HLK-5D1205 AGELECTRONICA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 5

Technical content

http://www.agelectronica.com HLK-5D1205 CONVERTIDOR DC-DC ENTRADA (9V-18V) SALIDA 5V 1A 5W A variety of specifications for power module selection MULTIPLE SPECIFICATIONS AVAILABLE Same size, package and pin of same type power module MODEL POWER VOLTAGE ELECTRICITY HLK-5D1205 5W 5V 1000mA HLK-5D1212 5W 12V 417mA HLK-5D1215 5W 15V 83mA HLK-5D1224 5W 24V 210mA *Wide pressure 9~18V (2:1) input voltage regulator output *International standard pin:25.4X25.4X11mm product features PRODUCT FEATURES  Ultra-thin small size standard package and standard pins  Wide range input (2:1) voltage: 9~18VDC  Low power consumption, environmental protection, standby power consumption is only 0.3W (typical value)  Input and output isolation withstand voltage 1500VDC  Ultra-fast startup: 100ms (typical value)  High efficiency, conversion efficiency up to 78% (Typ)  Operating temperature range: -40°C~+85°C  Good output short circuit and over current protection and self-recovery  High reliability, long life design, continuous work over 100000H  Potting and sealing with high-quality environmentally friendly waterproof and thermal conductive glue, dustproof, moistureproof, shockproof and flame retardant  Meet UL/CE/EMC and safety testing requirements  Can be used in medical, industrial control, electric power, instrumentation, communication, railway and other fields

http://www.agelectronica.com Operating temperature environment and load characteristics WORKING ENVIRONMENT TEMPERATURE & LOAD CHARACTERISTICS Typical application circuit APPLICATION CIRCUIT Recommended test circuit Generally recommended capacitance: C1: 47-100μF; C2, C3: 10-22μF. All DC/DC converters of this series are tested according to the recommended test circuit shown in the figure below before leaving the factory. If it is required to further reduce the input and output ripple, the input and output external capacitors C1, C2, C3 can be increased or selected in series with capacitors with a small equivalent impedance, but the capacitance cannot be greater than the maximum capacitive load of the product.

http://www.agelectronica.com EMC solution-recommended circuit Recommended parameters: FUSE: Connect the corresponding fuse according to customer needs MOV varistor: 14D330K LDM1/common mode inductance: 10mH E1, E2 electrolytic capacitor: 100μF/50V C0, C1 ceramic capacitors: 1μF/50V LDM2 differential mode inductor: 10μH CY1 safety Y2 capacitor: 1nF/250Vac Output filter peripheral recommended circuit Note: 1. C2 and C3 use high frequency and low resistance electrolytic capacitors, and the total capacity should not exceed the maximum capacitive load marked in the manual, otherwise the module will not start normally. 2. For capacitive load, a minimum load of 3% must be guaranteed, otherwise it will cause abnormal output of the module.

http://www.agelectronica.com Recommended parameters: LDM3/LDM4 inductance: 1μH C2, C3 electrolytic capacitor: 220μF C4 ceramic capacitor: 1μF/50V Ripple & noise test: twisted pair method 20MHz bandwidth testing method: 1. Ripple noise is connected using 12# twisted pair, the oscilloscope bandwidth is set to 20MHz, 100M bandwidth probe, and 0.1uF polypropylene capacitor and 47uF high frequency low resistance electrolytic capacitor are connected in parallel to the probe end, and the oscilloscope sampling uses Sample sampling mode . 2. Connect the power input terminal to the input power supply, and the power output is connected to the electronic load through the fixture board. For testing, use a 30cm±2cm sampling line to sample directly from the power output port. The power line selects the corresponding wire diameter wire with insulation according to the output current. (As shown in FIG)

http://www.agelectronica.com Dimensions and weight DIMENSIONS & WEIGHT Pin description: 1: -Vin input negative; 2: +Vin input positive; 3: +Vo output positive; 4: NC; 5: -Vo output negative; 6: NC *Note: If the definition of each pin of the power module does not match the selection manual, the label on the physical label shall prevail. República del Salvador N° 20 Segundo Piso Teléfono: 55 5130 - 7210 ACOTACIÓN: N/A http://www.agelectronica.com ESCALA: N/A REALIZO: OGJ REV: JFRR TOLERANCIA: N/A CONVERTIDOR DC-DC ENTRADA (9V-18V) SALIDA 5V 1A 5W TOLERANCIA: N/A Fecha: 17/05/2022 No. Parte: HLK-5D1205