HLMA-DX05 HP | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

Features

  • High Light Output Over a Wide Range of Currents
  • Popular T-1 and T-1 3/4 Packages
  • Choice of Three Colors Amber Reddish-Orange Deep Red
  • Wide Viewing Angles
  • Long Life: Solid State Technology
  • Available on Tape and Reel

Applications

  • Outdoor Message Boards
  • Automotive Lighting
  • Portable Equipment
  • Medical Equipment
  • Changeable Message Signs

Description

The HLMA-D/KXXX series tinted, diffused, solid state lamps utilize the newly developed aluminum indium gallium phosphide (AlInGaP) LED technology. This technology has a very high luminous efficiency, capable of producing high light output over a wide range of drive currents. These LED lamps are available with a choice of two colors, 592 nm amber and 615 nm reddish- orange, and with two viewing angles, 65° and 60°. The HLMP-D/JXXX series tinted, diffused solid state lamps utilize the highly optimized transparent substrate aluminum gallium arsenide (TS AlGaAs) LED technology. This technology has a very high luminous efficiency, Device Selection Guide Viewing Reddish- Deep Angle Amber Orange Red Package Package Description 2 θ1/2 λd = 592 nm λd = 615 nm λd = 644 nm Outline T-13/4 (5 mm), Tinted, Diffused, 65 ° HLMA- HLMA- A Standard Current DL05 DH05 T-1 (3 mm), Tinted, Diffused, 60 ° HLMA- HLMA- B Standard Current KL05 KH05 T-13/4 (5 mm), Tinted, Diffused, 40 ° HLMP- A Standard Current D115 T-13/4 (5 mm), Tinted, Diffused, 25 ° HLMP- A Standard Current D120 T-1 (3 mm), Tinted, Diffused, 55 ° HLMP- C Standard Current J100 T-1 (3 mm), Tinted, Diffused, 55 ° HLMP- C Diffused, Low Current J150 5964-9287E

0.89 (0.035) 0.64 (0.025) 0.45 (0.018) SQUARE NOMIMAL 5.08 (0.200) 4.57 (0.180) 9.19 (0.362) 8.43 (0.332) 25.40 (1.00) MIN. 1.27( 0.050) NOM. CATHODE 6.10 (0.240) 5.59 (0.220) 2.54 (0.100) NOM. CATHODE NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). 2. AN EPOXY MENISCUS MAY EXTEND ABOUT 1 mm (0.040") DOWN THE LEADS. Package Dimensions 3.18 (0.125) 2.67 (0.105) 24.13 (0.95) MIN. 1.27 (0.050)NOM. 1.02 (0.040) 6.35 (0.250) 5.58 (0.220) 0.45 (0.018)SQUARE NOMINAL CATHODE 2.54 (0.100)NOM. NOM. 4.70 (0.185) 4.19 (0.165) 3.43 (0.135) 2.92 (0.115) ANODE 3.18 (0.125) 2.67 (0.105) 24.13 (0.95) MIN. 1.27 (0.050)NOM. 1.02 (0.040) 6.35 (0.250) 5.58 (0.220) 0.45 (0.018) SQUARE NOMINAL ANODE 2.54 (0.100)NOM. NOM. 4.70 (0.185) 4.19 (0.165) 3.43 (0.135) 2.92 (0.115) CATHODE A B C HLMA-DL05/DH05/Kl05/KH05 AlInGaP Lamps Absolute Maximum Ratings at TA = 25°C HLMA- HLMA- HLMA- HLMA- Parameter DL05 DH05 KL05 KH05 Units DC Forward Current[1,3,4] 50 50 50 50 mA Peak Forward Current[2] 200 200 200 200 mA Average Input Power[2] 103 103 103 103 mW Reverse Voltage (IR = 100 µA ) 55 55 V Operating Temperature Range -40 to -40 to -40 to -40 to °C +100 +100 +100 +100 Storage Temperature Range -55 to -55 to -55 to -55 to °C +100 +100 +100 +100 Junction Temperature 110 °C Soldering Temperature 260 °C for 5 second [1.59 mm (0.06 in.) below seating plane] Notes: 1. Derate linearly as shown in Figure 4. 2. Any pulsed operation cannot exceed the Absolute Max Peak Forward current as specified in Figure 5. 3. Drive currents between 10 mA and 30 mA are recommended for best long term performance. 4. Operation at currents below 10 mA is not recommended, please contact your Hewlett-Packard sales representative. capable of producing high light output over the wide range of drive currents from 500 µA to 50 mA. The color is deep red at a dominant wavelength of 644 nm. TS AlGaAs is a flip-chip LED technology, die attached to the anode lead and wire bonded to the cathode lead. Available view- ing angles are 25°, 40°, and 55°.

HLMP-D115/D120/J100/J150 TS AlGaAs Red Lamps Absolute Maximum Ratings at TA = 25°C HLMP- HLMP- HLMP- HLMP- Parameter D115 D120 J100 J150 Units DC Forward Current[1] 50 50 50 50 mA Peak Forward Current[2] 300 300 300 300 mA Average Input Power[2] 100 100 100 100 mW Reverse Voltage (IR = 100 µA ) 55 55 V Operating Temperature Range -55 to -55 to -55 to -55 to °C +100 +100 +100 +100 Storage Temperature Range -55 to -55 to -55 to -55 to °C +100 +100 +100 +100 Junction Temperature 110 °C Soldering Temperature 260 °C for 5 second [1.59 mm (0.06 in.) below seating plane] Notes: 1. Derate linearly as shown in Figure 12. 2. Any pulsed operation cannot exceed the Absolute Max Peak Forward current as specified in Figure 13. Optical Characteristics at TA = 25°C Luminous Color, Viewing Intensity Peak Dominant Angle Luminous IV (mcd) Wavelength Wavelength 2 θ1/2 Efficacy Part Number @ 20 mA [1] λpeak (nm) λd[2] (nm) Degrees [3] ηv D115 138 250 654 644 40 85 D120 138 350 654 644 25 85 J100 39 175 654 644 55 85 J150 1.3 3.0 654 644 55 85 Notes: 1. φv is the total luminous flux output as measured with an integrating sphere. 2. The dominant wavelength, λd, is derived from the CIE Chromaticity Diagram and represents the color of the device. 3. θ1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity. Electrical Characteristics at TA = 25°C Forward Reverse Capacitance Speed of Response Voltage Breakdown C (pF) τs (ns) Part V F (Volts) V R (Volts) V F = 0 Thermal Time Constant Number @ I F = 20 mA @ I R = 100 µA f = 1 mHz Resistance e -t/τs D115 1.85 2.4 5 20 20 260 45 D120 1.85 2.4 5 20 20 260 45 J100 1.85 2.4 5 20 20 290 45 J150 1.6 1.9 5 20 20 290 45