HDF455A1S4 SHOULDER | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 1 of 8 规格书编号 S PEC N O : 产 产 品 品 规 规 格 格 书 书 S S P P E E C C I I F F I I C C A A T T I I O O N N CUSTOMER 客 户 ： PRODUCT 产 品 ： SAW FILTER MODEL NO 型 号 ： HDF 4 5 5A1 SMD - 4 M ARKING 印 字 ： HDF44 97 PREPARED 编 制 ： CHECKED 审 核 ： APPROVED 批 准 ： D A T E 日 期 ： 20 1 0 - 12 - 2 1 无锡市好达电子 股份 有限公司 Shoulder Electronics Limited 客户确认 C USTOMER RECEIVED: 审核 C HECKED 批准 APPROVED 日期 D ATE
SAW FILTER HDF 4 5 5A1 S 4 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 2 of 8 更改历史记录 History Record 更改日期 Date 规格书编号 Spec . No . 产品型号 Part No . 客户产品型号 Customer No . 更改内容描述 Modify Content 备注 Remark
SAW FILTER HDF 4 5 5A1 S 4 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 3 of 8 1. SCOPE This specification shall cover the characteristics of SAW filter With F4 55 A 1 used for the page system. 2. ELECTRICAL SPECIFICATION DC V oltage VDC 10V AC V oltage Vpp 10V50Hz/60Hz Operation temperature - 4 0 ℃ to + 85 ℃ Storage temperature - 45 ℃ to +85 ℃ RF Power Dissipation 27 dBm Electronic Characteristics 2 - 1.Typical frequency response
SAW FILTER HDF 4 5 5A1 S 4 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 4 of 8 2 - 2.Electrical characteristics Part number F4 5 5A 1 Un it Nominal center frequency (Fo) 4 5 5 MHz Insertion Loss 406.6MHz ~ 416.6 MHz fo fo +39.8~ fo +45.8MHz 50min. 3 . 5 max 45 min dB Bandwidth （ - 3dB ） ± 5 ~ ± 7 MHz Ripple (with Fo ± 5 .0MHz) 2.0max dB Input/Output Impedance(Nominal) 50//0 Ω /pF 3. TEST CIRCUIT 4. DIMENSION
SAW FILTER HDF 4 5 5A1 S 4 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 5 of 8 5. ENVIRONMENTAL CHARACTERISTICS 5 - 1 High temperature exposure Subject the device to +85 ℃ for 16 hours. Then release the filter into the room conditions for 24 hours prior to the measurement. It shall fulfill the spec ifications in 2 - 2 . 5 - 2 Low temperature exposure Subject the device to - 4 0 ℃ for 16 hours. Then release the device into the room conditions for 24 hours prio r to the measurement. It shall fulfi ll the specifications in 2 - 2 . 5 - 3 Temperature cycling Subje ct the device to a low temperature of - 40 ℃ for 30 minutes. Following by a high temperature of +8 5 ℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the me a surement. It shall meet the specifications in 2 - 2 . 5 - 4 Resis tance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260 ℃ ± 10 ℃ for 10 ± 1 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in 2 - 2 . 5 - 5 Solderability Subject the device terminals into the solder bath at 245 ℃ ± 5 ℃ for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in 2 - 2 . 5 - 6 Mechanical shock Drop the device randomly onto the concrete floor from the he ight of 1m 3 times. the device shall fulfill the specifications in 2 - 2 . 5 - 7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in 2 - 2 . 6. REMARK
6.1 Static voltage
Static voltage between signal load & ground may cause det e rioration &destruction of the component. Please avoid static voltage.
6.2 Ultrasonic cleaning
Ultrasonic vibration may cause det e ri oration & destructio n of the component. Please avoid ultrasonic cleaning
6.3 Soldering
Only leads of component may be soldered. Please avoid soldering another part of component. 7. Packing
7.1 Dimensions
(1) Carrier Tape: Figure 1 (2) Reel: Figure 2
SAW FILTER HDF 4 5 5A1 S 4 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 6 of 8 (3) The pro duct shall be packed properly not to be damaged during transportation and storage.
7.2 Reeling Quantity
1000 pcs/reel 7’’ 3000 pcs/reel 13’’
7.3 Taping Structure
(1) The tape shall be wound around the reel in the direction shown below. (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. 8. TAPE SPECIFICATIONS
SAW FILTER HDF 4 5 5A1 S 4 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 7 of 8 8.1 Tensile Strength of Carrier Tape: 4.4N/mm width
8.2 Top Cover Tape Adhesion (See the below figure)
(1) pull off angle: 0~15 º (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions [Unit:mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.0 ± 0.3 5.5 ± 0.05 1.75 ± 0.1 4.0 ± 0.1 8.0 ± 0.1 2.0 ± 0.05 Ø 1.5 ± 0.1 Ø 1.0 ± 0.25 0.3 ± 0.05 2.10 ± 0.1 6.40 ± 0.1 5.20 ± 0.1 [Figure 2]
SAW FILTER HDF 4 5 5A1 S 4 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 8 of 8 [Unit:mm] A B C D E W t r Ø 330 ± 1.0 Ø 100 ± 0.5 Ø 13 ± 0.5 Ø 21 ± 0.8 ± 0.5 ± 0.3 max. 1.0 max.