HR10-7R-4SA | DigiCamel IC Datasheet

Online Datasheet

Read HR10-7R-4SA online.

HR10A-7P-4PA HIROSE | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 22

Technical content

Features

“A LITTLE GIANT” 5. HIGH DENSITY The most compact HR10 series is as slender as a The space-saving “push-pull” mechanism facilitates cigarette but it fits every application with well-balan- multi-installation of connectors. ced, simplified layout in limited space. 6. EASY WIRING AND MOUNTING 2. EASY “PUSH-PULL” OPERATION No use of screws makes wiring and mounting easier. One touch “push-pull” coupling mechanism assures 7. SIMPLE AND REFINED APPEARANCE easy and quick connecting and disconnecting. You Simple and well designed connectors with matte can couple it accurately just by pushing any part of finish enhance the appearance of the equipment. the connector housing. 3. POLARIZATION Five-key system permits only one way of coupling so that you can find right position to connect even when blind mating. 4, PROTECTION OF CONNECTION PIN A connector pin is located to avoid any damage which may be caused when blind mating.

Material & Finish : Main materials

Ordering Information

HR10A—7 P-4 PA (1) Model ‘ = (2) Shell size (3) Shell type (4) Number of contacts (5) Type of terminal ‘ : (6) Terminal form ° (1), Model: : Denotes HR10 series as follows: HR10A: Low-cost model HR10G: Shielded HR10E: Built-in capacitor HR10B: Coaxial terminal HR10D: Connector sleeve rotation inhibited (2) Shell size: Plug mating part outside diameter in mm. (3) Shell type: Indicates the type of shell as follows: F P: Plug R: Receptacle J: Jack (4) Number of contacts: Indicates the number of contacts. (5) Type of terminal: Indicates the type of terminal as follows: P: Male terminal S: Female terminal (6) Terminal form: Indicates terminal connection system in terminal form in alphabetic characters. C: Crimp connection system 64 |

Gold plating is the standard for the HR10 connector HR10 type terminals and silver plating is used for the terminals of other types of connectors. When using HR10 connectors combination with other types of connectors, be sure to check the plating specification. Plug . A Max HR10—7P—6P {An example in shape) < fem oe ET [| [1i0-0023=1 wnio= 7e= oF | 0 _[ass [7 [2 | oo | L [s10-o036=«| unio 7e— es] 6 [aes | | 7 [sa | ae | HR10—10P—12P Receptacle . A ! Sy =| = WT D HR10-7R—6S B(HEX) (An example in shape) 4 | 110-0031-o| wrio— 7A— 4s | 4 | 14 [11 [eas | mexos | 10 | 359 | [ito-o0so=2] wrno= ma= oP [4] w | 11 [oes [mos [10 | 250 | \\ [io=ooss=3 HRIO= 7A= 6s | S| 44 | [eas | wexos [To [aay | . [r10-00o4<8 [HAi0— 7A oP | 6] 44 [1 [eas | wos | 10 | 359 | 8 SS [0-o006—a | wetO=r0R—rae | 12 [ 46 14 [rn9 [we075| 13-9] HR10—10R—12S Remark: For mounting holes, see page 85.

Receptacle (PCB Dip Type) j G F b — 42) @) <: xy) | af W oy) * Dip post dia. 0.55 HR10—7R—6SA Cc D (HEX) (An example in shape) > [ wnsvo. | renno. [3a [oa Joe [© To Te [+ | s Jrem] mV [110-o0s0-9 |into- 7a- asa] 4 [11 |o.5 | menos | 10 [oa [os [155] 30 | : | [110-0060-4 |unvo- 7A- esa] 6 | 11 [aes | mex08 [10 [oa [os [iss] a0 | “| Friecoose-s Jnatomton—rasa 12 [14 [irs fwrnso75| v3 [6a [os [165] 50_| : [110—0085-8 |umto—1on—vePA| 12 | 14 [i198 [wirxors | a3 [oa [os [iss | oo | HR10—10R—12SA Remarit 2 For Dip post anangament re poe 20. : Jack . A Max ~ (1 TIA ad 7 Hr10-73-65 [ows [mame Pas] « [oe [oe [> [rol [10-0072 [wRio— 7s ass [a5 [1 eas [52 | 70 | [110-o028-s |Hrt0— 7s ae | 4 [285/11 [885 [52 | 70 | [110-o029-a |HR10— 7s es | 6 |2e5 | 11 [a5 [52 | 70 | [110-0000-7 |HRTO— WF | 6 [285 | 11 [e858 |62 | 70 | [11000076 |HRvo—Tou—vas [vans [4 [11.9] 72 | 140 | [110-o08-9 [nto—toi—vae | 12 [eas |r [ia [72 | 19 |

HR10A-10G T The model HR10A is a lowcost connector maintaining ype the excellent characteristics of the HR10 connector while meeting VA requirements. To ensure increased cable- clamping force, the cables are crimped with a special crimping tool, and to increase cable resistance to bending, the shell is covered with a rubber bushing. The model HR10G is a shielding connector having a built-in contact mechanism with the plug shell inside the receptacle. : The standard HR10A and HR10G connector contacts are silver-plated. Plug (Solder Type) A ae @ a af Lee at a * (An example in shape) HR10A-7P-6P Tor [_wrsne [tonne [Sas'[ « [oe [ve Too [ove] ‘ |110-o301-2 | wRioa—7e— 4p | 4 35 [ats| 7 6 | 90 | [r0-os1e-6 [wRIOA- 7P— oP [5 [os [ts] 7 [6 | 90 | i i [1109-08040 [HRTOAT 7e- os | 6 [35 [tis | 7 [6 |" 0 | [10-oaor=7 | WRtoa—soP—tae |" 12 43 [147 [os [7 | 160 | |*10-o402~0 | WRIOA—voP—i2s | i2_[aa_fia7 [os [7 | 16s | HR10A-10P-12P [170-0713-0 | HRIOA—raP—aor | 20 [saa [ re [13 | 7 | 370 | Plug (Crimp Type) : A His a oO) ieseellleal a f f23E=|==| HR10A-7P-6PC (An example in shape) [wes [rene FET « [om [oe [= fron] [t10-o501—1 [HRToA— 7P— arc | 4 [os [rs| 7 [Ss | os | |110-0502—4 [HRIOAS 7e— asc [4 [as [ris [ 7 |e |e | “Seg |110-0603—1 |HRIOA—top—rzrc [12 [4s_|ra7 [95 | 7 | 160 | [170-o804—8 |HRIGAioP—iasc [72 | 43 [147 [os | 7 | 165 | HR10A-10P-12PC [110-o701-0 |HRIOA—1aP—20°c | 20 |ées| 113 | 7 | 70 | [1109-07023 JHRIOA—19P—20s6 | 20 [sae] 19 13] 7 | 370 |

Receptacle (Solder Type) , A 6.3 5.7, ae 7 i HH t i [a ¢ . alo Wt Ss y so] e WA a 7: D HR10A—7R—6S HR10G—10R—12S E (HEX) (An example in shape) [_wrsvo | _recvo [Mia'[s [oe Too [0 Te Joos] [omens [Treen [iT Too [oo [0 [© [wean [nonas] [o-as0s-5 fumvon—ra—as [4 [va [ii [eas [woos [v0 [ae | [rrocteorms wmioocmaae | « [ie |v [oos| wows [| aw | rroasee-s [unton—rmar [4 [v4 [11 [eas [woos [10 | a0 | [rrocrom—e[nmoccrncae [a | 14 | v1 [ees [woos [10 | a5 | o-cxao-7 [wnron—rn-es [6 [v4 [11 faas | wexos [v0 | a0 | |rtomtens—2 | wmroa—m-es_ [6 [14 [14 [as | wonos [10 | 20 | [te-oszi-o| navonrn=se [S| v4 [1 [wes [woos | to [ay] [rionteoncs [aniocmrn-ae [6 [v4 | 11 [eas | wos | 10 | a9 | sis [10=coor-o funtos=re-os |e | [11 [a5 | woxos [ro [ao | [rvocvearce|wmroa—ron—ros [vo [ie [va [vio furmnoae| vo |e] [10-oo08=1 [unonm7a-or [6 [4 [11 fess [waxos [io | ae | [rromtene-o|nmvaomron—ror [10 [v6 | 1 [v9 |wrnn76| 19 | ee | [20-0408 | ron—ron—ros | 10 [16 | v4 [115 lwanco75| 19 | so] [rro-nene-a [rmramron—ras | 1a [ve [14 [v10|wrna7e| v9 | eo | |rie-oe10-8 | wmoa—ton—ior [10 [v6 | v4 [119 fwivso76| 19 [ey | [ro-te10-2 [Hmroe—ron—rar [12 [ve [v4 [ris [winors| 18 | 50 [1000-5 [raton-ton—rar [12 [ve | v4 [rn9,Jurnso76| 13 | 69 | [0-orv4-2 | wrvon-ran-aos | 20 _[vea | v8 [re fwvenze| v7 | ee | [:o-oris- [Haron—ran—sor | 20 [aoa [ve [15a [wiawore| 17 | 60] Receptacle (Crimp Type) . F : ‘E Gf. > re Za / y <|m {((, id * i ail Uy iS c HR10A—7R—6SC HR10G—10R—12SC D(HEX {An example in shape) A [0-050s=2|inioa—ra—aro [4 [11 Jans [axos [0 [eo [rea [ay | [ra-rms|anioG—rm—arc | « | [ees | wexos [10 [ea [22] a | [170-c506-owmron—rn=esc [6 [1 Joos [moos [30 [oa | w [oy | [rocrros-7|uniosmm-osc | 6 [v1 Jess |waxos [vo [ea | v2 | oy | [19-0070 anvon-rR-ore |e [vi [aes | waos [v0 [oa [yaa] a | [110-170s-o|mvea—mn-we | @ |v [eae | wos | wo [ea [vza| os | Sues [74 [rv9 furnsors[ va [oa | m [te | [rocrrer-a[nAroe-ron—rose| ro_[ve [vio fwinae| @ [ea | a | o | [4 [ira juniors [ve [es faa 6 | Jusno7s | 19 [63 [iaa| 6 | [119=0608-5 JHnton—ion—v2sc| 12 | v4 [119 furis076 | 9 6a | w |e | [ro-r705-e|wnroscron-rase| we [v4 [ria fwino7s| va [ea | 2 | os | [19-0007 [wnvoA—ton-sare| va_[ 14 [ova fwnno7e [va [ea [aa] e» | |110.17%0=7|wmvoa—ron-are| va _[ va [ria ninore [va [ea [vez | ee | [1#0-o700-6 fHRron—roR-2086[ 20 | 18 [164 [wrevo7s | 17 [a [= [a | [Hoct7ri—o|wmr0s-ton-20s| 20 [ve [rea fneo7s| 1 [ea | 8 | a | [1o-a7ot-s JHRion—soRzoro| 20_[18 ]164 |wvenoze| v7 [aa [vs [eo | [tom 2|ynvos—ron-aore| 20 [ve [rea fwiwors| 7 [ea [is [a]

Receptacle (Dip Type) . G F Lay A fi AR <| (he (af) faiN\\ | a ~ Ss 0.2X0.5 Cc HR10A—7R—6SB_ HR10G—10R—12SB D(HEX) (An example in shape) [ene [rove PT [oT © Te Te] | pone] | o-caia-a [Anroa—7A—as6_ | 4 [11 [eas] wows | wea [os [ee] | [110—0518—7 [ wRtoa—7A—a4eB [4 [11 [eas | Mews [10 }ea [os [66 | oo | |10-08a-2 | HRIOA—7R—ss8 [8 _[ 11_|eas | -Maos [10 [63 os [166 | a0] |#10-0a16-0 | WRI0A—7R-es8 [6 [11 Jeas | Mex05 [10 [63 [os lise] 35] [#1908172 | WRIoa—7n-ees_—[ 6 | 11_[eas [Mews [10 [ea los [166] 30] [M0=oa19-6 | HRIOA-toR—1088 [To [14 [118 [wiixo.78 | 13 [es [os [166 | Bo | ‘ [1ie-oata—s [ HRIOA-IOR—T0rB [1014 [1a | miin0.7 | 13 [63 [08 16H] Bo _| | o-oare=1 | HRIOA—TOR—T2s6_| 12 ia [118 [minors | 19 [69 os tres] Sa] | o—os6—4 | HRIOA—tOR—Tae8 [12 [14 [49 [Mino.76 | 13 [63 tos [188] 6a] [tio=o70r—7 | HRIOA-TaR—20s8 [20 [Te [154 [Mia07s | 17 fos | 0 [178] Bs | [110-0708-0 | HRIOA—1aR—zoPe [20 [18 [16.4 [Miao78 | 17 [93 | 0 178] 80 | [t0-1801~0 | WRI0G—7A—as8_ [4 [11 [eas | Méxo5 | 10 [63 [08 [158] a5] » [Hio=ta02—s | HRi0G—7A—are [441 [a5 | wexos | 10 [63 [os [wet a5] | 0—1605—1 [ HRIOG—rR—es5_ [6 | a1_feas | Moos | 10 fea fos [166] 30] [to=ta06-a | HRI0G—7R—ers “|G | 11 |aa6 | wex0.5 [10 }63 05 [156] oo [110-Teo7=7 | HRIOG—1OR—Toss [10 [14 [11.8 | minso7S [13 [63 [05 [156] 50] snieis | 10—te09—2 | HRIOG—toR—ras8 [12 [14 [14.9 [ Minwo76 [13 [69 Tos [18] Ba] [1o—te10—1 | HRIOG—rOR—1aPe | 2 | v4 [Ha | Mito. [73 [es |os [6] Sa] © [io=1i I= | HRI0G—1aR—2085 [90 [18 [184 [wro.7s | 7 [8a | 0 7a] ay] [to=iei2-7 | HRI0G—raR—20re [20 [ve [15.4 | Miawo.75 | 17 [es | 6 [178] 80 | Remarks: 1. For mounting holes, see page 85. 2. For dip post arrangement, see page 80. Dust Cap ° aN eP SW lus) CO 4 ie x GA HR10—7R—C (An example in shape) ["HasNo. Trento. Toa] 8] clo [ee] [t0-t0s8—s [imIO—A-S Pi [7 | s nz} | [110-0082-0 JHRVO-ioR-C_| 14 [as [ios | 14 | 15 |

Jack (Solder Type) ; A *15.5 py < ml oO a “hy s 8 af SS HR10A-7J-6S, {An example in shape) [vam | on [a] = [oe [oe [om ron] [ito-osce—4 | wRton—re—as | 4 [953 [a1 [eas | 6 | os | [to-oat0-3 | wRion—7i—ae | 4 [35.311 [eas | 5 [os | . [ro-osti—6 [HRIoA—7J—es | 6 [36a [71 [eas [5 | 9 | a | 110-012-9 [HRIoA-7i-6e [6 |s53 | 11 [eas | 5 | os | : [sio-oar1—0 [HRIOA-t0i—105 [To 43 [74 [t19 | 7 | 6a | q [ rio-oa12—s [HAIOA—ro—10r [to [as | 74 [ie | 7 | Tes | | iio-o1os—2 | HAToA-10i—128 [iz | a [v4 [ie | 7 | 165 | . [iio-o105-0 | HavOA—ror—raP [ve fas [a [ine | 7 [168 | HR10A-10J-12S, Jack (Crimp Type) A ‘ D aan (FX mQ)O a SA HR10A-7J-6SC (An example in shape) [_vrswe, [ renno. [in| « [oe [oo [0 [oe [wens] Se | 1i0-0512-8 |HATOAN7i-6sc_ [6 [355 | 1 eas [5 [S| oe | | r10-0610—7 [HRIoA-iai-r0se | 10 [aa [va [113 [ss | 7_| too | [ ti0-0613-2 [HRToA—i0/—ra8c | 12 [4a [4 [119 [55 [7 160 | [ tio-o705—1_|HRIOA—ta/—20s¢ | 20 [ses | 8 [64 [o5 | 7 | 370 | [iio-o706-4 [Hrtoa—13s—20ec | 20 [e858 | 18 [164 [85 | 7 | 370 |

Cable Connecting Methods ‘ HR10B-2.5CP Connecting Methods HR10B-2.5CJ 9 PROCESS 1. Cable end treatment PROCESS 3. Crimping cable outer conductor Fig. 1 ntos 8 Fig. 3 ges = = = DD =. aCe an: SP eS Clamp metal ‘Connector Slit cable outer jacket Remove excess insulator 2 pieces (180° reverse side) material (remaining after clamping is completed) (1) DIMENSIONS FOR CABLE END TREATMENT with a knife or similar ARE SHOWN IN FIG. 1. object. (2) TERMINATION IS DESCRIBED BELOW. . 1. Strip cable outer jacket as indicated. (1) Insert cable prepared per PROCESS 2 into the con- + 2. Slit outer jacket on both sides per Fig. 1. nector. The cable should be inserted until it comes 3. Fold back outer cover. ,; to a full stop. This may be verified by checking the 4. Remove insulator from cable. dimension from the side of the connector to the top of the male contact (as indicated in Fig.'3). This dimension should be 1.5mm#0.2. ; (2) Crimp this installed metal clamp with tool HR10- PROCESS 2. Soldering male pin to cable TC-01 per Fig. 3 and remove excess insulation center conductor with a knife. . Malu pin Fig. 2 Soldering Yo Should fit flush Contact fixing jig such as vise (1) SOLDER MALE PIN TO CABLE CENTER CON- DUCTOR AS INDICATED IN FIG. 2. 1, Pre-solder the solder pot of male pin with 0.5mm string solder. 2. Male pin should fit flush against the cable in- sulator as shown. 3. Remove any excess solder from the male pin | with a knife. This surface must be smooth. | 4. A properly soldered terminal will yield 500gf | when stretched.

The HR10D connector incorporates a guide key and slot Be careful that HR10D connector is not compatible with to prevent rotation of the coupling sleeve. A visual mark HR10, HR10A and HR10G. is used on the sleeve to aid in coupling operations. Plug Mating guide position mark, HR10D-13P-20PC * Hood 14.9 i feel =~ [oo ¢ ‘ a. ea (An example in shape) HATO 18188) ec Receptacle (Crimp Type) Mating guide position mark an i I M14 0.75 HR10D-13R-20SC Remark: For the mounting holes, see page 85

Receptacle (Dip Type) M14X0.75 {| } SS Dip post dia. ‘dl q Mating guide position mark 8 DeKo ak, [15.5 2.6 Remarks. 1. For mounting holes. See page 85. 2. For dip post arrangement see page 80.

HRIOA-[ 11 TYPE (Threaded Coupling Type) ee Scope HR10A—( )T connector is a new product having a mance is same as HR10 and HR10A push-pull locking type threaded coupling locking mechanism. Electric perfor- connector. Plug (Solder Type) D (“ell ral - ) * HR10A—10TP—12P (An example in shape) ee ; Liecsai-s-ai[wmocricerar | 3 fener} 7 teeters | [ 110-042-0| HATOAToOTR ar [v2 [7 [wis fos [ast 7 | | Fees —femscirae t-te twas fealee] [si0-1106-2 | watoa-sowre—izs | 12_[15 | wia075 | 95 [ase [6s |_| [Ho=ois-3 | HaroA—sareo=20r [20 [20 [wit | 13 [ees t 7 |_| Plug (Crimp Type) MG OT ENE HR10A—10TP—12PC [orev [ree PS [11o-o486-6 [Hnioa—ioTe ize | 12 |

Receptacle (Solder Type) : E i © +4 1 A F(HEX) HR10A—10TR-12S {An example in shape) [sm [oem [ee] » fe] eo [w]e [? [omen | | s10-080-0 [Hato-7ra-es | _6 | mioxo.75 [6.3 | mexos | 11 | 14 | 10 | Gotd plated] ‘0046530 | HAtOA-r0TA—12s_| 12 _[wiswo76 [os |wino7s [ta [iw lis | | Tio=t104—7 | HRIoA—r0WTRR128 | 12_[wrao7s [oa [wioso7s | vs [16 [v3 |_| Receptacle (Crimp Type) B SA HR10A—10TR—12SC D F(HEX) ° (An example in shape) [ wasn, [ reeno [Sistas fe] » | © Je] [io-oas6-a | nnioamiora—iaso | 12 [14 [2 [oa | wiao7s [minors | 19 | . [ro-1002-7 [wrron—rarr—2osc | 20 [ve [1s [os [wire | wtaxors [17 | Remark: For the mounting holes, see page 79. Receptacle (Dip Type) : G F @) ithe... ) . . WY CIM B c HR10A—10TR—12PB D(HEX) (An example in shape) ; [ wasne, [roe [Sacto] 6 | ce Totete fe] # [remas] | 0-0200-0 | Hnioa-7Ta—asa__| 6 | 11 |ioo7s [moos | 10 [ea]os| ws] os |_| [1i0-o4a5—s | umioa—roTR—1958_| 12 | 14 | wiso75 [winxo7s | 13 | 63] 05 |t5| 0x08 |_| [1008571 | waioa—toTa—128 [12 | 14 | wtsxo78 [wiixo7s | 13 [63 [os [15] 008 | | [ 1io-o8as—2 | HRtoA—roTR—rare [12 _[ ta | wnaxo.76 [wiimo7s [1a [es | os | 14 [omos |_| | 10-1102-1 | HRIoA—towTR—1288 | 12_| 14 [ wi2x0.75 | wio.sx0.75 | 13 [ea [o [155] 02x05 [| [rto-to1s-3 | wRt0A—tarR—20r8 [20 | 1 | wi7xt | wrao7s [17 [es | 0 |18| om0s |_| [mo=1ore-6 [nmioa—rstR—20s8_| 20 | 1@ | wr7ar [unevo7s | 7 |93i0 [valozos | | Femarksi 1. For the mounting holes, soo page 75. However, TTR size Wal be refered to page BS on the al azo 7

Jack (Solder Type) ‘ B SS \\ REY y} * =, SU D HR10A-10TJ-12S (An example in shape) [one | anne PT [= [ee] 0 [ao] [io-oss6—1 | HRioa—rovinwas_| 2 [van |as| 7 [waar | | [r10-0460-7 [ HRIOA—rOTI—12° | 12 [rar fara} 7 [wnoxo7s | [i10~1108—4 [ HntoA—rowTs—195 | 12 | 14 [a85 [65 [wraxo7s |_| Panel mounting hole dimensions(screw coupling) The mounting hole dimensions shown below are for con- nectors to be tightened by a hexagonal nut from the back of the panel. The dimensions below apply only to the HR10A—[ ]T and not the 7TR. For the dimensions of 1.63 connectors of other types, see page 85. (| 3) 10.673" 3 (2 Type HRIOA-10TR Type HR10A—10WTR Type HR10A~13TR (Panel thickness 1 to 2mm) (Panel 1 thickness 1 to 2mm) (Panel thickness 1 to 1.6mm)

Contact : Male Pin A 12 Portia = bai +

5 Peta 7

RRemarksi 1, Us eables witha coating outidedlarveer of Timm or ls, 2. Loose-piece terminal are available in packs. Each pack contains 100 terminals. Strip terminals are available in reels. Each reel con- tains 10,000 terminals. Female Pin ee [em oie are]

1.2 Partial me

R Partial ~.

1 La iV cmin | 12-0407=8 | HRI2—So-2 ANG26~#00

Remarks: 1. Use cables with a coating outside diameter of 1mm or lest, 2. Loosepiece terminal are available in pocks, Each pack conting : 100 terminals. Strip terminals are available in réels. Each reel con- Receptacle dip post arrangement dimensions 40.6 4 / places) i 60.6 ia AF: “ /e|> (6 places) 40.6 + | | 2 0.6 (2 places) a - paw ) {20 places), 3g 2.98 40.6 ia! XQ bid AT] o.95/ TT [0.95 (20 places iis] [fas ool los | y al, peratd Ia y welt ZelYX\\ TIER - EL ah T-size 4 cores ; Ez ita Ee eees 7-size 6 cores - we +H ° 4 ptt , ws nes =| ae VE Bmtsais3)) a Ae ee ae VY ota NPS cca f} 1 CT 1 17 ipa 177 wal CIC] bs 2. 2.55 2.71 2.7 ay s"T"] ry wl Tle hel 10-size 10 cores 10-size 12 cores rae ae 13-size 20 cores 7-size 5 cores Remarks: 1. The above figures are views of receptacle-socket inserts from the mating side and plug-pin inserts from the wiring-connection side. 2. Dimensional tolerance of +0.05 is recommended for the board arrangement.

Manual | Manual crimping tool | 160-0052-9 HR12-SC-TC AWG # 26~ #30 HR12-SC-112 ‘Automatic erimpin ~0005- - 901-2015-9 AP105-HR12-1 HR10-PC-211 AWG # 26~ #30 i 212 Automatic 213 Applicator HR12-SC-211 212 213 150-0036-2 HR10-TC-01 rN Cable crimping too! [ cows | waesc-re | wie 80 he 150-0050-3 HR12-SC-TP 150-0039-0 RP6-SC-TP . 150-0061-0 HR10B-TP @O@,+ 6 an y : SS RS E ei] : (HR12-SC-TC) a) |) 4] Se ae. alg 66 Hand Crimp Tool = — é SS . (HR12-SC-TP) SH — Ome . a . ‘ S| (HR10A-TC-02) (RP6-SC-TP) Hand Cable Crimp Tool Extraction Tool Auto Crimp Tool CM—105 (HR10B-TP) Coaxial Contact Removal Tool

How to use a Connector . ie i) Panel Panel Receptacle Plug Cable ; Plug connection sleeve Cable w 5 1) im fe “ 2 ‘ ; HIS a a —— = ny) a mat B Panel Panel w Receptacle cable Plug connection sleeve = 5 | — Cable * Po Le A B Hold the plug at point A, align the plug guide with Hold the plug connection sleeve B and pull the the receptacle guide, and push the plug straight. sleeve straight. The plug will come off easily. The plug will mate with the receptacle smoothly. : . Wiring Tool > ae HR10-10P-T02 HR10-10J-TO4 [“HRSNe. | __ PartNo. | Appicabe connecter]

@ Connection work procedure(plug side) © This applies also to the jack side connection work. © No special connection work procedure is given here for the receptacle side because no special procedure is necessary. P shell unit Plug body Clamp washer ‘Tightener _Cable g Bifurcated part - | te tbe ° — Cs = (LES i = a About 2 Cc D Spanner jaw distance P shell unit ‘Spanner jaw distance Clamp Plug body Cord bushing Cable d eee | ea =z A| |zormore ESHl(EE . About 2 for solder type D Boss 25.5 for crimp type O | 7 Set screw ‘ Table 3 Cable end processing dimensions Table 2 Spanner jaw distance Dimension |__Dimension D for HRI0A, Tablet [Size [ HR10 [HR10A | for HR10 [Solder type [sze7 [e [78 | | sie? |" SSories [10 [6-20 || Size? | 7.5Nemm (15kG-em) | [ siero | a1 “| 95 | [sizet0 [7 ores [16 | 15 =20 | | Size 10 | 2Nem (20k) | Lszeis [= [13] [Seis [= ee 2N+m (20kg-cm) [| : HR10 Type HR10A Type [ 1. | Use cables with « nominal sectional area of 0.129 mm? (AWG#26) at the finish outside diameters applicable for each size. After processing the cable ends according to the dimensions in the above drawings, fit the parts to the cable as shown in the draw- ings. Fit the parts to the cable in the following order: tightener, | Fit the parts to the cable in the following order: Cord bushing, clamp washer, and plug body. and plug body. 3 | (Solder type) Insert the P shell unit into the assembly jig stand and solder it. (Solder type) After crimping the appropriate crimp terminal to the cable core, insert the crimp terminal into the terminal hole in the P shell unit. 4 | Assemble the connector in the following steps. @) Screw the plug body into the thread in the P shell unit | (2) Fix by caulking the clamp accompanying the cable with with the tightening force shown in Table 1 using a torque the cable crimping tool (HR10A-TC-02). wrench with a fixed torque. @ Screw the plug body into the thread in the P shell until Before tightening the plug body, slacken pert C so that with a tightening force shown in Table 1 using a torque no load is applied to the soldered wires. wrench with a fixed torque. @ Apply the clamp washer to the bifurcated part of the plug Before tightening the plug body, slacken the part D so body, and then tighten the tightener until surface B s0 that no load is applied to the soldered wires. touches the plug body surface A, © Tighten the set screw so that the tip of the screw presses ‘one of the two bosses on the clamp. Fix the set screw with a tightening torque of 0.3N (3kg-cm). @ Attach the cord bushing to the plug body. 5 | This completes the work. For any question on using the plugs, contact our sales or engineering department.

{| Connector Male Pin side Female Pin side QI a G lla | UT hy (HR10-HR104 Le TRY TT || | > pig - - HR10G type Receptacle) Noe (HR10 type plug) - HB} (HR10 Type Jack) Aw Fee \\Receptacte : t+ . (HR10B Type Plug) (HR10D Type Plug) (ah CT a | es (HR10A-[ 1T Type Receptacle) =| Vi me = I (HR10A-[ ]T Type Plug) _ "| (HR10A-[ ]T Type Jack) Notes 1: When using a plug with male terminal, be sure to use a receptacle or jack fitted with female terminal. 2: Standard finish of the terminal is gold plating for the HR10, and silver plating for the HR10A and HR10G. Be sure to use male and female connectors of the same plating.

Recommended Mounting Hole . Mounting hole dimension shown here is tight by hexagon nut from back side. - - A [A ee [aes oar | psf ses Peer [aot | “ [Fetwicime [07-2 | o7~2 [osm ie | Se Contact Arrangement a YS ‘ v Vv y Vv ¥ - ® ® oe m° °d ®@ @® Contact arrangement @o (a) ® oe © © | Noofping Pt a Withstanding voltage ACS5O0V for a minute AC300V for a minute AC300V for a minute [ Currentrating [ACC AC“‘*C*C~*Y MIN 1,000 Mo MIN 1,000 Ma [ Minto00me | MAX10ma [MAX T0ma | MAX 10 mo Solder pot inside dia. 908 [ shetsie tse —CidC“(‘CSNCOOO#C(;‘#édNSeweOO~CSY E® O@9@ Oo DOGGSS OC OR|@@ 10 + Coaxial contact P20 Withstanding voltage AC300V for a minute AC300V for a minute MIN 1,000 Mo. MIN 1,000 M2 MAX 10 ma [axioma Solder potinside dia, [OR Note 1. The contact arrangement shown here is the mating surface of socket insert assembled in a receptacle. 2. The withstanding voltage shown here is test voltage value. 3. The insulation resistance value is measured at DC100V. 4._The contact resistance value is measured at DC1A. :

Product Information

HR10-7R-4SA specifications and overview.

Summary

HR10 SERIES SHELL SIZE 7mm PUSH-PULL CONNECTORS

Description

HR10 SERIES SHELL SIZE 7mm PUSH-PULL CONNECTORS

Source title HR10-7R-4SA Datasheet(PDF) - Hirose Electric

Related Parts

More parts from the same family.

Browse manufacturer