HLMT-QX00

HLMA-QX00 BOARDCOM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

Features

 Subminiature flat top package Ideal for backlighting and light piping applications  Subminiature dome package Nondiffused dome for high brightness  Wide range of drive currents  Colors: – 590-nm Amber – 605-nm Orange – 615-nm Reddish-Orange – 622/626-nm Red –6 3 5 - n m R e d  Ideal for space-limited applications  Axial leads  Available with lead configurations for surface mount and through hole PC board mounting Technology These subminiature solid state lamps use one of the two newly developed aluminum indium gallium phosphide (AlInGaP) LED technologies. The HLMT-devices are especially effective in very bright ambient lighting conditions. The colors 590-nm amber, 605-nm orange, 615-nm reddish-orange, 622/626-nm red, and 635-nm red are available with viewing angles of 15° for the domed devices and 125° for the flat top devices. HLMA-Qx00, HLMA-Px00, HLMT-Px00, and HLMT-Qx00 Subminiature High Performance AlInGaP LED Lamps Sun Power Series HLMA-PF00, HLMA-PG00, HLMA-PH00, HLMA-PL00, HLMA-QF00, HLMA-QG00, HLMA-QH00, HLMA-QL00, HLMT-PG00, HLMT-PH00, HLMT-PL00, HLMT-QG00, HLMT-QH00, HLMT-QL00

HLMA-Qx00, HLMA-Px00, HLMT-Px00, and HLMT-Qx00 Data Sheet Subminiature High Performance AlInGaP LED Lamps Device Selection Guide Absolute Maximum Ratings at TA = 25°C Part Number λd (nm) Typ. IV (mcd) Package Description Viewing Angle 2θ½ Package Outline HLMA-QL00 590 500 Domed, Nondiffused, Untinted 15° B HLMT-QL00 590 1000 HLMA-QJ00 605 500 HLMA-QH00 615 500 HLMT-QH00 615 800 HLMA-QG00 626 500 HLMT-QG00 622 1000 HLMA-QF00 635 500 HLMA-PL00 590 75 Flat Top, Nondiffused, Untinted 125° A HLMT-PL00 590 150 HLMA-PJ00 605 75 HLMA-PH00 615 75 HLMT-PH00 615 120 HLMA-PG00 626 75 HLMT-PG00 622 150 HLMA-PF00 635 75 Parameter HLMA-xxxx HLMT-xxxx Units Peak Forward Current[a a. See Figure 7 and Figure 8 to establish pulsed operating conditions. 100 100 mA Average Forward Current (IPEAK = 100 mA)a, b b. Maximum I AVG at f = 1 kHz. 30 30 mA DC Forward Currentc, d, e c. Derate linearly as shown in Figure 6. d. Drive currents between 10 mA and 30 mA are recommended for best long term performance. e. Operation at currents below 5 mA is not reco mmended; contact your Broadcom sales representative. 50 50 mA Power Dissipation 120 130 mW Reverse Voltage (IR = 100 µA) 5 V Transient Forward Current (10 µs Pulse)f f. The transient peak current is the maximum non-recurring peak cu rrent these devices can withstand without damaging the LED die and wire bonds. Operation at currents above Absolute Maximum Peak Forward Current is not recommended. 500 mA Operating Temperature Range –40 to +100 °C Storage Temperature Range –55 to +100 °C LED Junction Temperature 110 °C Lead Soldering Temperature (1.6 mm (0.063 in.) from body) 260°C for 5 seconds SMT Reflow Soldering Temperature 260°C for 20 seconds

HLMA-Qx00, HLMA-Px00, HLMT-Px00, and HLMT-Qx00 Data Sheet Subminiature High Performance AlInGaP LED Lamps Part Numbering System HLM x1 - x2 x3 00- x4 x5 x6 x7 x8 Number Description Option Option Description X1 Technology A/T AlInGaP PF l a t T o p X3 Color Option L Amber 590 nm J Orange 605 nm H Reddish Orange 615 nm G Red 622/626 nm F Red 635 nm X4 Minimum lV Bin Options Refer to the l V Bin table. X5 Maximum lV Bin Options Refer to the l V Bin table. X6 Color Bin Selection 0 Full Color Bin Distribution B Color Bins 2 and 3 K Color Bins 2, 3, and 4 R Color Bins 2 and 4 W Color Bins 2, 4, 6, and 7 X Color Bins 4, 6, and 7 X 7, X8 00 Straight Leads, Bulk Packaging, Quantity of 500 parts 11 Gull Wing Bend, Tape and Reel – 7 in. Reel

12 Gull Wing Bend, Bulk

14 Gull Wing Bend, Tape and Reel – 13 in. Reel 21 Yoke Bend, Tape and Reel – 7 in. Reel

22 Yoke Bend, Bulk

24 Yoke Bend, Tape and Reel – 13 in. Reel 31 Z-Bend, Tape and Reel – 7 in. Reel

32 Z-Bend, Bulk

34 Z-Bend, Tape and Reel – 13 in. Reel

HLMA-Qx00, HLMA-Px00, HLMT-Px00, and HLMT-Qx00 Data Sheet Subminiature High Performance AlInGaP LED Lamps Package Dimensions A – Flat Top Lamps B – Domed Lamps, Diffused and Nondiffused Package Mounting Proper right angle mounting to a PC board to prevent protruding cathode tab from shorting to anode connection. 0.94 1.24 (0.037) (0.049) 2.92 (0.115) MAX. 0.76 0.89 (0.030) (0.035) R. 0.63 0.38 (0.025) (0.015) 2.03 (0.080) 1.78 (0.070) 0.79 (0.031) 0.53 (0.021) 0.18 0.23 (0.007) (0.009) 2.08 2.34 (0.082) (0.092) NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES). 2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD. 0.50 (0.020) REF. 0.46 0.56 (0.018) (0.022) 0.25 (0.010) MAX. NOTE 2 0.20 (0.008) MAX. CATHODE 1.65 1.91 (0.065) (0.075) DIA. ANODE 11.68 10.67 (0.460) (0.420) BOTH SIDES 2.21 1.96 (0.087) (0.077) CATHODE STRIPE 1.14 1.40 (0.045) (0.055) 0.63 0.38 (0.025) (0.015) 2.21 1.96 (0.087) (0.077) 0.18 0.23 (0.007) (0.009) 2.44 1.88 (0.096) (0.074) 2.08 2.34 (0.082) (0.092) CATHODE STRIPE 0.46 0.56 (0.018) (0.022) 1.40 1.65 (0.055) (0.065) 0.25 (0.010) MAX. NOTE 2 0.20 (0.008) MAX. 0.50 (0.020) REF. CATHODE 1.65 1.91 (0.065) (0.075) DIA. ANODE 11.68 10.67 (0.460) (0.420) BOTH SIDES 0.79 (0.031) MAX. NO. ANODE DOWN. YES. CATHODE DOWN. CATHODE TAB

HLMA-Qx00, HLMA-Px00, HLMT-Px00, and HLMT-Qx00 Data Sheet Subminiature High Performance AlInGaP LED Lamps Optical Characteristics at TA = 25°C Part Number Luminous Intensity IV (mcd) at 20 mAa a. The luminous intensity, I v, is measured at the mechanical axis of the lamp package. The actual peak of the spatial radiation pattern may not be aligned with this axis. Total Flux ɸV (min) at 20 mAb b. ɸv is the total luminous fl ux output as measured with an integrating sphere. Peak Wavelength λpeak (nm) Color, Dominate Wavelength λd c (nm) c. The dominant wavelength, λd, is derived from the CIE Chromaticity Diagram and represents the color of the device. Viewing Angle 2θ½ Degreesd d. θ½ is the off -axis angle where the luminous intensity is ½ the peak intensity. Luminous Efficacy ηV e (lm/w) e. Radiant intensity, I e, in watts/steradian, may be calculated from the equation Ie = Iv/ηv, where Iv is the luminous intensity in candelas and ηv is the luminous efficacy in lumens/watt. HLMA-QL00-S00xx 160 500 — 250 592 590 15 480 HLMA-QL00-TU0xx 250 — 800 250 592 590 15 480 HLMA-QL00-TUKxx 250 — 800 250 592 590 15 480 HLMA-QL00-TVBxx 250 — 1250 250 592 590 15 480 HLMA-QL00-TVKxx 250 — 1250 250 592 590 15 480 HLMA-QL00-UV0xx 400 — 1250 250 592 590 15 480 HLMA-QL00-UVRxx 400 — 1250 250 592 590 15 480 HLMA-QL00-UWBxx 400 — 2000 250 592 590 15 480 HLMT-QL00-T00xx 250 1000 — 800 592 590 15 480 HLMA-QJ00-S00xx 160 500 — 250 609 605 15 370 HLMA-QH00-S00xx 160 500 — 250 621 615 15 263 HLMA-QH00-T00xx 250 500 — 250 621 615 15 263 HLMA-QH00-UW0xx 400 — 2000 250 621 615 15 263 HLMT-QH00-T00xx 250 500 – 800 621 615 15 263 HLMT-QH00-WX0xx 1000 — 3200 800 621 615 15 263 HLMA-QG00-S00xx 160 500 — 250 635 626 15 150 HLMA-QG00-TV0xx 250 — 1250 250 635 626 15 150 HLMT-QG00-T00xx 250 1000 — 800 635 622 15 150 HLMA-QF00-S00xx 160 500 — 250 650 635 15 110 HLMA-PL00-N00xx 25 75 — 250 592 590 125 480 HLMA-PL00-PRRxx 40 — 200 250 592 590 125 480 HLMA-PL00-PRXxx 40 — 200 250 592 590 125 480 HLMA-PL00-QRXxx 63 — 200 250 592 590 125 480 HLMT-PL00-P0Wxx 40 150 — 800 592 590 125 480 HLMA-PJ00-N00xx 25 75 — 250 609 605 125 370 HLMA-PH00-N00xx 25 75 — 250 621 615 125 263 HLMT-PH00-P00xx 40 120 — 800 621 615 125 263 HLMA-PG00-N00xx 25 75 — 250 635 626 125 150 HLMT-PG00-P00xx 40 150 — 800 635 622 125 150 HLMA-PF00-N00xx 25 75 — 250 640 635 125 110

HLMA-Qx00, HLMA-Px00, HLMT-Px00, and HLMT-Qx00 Data Sheet Subminiature High Performance AlInGaP LED Lamps Mechanical Option Matrix NOTE: All categories are established for classification of products. Products may not be available in all categories. Contact your local Broadcom representative for further clarification and information. Mechanical Option Code Definition

00 Straight Leads, Bulk Packaging, Quantity of 500 Parts

11 Gull Wing Leads, 12 mm Tape on 7 in. Diameter Reel, 1500 Parts per Reel

12 Gull Wing Leads, Bulk Packaging, Quantity of 500 Parts

14 Gull Wing Leads, 12 mm Tape on 13 in. Diameter Reel, 6000 Parts per Reel 21 Yoke Leads, 12 mm Tape on 7 in. Diameter Reel, 1500 Parts per Reel

22 Yoke Leads, Bulk Packaging, Quantity of 500 Parts

24 Yoke Leads, 12 mm Tape on 13 in. Diameter Reel, 6000 Parts per Reel 31 Z-Bend Leads, 12 mm Tape on 7 in. Diameter Reel, 1500 Parts per Reel

32 Z-Bend Leads, Bulk Packaging, Quantity of 500 Parts

34 Z-Bend Leads, 12 mm Tape on 13 in. Diameter Reel, 6000 Parts per Reel

Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago, and the A logo are among the trademarks of Broadcom and/or its affiliates in the United States, certain other countries, and/or the EU. Copyright © 2011–2020 Broadcom. All Rights Reserved. Broadcom reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does not assume any liability arising out of the application or use of this information, nor the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others.