HR10A-10R-10PB(71) 110-0414-9 71 HR10A-10R-12SB(71) 110-0415-1 71 12HR10A-10R-12PB(71) 110-0416-4 71 HR10A-13R-20SB(73) 110-0707-7 73 20 18 15.4 M14×0.75 17 9.3 0 17.8 8gHR10A-13R-20PB(73) 110-0708-0 73 HR10G-7R-4SB(73) 110-1801-0 73 4 11 8.85 M8×0.5 10 6.3 0.5 15.6 Shield type HR10G-7R-4PB(73) 110-1802-3 73 HR10G-7R-6SB(73) 110-1805-1 73 6HR10G-7R-6PB(73) 110-1806-4 73 HR10G-10R-10SB(71) 110-1807-7 71 10 14 11.9 M11×0.75 13 5gHR10G-10R-10PB(71) 110-1808-0 71 HR10G-10R-12SB(71) 110-1809-2 71 12HR10G-10R-12PB(71) 110-1810-1 71 HR10G-13R-20SB(73) 110-1811-4 73 20 18 15.4 M14×0.75 17 9.3 0 17.8 8gHR10G-13R-20PB(73) 110-1812-7 73 Remarks : 1. For mounting holes, see page 20. 2. For dip post arrangement, see page 16. Unit : mm Part No. HRS No. ØA B ØC ØD ØE HR10-7R-C 110-0058-6 00 11 7 8 11.2 13 HR10-10R-C 110-0052-0 00 14 8.5 10.8 14.1 15 HR10A-13R-C 110-0452-8 00 17.5 11.5 14 18.1 19 (Representative example) (Representative example) HR10A-7R-6SB(73) HR10 Series●High performance miniature circular connectors
Jack (Solder type) ØC ØB 5.5 A ØD (Representative example) Unit : mm Part No. HRS No. No. of Contacts A ØB ØC ØD Weight HR10A-7J-4S(73) 110-0309-4 73 35.3 11 8.85 5 9g HR10A-7J-4P(73) 110-0310-3 73 HR10A-7J-6S(73) 110-0311-6 73 HR10A-7J-6P(73) 110-0312-9 73 HR10A-10J-10S(73) 110-0411-0 73 43.5 14 11.9 7 16g HR10A-10J-10P(73) 110-0412-3 73 HR10A-10J-12S(73) 110-0405-8 73 HR10A-10J-12P(73) 110-0406-0 73 HR10A-7J-6S(73) Jack (Crimp type) ØC ØB D A ØE Unit : mm Part No. HRS No. No. of Contacts A ØB ØC D ØE Weight HR10A-7J-4SC(73) 110-0510-2 73 4 35.3 11 8.85 5.5 59 g HR10A-7J-6SC(73) 110-0512-8 73 6 HR10A-10J-10SC(73) 110-0610-7 73 10 43.5 14 11.9 16g HR10A-10J-12SC(73) 110-0612-2 73 12 HR10A-13J-20SC(73) 110-0705-1 73 20 58.5 18 15.4 8.5 37g HR10A-13J-20PC(73) 110-0706-4 73 (Representative example)HR10A-7J-6SC(73) HR10 Series●High performance miniature circular connectors
The HR10B connector combines 10 signal lines and one coaxial contact in the standard number 10 shell. Performance specifications for the coaxial contacts are on the 11 page. Ø14.7 A ØB Unit : mm Part No. HRS No. A ØB Applicable coaxial contact HR10B-10P-10PC(73) 110-0901-0 73 50 5 HR10B-2.5CJ(73) HR10B-10PA-10PC(73) 110-0906-3 73 43 7 (Representative example)HR10B-10P-10PC(73) Receptacle 13(HEX) M11∞0.75 Ø11.9 Ø14 6.3 Unit : mm Part No. HRS No. Applicable coaxial contact HR10B-10R-10SC(71) 110-0902-2 71 HR10B-2.5CP(73) Remarks : For mounting holes, see page 20. (Representative example)HR10B-10R-10SC(71) HR10 Series●High performance miniature circular connectors
(clamp) 4.1 5.2 3.6 Ø3.8 7.1 18.05 Ø4.2 Ø1.1 (Representative example) Unit : mm Part No. HRS No. Applicable cable Applicable connector HR10B-2.5CP(73) 110-0904-8 73 0.8D-QEW-CW(By Fjikura wire) HR10B-10R-10SC(71) HR10B-2.5CP(73) Jack (clamp) Ø2.65 7.25 18.2 Ø4.2 Ø1.1 4.1 5.2 3.6 (Representative example) Unit : mm Part No. HRS No. Applicable cable Applicable connector HR10B-2.5CJ(73) 110-0903-5 73 0.8D-QEW-CW(By Fjikura wire) HR10B-10P-10PC(73) HR10B-2.5CJ(73) Coaxial contacts The coaxial contacts shown here are for use with the HR10B connector.These contacts have locking barbs and are inserted from the rear of connector.Please use the following information to select the correct terminals. Materials / Finish Performance Part Material Finish Plug shell Brass Gold plating Jack shell Insulator Tetrafl uoride resin Male pin Phosphor bronze Gold plating Female pin Beryllium copper Description Test data Impedance 50ø Insulation resistance 1000Mø or more at DC250V Contact resistance Center 6.5mø or less and outer 4mø or less at DC1A Withstanding voltage AC250V r.m.s for 1minute V.S.W.R 1.3 or less for 0 to 1000MHz Pull force 4.9N (500gf) or more HR10 Series●High performance miniature circular connectors
11±0.5 1.4±0.2 3.7±0.2(2.5) Slit cable outer jaket 2 pieces (180° reverse side) 1. Dimensions for cable end treatment are shown in Fig 1. 2. Termination is described below. (1) Strip cable outer jacket as indicated. (2) Slit outer jacket on both sides per Fig.1. (3) Fold back outer cover. (4) Remove insulator from cable. 1. Cable end treatment Fig.1 Male pin Soldering Should fix flush Contact fixing jig such as vise 1. Solder male pin to cable center conductor as indicated in Fig.2. (1) Pre-solder the solder pot of pin with Ø0.5mm string solder. (2) Male pin should fit flush against the cable insulator as shown. (3) Remove any excess solder from the pin with a knife.This surface must be smooth. (4) A properly soldered terminal will yield 500gf when stretched. 2. Soldering male pin to cable center conductor Fig.2 Clamp 15±0.2 Connector Remove excess insulator material (remaining after clamping is complated) with a knife or aimilarobject. 1. Insert the cable into the connector and make sure to push it all the way in. To confirm that the cable is fully inserted, make sure that the depth is 1.5 ± 0.2mm by measuring from the end of the connector to the tip of the male contact by using a vernier calipers or other suitable measuring device. 2. Use the HR10-TC-01 tool to crimp the metal fitting to the cable. 3. Crimping cable outer conductor Fig.3 HR10B-2.5CP(73) HR10B-2.5CJ(73) HR10 Series●High performance miniature circular connectors
HR10A-( )T Type (Threaded Coupling Type) HR10A-( )T connector is a new product having a threaded coupling locking mechanism. Electric parformance is same as HR10 and HR10A push-pull locking type connectors. Plug (Crimp type) Ø17 Ø9.5 M13∞0.75 Unit : mm Part No. HRS No. No. of Contacts HR10A-10TP-12PC(73) 110-0455-6 73 12 HR10A-10TP-12PC(73) (Representative example) (Representative example) Plug (Solder type) ØC B ØA D ØE HR10A-10TP-12P(73) Unit : mm Part No. HRS No. No. of Contacts ØA B ØC D ØE Remarks HR10A-7TP-6P(73) 110-0331-3 73 6 12 M10×0.75 7 35 5HR10A-7TP-6P(74) 110-0331-3 74 Gold plating HR10A-10TP-12P(73) 110-0432-0 73 17 M13×0.75 9.5 43 7HR10A-10TPA-12S(73) 110-0446-5 73 HR10A-10WTP-12P(73) 110-1101-9 73 15 M12×0.75 45.8 6.5 *HR10A-10WTP-12S(73) 110-1106-2 73 HR10A-13TPD-20P(73) 110-1015-9 73 20 20 M17×1 13 56.5 7 *Waterproof plug need resin fi lling inside when connector assembly. When mated, the connector against water penetration. HR10 Series●High performance miniature circular connectors
Unit : mm Part No. HRS No. No. of Contacts Ø A B C DEFG H HR10A-7TR-6SA(73) 110-0330-0 73 6 11 M10×0.75 M8×0.5 10 6.3 0.5 15.5 Ø0.55 HR10A-10TR-12SB(73) 110-0433-3 73 12 14 M13×0.75 M11×0.75 13 15.6 0.2×0.5 HR10A-10TR-12PB(73) 110-0457-1 73 15.5 HR10A-10TR-12PE(73) 110-0445-2 73 14 HR10A-10WTR-12SB(73) 110-1102-1 73 M12×0.75 M10.5×0.75 6.8 0 15.6 HR10A-13TR-20SB(73) 110-1014-6 73 20 18 M17×1 M14×0.75 17 9.3 17.8 Remarks : 1.For mounting holes, see page 15. However, 7TR size shell be referred to page 20 on the shell size 7. 2.For dip post arrangement, see page 16. Receptacle (Solder type) A F(HEX) C ØD B 5.7 E Unit : mm Part No. HRS No. No. of Contacts A B C ØD E F Remarks HR10-7TR-6S(73) 110-0089-0 73 6 M10×0.75 6.3 M8×0.5 11 14 10 Gold plating HR10A-10TR-12S(73) 110-0453-0 73 M13×0.75 M11×0.75 14 16 13 HR10A-10WTR-12S(73) 110-1104-7 73 M12×0.75 6.8 M10.5×0.75 Remarks : For mounting hole, see page 15(10TR,10WTR) 20(7TR). HR10A-10TR-12S(73) (Representative example) Receptacle (Crimp type) D E F(HEX) ØA B C Unit : mm Part No. HRS No. No. of Contacts ØA B C D E F HR10A-10TR-12SC(73) 110-0456-9 73 12 14 12 6.3 M13×0.75 M11×0.75 13 HR10A-13TR-20SC(73) 110-1002-7 73 20 18 15 9.3 M17×1 M14×0.75 17 Remarks : For mounting hole, see page 15 HR10A-10TR-12SC(73) (Representative example) Receptacle (Dip type) C D(HEX) B Dip post H ØA E 5.7 F G HR10A-10TR-12PB(73) (Representative example) HR10 Series●High performance miniature circular connectors
Jack (Solder type) Unit : mm Part No. HRS No. No. of Contacts ØA B ØC D Remarks HR10A-10TJ-12S(73) 110-0436-1 73 14.7 41.3 7 M13×0.75 HR10A-10TJ-12P(73) 110-0459-7 73 HR10A-10WTJ-12S(73) 110-1103-4 73 14 46.5 6.5 M12×0.75 * *Waterproof jack need resin fi lling inside when connector assembly. When mated, the connector against water penetration. D ØA B ØC (Representative example) HR10A-10TJ-12S(73) Panel mounting hole dimensions (Screw coupling) The mounting hole dimensions shown below are for connectors to be tightened by a hexagonal nut from the back of the panel. The dimensions below apply only to the HR10A-( )T and not the 7TR. For the dimensions of connectors of other types, see page 20. 9.6 +0.1 Ø11.1 +0.10 Ø10.6+0.1 Ø14.1 +0.10 Type HR10A-10TR (Panel thickness 1 to 2mm) Type HR10A-10TR (Panel thickness 1 to 2mm) 9.6 +0.1 Type HR10A-10WTR (Panel thickness 1 to 2mm) 8.6 +0.1 1.6 +0.1 Type HR10A-13TR (Panel thickness 1 to 1.5mm) HR10 Series●High performance miniature circular connectors
A A 1.15 1.2 A A 1.15 1.2 Receptacle dip post arrangement dimensions Contact Unit : mm Type Part No. HRS No. Type of plating Applicable cable Loose contact HR10-PC-111 110-0515 6 Partial gold plating 26 to 30 AWG HR10-PC-112 110-0513 0 Silver plating Reel contact HR10-PC-211 110-0516 9 Partial gold plating HR10-PC-212 110-0514 3 Silver plating Remarks : 1. Use cables with a coating outside diameter of 1mm or less. 2. Loose piece terminal are available in packs. Each pack contains 100 terminals. Strip terminals are available in reels. Each reel contains 10,000 terminals. Unit : mm Type Part No. HRS No. Type of plating Applicable cable Loose contact HR12-SC-111 112-0410 0 Partial gold plating 26 to 30 AWG HR12-SC-112 112-0411 3 Silver plating Reel contact HR12-SC-211 112-0407 6 Partial gold plating HR12-SC-212 112-0408 9 Silver plating Remarks : 1. Use cables with a coating outside diameter of 1mm or less. 2. Loose piece terminal are available in packs. Each pack contains 100 terminals. Strip terminals are available in reels. Each reel contains 10,000 terminals. Remarks : 1. The above fi gures are views from the mating side and pin inserts from the wiring-connection side. 2. Dimensional tolerance of ±0.05 is recommended for the board arrangement. 1.131.13 1.561.561.13 7-size 4 cores 7-size 6 cores 10-size 10 cores 10-size 12 cores 13-size 20 cores 1.13 0.9 0.9 1.8 1.8 (4 Places) (6 Places) (10 Places) (12 Places) (20 Places) 4 1 1.8 1.8 1.8 1.8 7-size 5 cores (5 Places) 2.5 2.58 2.38 2.38 0.950.95 2.75 2.11 0.55 0.48 2.85 2.85 0.95 0.95 1.1 1.38 2.5 2.55 2.55 1 1 1.77 1.77 0.8 2.4 0.8 2.4 2.71 2.71 1 1 1 2910 5 4 5 6789 1 0 161514131211 17 18 19 20 456 7 12 11 Ø0.8ʴ0.1 Ø0.8ʴ0.1 Ø0.8ʴ0.1 Ø0.8ʴ0.1 Ø0.8ʴ0.1 Ø0.8ʴ0.1 HR10 Series●High performance miniature circular connectors
Type Item Part No. HRS No. Applicable terminal Applicable cable Manual Manual crimping tool HT802/HR12-SC-1 150-0400-3 HR10-PC-112 26 to 30AWG HR12-SC-112 Automatic Automatic crimping Applicator AP105-HR12-1 901-2015-9 HR10-PC-211 212 26 to 30AWG HR12-SC-211 212 Cable crimping tool HR10-TC-01 150-0036-2 (HR10B-2.5CP(73), HR10B-2.5CJ(73)) HR10A-TC-02 150-0041-2 Ø5, Ø7 Extractor HR12-SC-TP 150-0050-3 HR12-SC-112 HR12-SC-212 RP6-SC-TP 150-0039-0 HR10-PC-112 HR10-PC-212 HR10B-TP 150-0061-0 HR10B-2.5CP(73) HR10B-2.5CJ(73) (HT802/HR12-SC-1) Hand Crimp Tool (HR10A-TC-02) Hand Cable Crimp Tool (HR10B-TP) Coaxial Contact Removal Tool (HR12-SC-TP) Auto Crimp Tool CM-105C (RP6-SC-TP) Extraction Tool HR10 Series●High performance miniature circular connectors
Part No. HRS No. Applicable connector HR10-7P-T01 150-0009-0 HR10-7P HR10-10P-T02 150-0010-9 HR10-10P HR10-7J-T03 150-0011-1 HR10-7J HR10-10J-T04 150-0012-4 HR10-10J HR10-13P-T05 150-0059-8 HR10-13P HR10-13J-T06 150-0060-7 HR10-13J Panel Plug CableReceptacle A Panel Plug CableReceptacle A Panel B Plug connection sleeve Cable Panel Plug connection sleeve B Cable Connecting tools When terminating the wires, use the jigs noted below for easy assembly / disassembly of the connector parts. 1.Inserting 2.Withdrawing HR10 TYPEHR10A TYPE Hold the plug at point A, align the plug guide with the receptacle guide, and push the plug straight. The plug will mate with the receptacle smoothly. Hold the plug connection sleeve B and pull the sleeve straight. The plug will come off easily. HR10 Series●High performance miniature circular connectors
Cable assembly procedure on plug side This applies also to the jack side assembly procedure. No special procedure is given here for the receptacle side because no special procedure is necessary. Table 2 spanner jaw distance Size HR10 HR10A 7 8 7.5 10 11 9.5 1 3 ____ 1 3 Table 1 Size Tightening force 7 1.5N·m(15kg·cm) 10 2N·m(20kg·cm)13 Table 3 cable end processing dimensions Size Dimension C for HR10 Dimension D for HR10A Solder type Crimp type 7 5.5 or less 10 15 to 2010 7 or less 16 1 3 ____ 2 5 HR10 TYPE HR10A TYPE 1 Use cables with a nominal sectional area of 0.129mm (26 AWG) at the fi nish outside diameters applicable for each size. After processing the cable ends according to the dimensions in the above drawings, fi t the parts to the cable as shown in the drawings. Fit the parts to the cable in the following order: tightener, clamp washer, and plug body. Fit the parts to the cable in the following order: cord bushing and plug body. (solder type) Insert the P shell unit into the assembly tool stand and solder it. (crimp type) After crimping the appropriate crimp terminal to the cable core, insert the crimp terminal into the terminal hole in the P shell unit. Assemble the connector in the following steps. 1. Screw the plug body into the thread in the P shell unit with the tightening force shown in Table 1 using a torque wrench with a fi xed torque. Before tightening the plug body,slacken part C so that no load is applied to the soldered wires. 2. Apply the clamp washer to the bifurcated part of the plug body, and then tighten the tightener until surface B touches the plug body surface A. Note : In order to prevent looseing, please apply an adhesive at the thread of plug body. 1. Fix by caulking the clamp accompanying the cable with the cable crimping tool(HR10A-TC-02) 2. Screw the plug body into the thread in the P shell until with a tightening force shown in Table 1 using a torque wrench with a fi xed torque. Before tightening the plug body, slacken the part D so that no load is applied to the soldered wires. 3. Tighten the set screw so that the tip of the screw presses one of the two bosses on the clamp. Fix the set screw with a tightening torque of 0.3N (3kg·cm). 4. Attach the cord bushing to the plug body. Note : In order to prevent looseing, please apply an adhesive at the thread of plug body. 5 This completes the work. For any question on using the plugs, contact our sales or engineering department. P shell unit Set screw Boss Clamp Plug body Spanner jaw distance Cord bushing Cable 2 or moreAbout 2 for solder type 2 for crimp type0 -0.5 P shell unit Plug body Bifurcated part Clamp washer Tightener Cable Face BFace A Spanner jaw distance About 2 C HR10 Series●High performance miniature circular connectors
Mounting hole dimension shown here is tight by hexagon nut from back side. Contact Arrangement A B ØC 7 size 10 size 13 size A 1.6 2.6 B 5.1 6.6 8.6 C 8.1 11.1 14.1 Panel thickness 0.7 to 2 0.8 to 1.5 Shell size Map mark +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 Shell size 7 size 10 size Contact arrangement No. of contacts 4 5 6 10 12 Withstanding voltage AC500V for a minute AC300V for a minute Current rating 2A Insulation resistance MIN 1,000Mø Contact resistance MAX 10mø Solder pot inside dia. Ø0.8 Shell size 10 size 13 size Contact arrangement No. of contacts 10+coaxial contact 20 Withstanding voltage AC300V for a minute Current rating 2A Insulation resistance MIN 1,000Mø Contact resistance MAX 30mø MAX 10mø Solder pot inside dia. ____ Ø0.8 Notes 1. The contact arrangement shown here is the mating surface of socket insert assembled. 2. The withstanding voltage shown here is test voltage value. 3. The isulation resistance value is measured at DC100V. 4. The contact resistance value is measured at DC1A. HR10 Series●High performance miniature circular connectors
2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN TEL: +81-45-620-3526 Fax: +81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 12/2017. Contents are subject to change without notice for the purpose of improvements. Precautions 1. Switch off the power of the circuit before disconnecting or plugging-in the connector. 2. Use a connector with socket contacts at the power side of the circuit. 3. Make sure that the coupling is in completely locked position. 4. Cable clamping, cable rotation, and other forces may vary with the cable construction. Please make sure that your cable is suitable for use with these connectors before usage and production. 5. This product series uses silver plated contacts. Silver reacts easily to exposure to sulfur gas so the below conditions may cause tarnishing. ɹɾDusty environments ɹɾArea with a high concentration area of gases such as sulfur dioxide gas, hydrogen sulfide gas, nitrogen dioxide gas and so on. Example; In close proximity to factory exhaust, automotive emissions, etc. ɹɾClose to heaters, or in other areas marked by extreme temperature differences or high humidity. ɹɾClose to rubber products includes rubber adhesives. The Electrical connection is not affected by tarnishing on a silver surface due to the wiping effect of the contact pins. Storage Packing state; Packed in original packing or equivalent container Temperature -10 to +60 ç Humidity 85% Max (It is recommended that the product be stored in an area of normal level of temperature and humidity, and free of any temperature fluctuation) Please use this products within 6 months of delivery. (After 6 month, please check the solderbility before use) “Storage” means long-term storage of the unused products in sealed packaging, prior to assembly to PCB. HR10 Series●High performance miniature circular connectors Powered by TCPDF (www.tcpdf.org)