HDF802A1S4 SHOULDER | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 7
Technical content
www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 1 of 7 规格书编号 S PEC N O : 产 产 品 品 规 规 格 格 书 书 S S P P E E C C I I F F I I C C A A T T I I O O N N CUSTOMER 客 户 ： PRODUCT 产 品 ： SAW FILTER MODEL NO 型 号 ： HDF 802 A 1 SMD - 4 MARKING 印 字 ： HDF4 846 PREPARED 编 制 ： CHECKED 审 核 ： APPROVE D 批 准 ： D A T E 日 期 ： 200 9 - 6 - 8 无锡市好达电子有限公司 Shoulder Electronics Limited 客户确认 C USTOMER RECEIVED: 审核 C HECKED 批准 APPROVED 日期 D ATE
SAW FILTER HDF 802 A 1 SMD - 4 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 2 of 7 1. SCOPE This specification shall cover the characteristics of SAW filter With HDF 802 A 1 used for the page system. 2. ELECTRICAL SPECIFICATION DC V oltage VDC 10V AC V oltage Vpp 10V50Hz/60Hz Operation temperature - 4 0 ℃ to +85 ℃ Storage temperature - 45 ℃ to +85 ℃ Electronic Characteristics 2 - 1.Typical frequency response 2 - 2.Electrical characteristics U nit Minimum Typical Maximum Center Frequency MHz - 802 - Insertion Loss (In Fc +/ - 4 MHz) dB 2.5 3.0 Amplitude Ripple (In Fc +/ - 4 MHz) dB 0 .5 1.0 Relative Attenuation
0.3 MHz ~ Fo - 25 MHz
Fo+45 MHz ~ … . dB 4 0 4 0 Input/Output Impedance Ohms 50
SAW FILTER HDF 802 A 1 SMD - 4 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 3 of 7 3. TEST CIRCUIT 4. DIMENSION Marking ： HDF 4 846 HD: Brand F : Filter 4 : SMD - 4 846 : No.
SAW FILTER HDF 802 A 1 SMD - 4 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 4 of 7 5. ENVIRONMENTAL CHARACTERISTICS 5 - 1 High temperature exposure Subject the device to +85 ℃ for 16 hours. Then release the filter into the room conditions for 24 hours prior to the measurement. It sha ll fulfill the specifications in 2 - 2 . 5 - 2 Low temperature exposure Subject the device to - 4 0 ℃ for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2 - 2 . 5 - 3 Temper ature cycling Subject the device to a low temperature of - 40 ℃ for 30 minutes. Following by a high temperature of +8 5 ℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the me a surement. It shall meet the specifications in 2 - 2 . 5 - 4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260 ℃ ± 10 ℃ for 10 ± 1 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in 2 - 2 . 5 - 5 Solde rability Subject the device terminals into the solder bath at 245 ℃ ± 5 ℃ for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in 2 - 2 . 5 - 6 Mechanical shock Drop the device randomly onto the concrete f loor from the height of 1m 3 times. the device shall fulfill the specifications in 2 - 2 . 5 - 7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifi cations in 2 - 2 . 6. REMARK
6.1 Static voltage
Static voltage between signal load & ground may cause det e rioration &destruction of the component. Please avoid static voltage.
6.2 Ultrasonic cleaning
Ultrasonic vibration may cause det e ri ora tion & destruction of the component. Please avoid ultrasonic cleaning
6.3 Soldering
Only leads of component may be solded. Please avoid soldering another part of component.
SAW FILTER HDF 802 A 1 SMD - 4 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 5 of 7 7. Packing
7.1 Dimensions
(1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage.
7.2 Reeling Quantity
1000 pcs/reel 7’’ 3000 pcs/reel 13’’
7.3 Taping Structure
(1) The tape shall be wound around the reel in the direction shown below. (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications.
SAW FILTER HDF 802 A 1 SMD - 4 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 6 of 7 8. TAPE SPECIFICATIONS 8.1 Tensile Strength of Carrier Tape: 4.4N/mm width
8.2 Top Cover Tape Adhesion (See the below figure)
(1) pull off angle: 0~15 º (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions
SAW FILTER HDF 802 A 1 SMD - 4 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 7 of 7 [Unit:mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.00 ±0.30 5.50 ±0.10 1.75 ±0.10 4.00 ±0.10 8.00 ±0.10 2.00 ± 0.10 Ø1.50 Ø1.0 ± 0.25 0.25 ±0.05 1.65 ±0.10 4.04 ±0.10 4.10 ±0.10 [Figure 2] [Unit:mm] A B C D E W t r Ø 330 ± 1.0 Ø 100 ± 0.5 Ø 13 ± 0.5 Ø 21 ± 0.8 ± 0.5 ± 0.3 max. 1.0 max.