HLMA-PH00 HP | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

Features

  • Subminiature Flat Top Package Ideal for Backlighting and Light Piping Applications
  • Subminiature Dome Package Nondiffused Dome for High Brightness
  • Wide Range of Drive Currents
  • Colors: 590 nm Amber, 615 nm Reddish-Orange
  • Ideal for Space Limited

Applications

  • Axial Leads
  • Available with Lead Configurations for Surface Mount and Through Hole PC Board Mounting

Description

The HLMX-PXXX flat top lamps use an untinted, nondiffused, truncated lens to provide a wide radiation pattern that is necessary for use in backlighting applica- tions. The flat top lamps are also ideal for use as emitters in light pipe applications. Dome Packages The HLMX-QXXX dome lamps use an untinted, nondiffused lens to provide a high luminous intensity within a narrow radiation pattern. Lead Configurations All of these devices are made by encapsulating LED chips on axial lead frames to form molded epoxy subminiature lamp packages. A variety of package configuration options is available. These include special surface mount lead configurations, gull wing, yoke lead, or Z-bend. Right angle lead bends at 2.54 mm (0.100 inch) and 5.08 mm (0.200 inch) center spacing are available for through hole mounting. For more infor- mation refer to Standard SMT and Through Hole Lead Bend Options for Subminiature LED Lamps data sheet. Technology These subminiature solid state lamps utilize one of the two newly developed aluminum indium gallium phosphide (AlInGaP) LED technologies, either the absorbing substrate carrier technology (AS = HLMA-Devices) or the transparent substrate carrier technology (TS = HLMT- Devices). The TS HLMT-Devices are especially effective in very bright ambient lighting condi- tions. The colors 590 nm amber and 615 nm reddish-orange are available with viewing angles of 15° for the domed devices and 125° for the flat top devices. SunPower Series HLMA-PH00 HLMT-PH00 HLMA-PL00 HLMT-PL00 HLMA-QH00 HLMT-QH00 HLMA-QL00 HLMT-QL00 5964-9364E

Viewing Angle Amber Reddish-Orange Package Package Description 2 θ1/2 λd = 590 nm λd = 615 nm Outline Domed, Nondiffused 28 ° HLMA-QL00 HLMA-QH00 B Untinted HLMT-QL00 HLMT-QH00 Flat Top, Nondiffused, 125 ° HLMA-PL00 HLMA-PH00 A Untinted HLMT-PL00 HLMT-PH00 NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). 2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD. 0.25 (0.010) MAX. 0.20 (0.008) MAX. 0.50 (0.020) REF. CATHODE 1.65 1.91 (0.065) (0.075)DIA. ANODE 0.46 0.56 (0.018) (0.022) NOTE 2 11.68 10.67 (0.460) (0.420) BOTH SIDES Package Dimensions (A) Flat Top Lamps (B) Domed Lamps, Diffused and Nondiffused 0.46 0.56 (0.018) (0.022) 1.40 1.65 (0.055) (0.065) 0.25 (0.010) MAX. 0.20 (0.008) MAX. 0.50 (0.020) REF. CATHODE 1.65 1.91 (0.065) (0.075)DIA. ANODE 11.68 10.67 (0.460) (0.420) BOTH SIDES NOTE 2 1.14 1.40 (0.045) (0.055) 0.58 0.43 (0.023) (0.017) 1.91 2.16 (0.075) (0.085) 0.18 0.23 (0.007) (0.009) 0.76 (0.030) MAX. 1.91 2.41 (0.075) (0.095)2.08 2.34 (0.082) (0.092) CATHODE STRIPE 0.94 1.24 (0.037) (0.049) 2.08 2.34 (0.082) (0.092) CATHODE STRIPE 2.92 (0.115) MAX. 0.76 0.89 (0.030) (0.035) 0.63 0.38 (0.025) (0.015) 0.18 0.23 (0.007) (0.009) 1.91 2.16 (0.075) (0.085) 2.03 (0.080) 1.78 (0.070) 0.79 (0.031) 0.53 (0.021)

Absolute Maximum Ratings at TA = 25°C HLMA-QL00/QH00/PL00/PH00 HLMT-QL00/QH00/PL00/PH00 All Devices Lead Soldering Temperature SMT Reflow Soldering Temperatures Notes: 1. Maximum IAVG at f = 1 kHz. 2. Refer to Figure 6 to establish pulsed operating conditions. 3. Derate linearly as shown in Figure 4. 4. The transient peak current is the maximum non-recurring peak current these devices can withstand without damaging the LED die and wire bonds. Operation at currents above Absolute Maximum Peak Forward Current is not recommended. 5. Drive currents between 5 mA and 30 mA are recommended for best long term performance. 6. Operation at currents below 5 mA is not recommended, please contact your Hewlett- Packard sales representative.

  1. The luminous intensity, Iv, is measured at the mechanical axis of the lamp package. The actual peak of the spatial radiation pattern

may not be aligned with this axis.

  1. φv is the total luminous flux output as measured with an integrating sphere.
  2. The dominant wavelength, λd, is derived from the CIE Chromaticity Diagram and represents the color of the device.
  3. θ1/2 is the off-axis angle where the liminous intensity is 1/2 the peak intensity.
  4. Radiant intensity, Iv, in watts/steradian, may be calculated from the equation Iv = Iv/ηv, where Iv is the luminous intensity in candelas

and ηv is the luminous efficacy in lumens/watt. NO. ANODE DOWN. YES. CATHODE DOWN. Figure 1. Proper Right Angle Mounting to a PC Board to Prevent Protruding Cathode Tab from Shorting to Anode

Figure 1. Relative Intensity vs. Wavelength. All Devices.