HDF220AS3 SHOULDER | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 1 of 8 规格书编号 S PEC N O : 产 产 品 品 规 规 格 格 书 书 S S P P E E C C I I F F I I C C A A T T I I O O N N CUSTOMER 客 户 ： PRODUCT 产 品 ： SAW FILTER MODEL NO 型 号 ： HDF 2 20 A SMD - 3 M ARKING 印 字 ： HDF218 PREPARED 编 制 ： CHECKED 审 核 ： APPROVE D 批 准 ： D A T E 日 期 ： 200 6 - 5 - 11 无锡市好达电子有限公司 Shoulder Electronics Limited 客户确认 C USTOMER RECEIVED: 审核 C HECKED 批准 APPROVED 日期 D ATE
SAW FILTER HDF 2 20 A SMD - 3 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 2 of 8 更改历史记录 History Record 更改日期 Date 规格书编号 Spec . No . 产品型号 Part No . 客户产品型号 Customer No . 更改内容描述 Mod ify Content 备注 Remark
SAW FILTER HDF 2 20 A SMD - 3 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 3 of 8 1. SCOPE This specification shall cover the characteristics of SAW filter With HDF 220 A used for the page system. 2 . ELECTRICAL SPECIFICATION DC V oltage VDC 10V AC V oltage Vpp 10V50Hz/60Hz Operation temperature - 40 ℃ to +85 ℃ Storage temperature - 45 ℃ to +85 ℃ RF Power Dissipation 0dBm Electronic Characteristics 2 - 1.Typical frequency response 2 - 2.Electrical characteristics PART NUMBER HDF220A UNIT NOMINAL CENTERREQUENCY(Fo) 220.0 MHz INSERTION LOSS: 1. Fo - 100MHz TO – 42.5MHz 2. Fo±1.5MHz 3. Fo+39.5 T O +100MHz
50.0 MIN
4.0 MIN
RIPPLE (Fo±1.5MHz) 2.0 MAX dB INPUT AND OUTPUT IMPEDANCE 50/0 Ω /pF
SAW FILTER HDF 2 20 A SMD - 3 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 4 of 8 4. TEST CIRCUIT 4. DIMENSION Marking ： HDF 218 HD: Brand F : Filter 218 : No. 5. ENVIRONMENTAL CHARACTERISTICS 5 - 1 Temperature cycling Subject the device to a low temperature of - 40 ℃ for 30 minutes. Following by a high temp erature of +25 ℃ for 5 Minutes and a higher temperature of +85 ℃ for 30 Minutes. Then release the device into the room conditions for 1 to 2 hours prior to the me a surement. It shall meet the specifications in 2 - 2 . 5 - 2 Resistance to solder heat Submerge th e device terminals into the solder bath at 260 ℃ ± 5 ℃ for 10 ± 1 sec. Then release the device into the room conditions for 4 hours. It shall meet the specifications 1. Ground 2. Input/output 3. Ground 4. Ground 5. Ground 6. Input/output 7. Ground 8. Ground
SAW FILTER HDF 2 20 A SMD - 3 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 5 of 8 in 2 - 2 . 5 - 3 Solderability Submerge the device terminals into the solder bath at 245 ℃ ± 5 ℃ for 5s, More than 95% area of the soldering pad must be covered with new solder. It shall meet the specifications in 2 - 2 . 5 - 4 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in 2 - 2 . 5 - 5 Vibration Subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in 2 - 2 . 6. REMARK
6.1 Static voltage
Static voltage between signal load & ground may cause det e rioration &destruction of the component. Please avoid static voltage.
6.2 Ultrasonic cleaning
Ultrasonic vibration may cause det e ri oration & destruction of the component. Please avoid ultrason ic cleaning
6.3 Soldering
Only leads of component may be soldered. Please avoid soldering another part of component. 7. Packing
7.1 Dimensions
(1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be d amaged during transportation and storage.
7.2 Reeling Quantity
1000 pcs/reel 7’’ 3000 pcs/reel 13’’
7.3 Taping Structure
(1) The tape shall be wound around the reel in the direction shown below.
SAW FILTER HDF 2 20 A SMD - 3 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 6 of 8 (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. 8. TAPE SPECIFICATIONS 8.1 Tensile Strength of Carrier Tape: 4.4N/mm width
8.2 Top Cover Tape Adhesion (See the below figure)
(1) pull off angle: 0~ 15 º (2) speed: 300mm/min.
SAW FILTER HDF 2 20 A SMD - 3 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 7 of 8 (3) force: 20~70g [Figure 1] Carrier Tape Dimensions [Unit:mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.0 ± 0.3 5.5 ± 0.05 1.75 ± 0.1 4.0 ± 0.1 8.0 ± 0.1 2.0 ± 0.05 Ø 1.5 ± 0.1 Ø 1.0 ± 0.25 0.3 ± 0.05 2.10 ± 0.1 6.40 ± 0.1 5.20 ± 0.1 [Fig ure 2]
SAW FILTER HDF 2 20 A SMD - 3 www.shoulder.cn Tel:0755 - 82916880 Fax:0755 - 82916881 E - mail: info@shoulder.cn Page 8 of 8 [Unit:mm] A B C D E W t r Ø 330 ± 1.0 Ø 100 ± 0.5 Ø 13 ± 0.5 Ø 21 ± 0.8 ± 0.5 ± 0.3 max. 1.0 max.