HD29050P

HD29050 RENESAS | Alldatasheet

Document overview

• Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 14

Technical content

Features

• Built in current restriction when short circuit
• Power up/down protection.
• High output current I OH = –40 mA IOL = 40 mA Receiver
• Input hysteresis (Typ. 50 mV)
• In phase input voltage ±200 mV of input sensitivity in the range –7 to +12 V.
• Ordering Information Part Name Package Type Package Code Package Abbreviation Taping Abbreviation (Quantity) HD29050P DILP-16 pin DP-16E, -16FV P — Pin Arrangement (Top view) R1B GND R1A R1Y R2Y R Enable R2A R2B

16 VCC

Rev.3.00, Jul.16.2004, page 2 of 13 Function Table Drivers Receivers Input A Enable Output Y Output Z Differential Input A – B Enable Output Y LH L H V ID ≥ 0.2 V L H H H H L –0.2 V < V ID < 0.2 V L ? XLZ Z V ID ≤ –0.2 V H Z XH Z H : High level L : Low level Z : High impedance X : Immaterial ? : Irrelevant Absolute Maximum Ratings Item Symbol Ratings Unit Supply Voltage*1 VCC 7V Input Voltage A, B*3 VIN ±25 V Differential Input Voltage*2*3 VID ±25 V Output Current*3 IO 50 mA Enable Input Voltage V IE 5.5 V Input Voltage*4 VIN 5.5 V Output Applied Voltage*4*5 VO –1.0 to 7.0 V Operating Temperature Range Topr 0 to 70 °C Storage Temperature Range Tstg –65 to 150 °C Notes: 1. All voltage values except for differential input voltage are with respect to network ground terminal. 2. Differential input voltage is measured at the noninverting input with respect to the corresponding inverting input. 3. Only receiver 4. Only driver 5. Z state 6. The absolute maximum ratings are values which must not individually be exceeded, and furthermore, no two of which may be realized at the same time. Recommended Operating Conditions Item Symbol Min Typ Max Unit Supply Voltage V CC 4.75 5.0 5.25 V In Phase Input Voltage*1 VIC –7.0 — 12 V Differential Input Voltage*1 VID –6.0 — 6.0 V Enable Input Voltage V IE 0 — 5.25 V Input Voltage*2 VIN 0 — 5.25 V Operating Temperature Topr 0 25 70 °C Notes: 1. Only receiver 2. Only driver

Rev.3.00, Jul.16.2004, page 3 of 13 Electrical Characteristics (Ta = 0 to +70°C) Driver Item Symbol Min Typ Max Unit Conditions Input Voltage V IHD 2.0 — — V VILD ——0 . 8 V Input Clamp Voltage V IKD — — –1.5 V V CC = 4.75 V, II = –18 mA Output Voltage V OHD 2.5 — — V V CC = 4.75 V, IOH = –20 mA 2.4 — — V V CC = 4.75 V, IOH = –40 mA VOLD ——0 . 4 5 V V CC = 4.75 V, IOL = 20 mA ——0 . 5 V V CC = 4.75 V, IOL = 40 mA Output Leak Current I OZD –100 — 100 µA V CC = 5.25 V, VO = 0.5 V, Enable = 0.8 V –100 — 100 µA V CC = 5.25 V, VO = 2.7 V, Enable = 0.8 V IO (Off) — — –100 µA V CC = 0 V, VO = –0.25 V — — –100 µA V CC = 0 V, VO = 6.0 V Input Current I ID — — 100 µA V CC = 5.25 V, VI = 5.25 V IIHD ——2 0µ A V CC = 5.25 V, VI = 2.7 V IILD — — –360 µA V CC = 5.25 V, VI = 0.4 V Differential Output Voltage ∆ |VOC| ——0 . 4 V |VOD2|2 . 0 — — V Short Circuit Output Current*1 IOSD –30 — –150 mA V CC = 5.25 V, VO = 0 V

Rev.3.00, Jul.16.2004, page 4 of 13 Electrical Characteristics (Ta = 0 to +70°C) Receiver Item Symbol Min Typ Max Unit Conditions Differential Input Threshold Voltage*2 VTHR ——0 . 2 V V O ≥ 2.7 V –7.0 V < VIC < 12 V –7.0 V < VIC < 12 V Input Current I IBR ——1 . 0 m A V IN = 12 V, 0 V ≤ V CC ≤ 5.25 V — — –0.8 mA V IN = –7 V, 0 V ≤ V CC ≤ 5.25 V Output Voltage V OHR 2.7 — — V V CC = 4.75 V, IO = –400 mA VID = 0.4 V,–7.0 V < VICM < 12 V VOLR ——0 . 4 5 V V CC = 4.75 V, IO = 8.0 mA VID = –0.4 V, –7.0 V < VICM < 12 V Output Leak Current I OZR –100 — 100 mA V CC = 5.25 V, VO = 0.4 V VID = 3.0 V, Enable = 2.0 V –100 — 100 mA V CC = 5.25 V, VO = 2.4 V VID = –3.0 V, Enable = 2.0 V Short Circuit Output Current*1 IOSR –15 — –85 mA V CC = 5.25 V, VO = 0 V VID = 3.0 V Input Voltage V IHE 2.0 — — V VILE ——0 . 8 V Input Current I ILE — — –100 µA V CC = 5.25 V, VIL = 0.4 V IIHE ——2 0µ A V CC = 5.25 V, VIH = 2.7 V IIE — — 100 µA V CC = 5.25 V, VIH = 5.25 V Input Clamp Voltage V IKE — — –1.5 V V CC = 4.75, II = –18 mA Supply Item Symbol Min Typ Max Unit Conditions Supply Current I CC —5 5 *3 80 mA V CC = 5.25 V Notes: 1. Not more than one output should be shorted at a time, and duration of the short circuit should not exceed one second. 2. In this table, only the threshold voltage is expressed in algebra. 3. All typical values are at V CC = 5 V, Ta = 25°C.

Rev.3.00, Jul.16.2004, page 5 of 13 Switching Characteristics (Ta = 25°C, VCC = 5 V) Driver Item Symbol Min Typ Max Unit Conditions Propagation Delay Time t PLHD ——2 0n s C L = 30 pF, RL = 75 Ω to GND RL = 180 Ω to VCC tPHLD ——2 0n s C L = 30 pF, RL = 75 Ω to GND RL = 180 Ω to VCC Propagation Delay Time Difference tSKD*1 ——4 n s C L = 30 pF, RL = 75 Ω to GND RL = 180 Ω to VCC Output Enable Time t ZHD ——2 0n s C L = 30 pF, RL = 75 Ω to GND tZLD ——3 5n s C L = 30 pF, RL = 180 Ω to VCC Output Disable Time t HZD ——2 0n s C L = 10 pF, RL = 75 Ω to GND tLZD ——2 5n s C L = 10 pF Receiver Item Symbol Min Typ Max Unit Conditions Propagation Delay Time t PLHR ——4 0n s C L = 15 pF tPHLR ——4 0n s C L = 15 pF Output Enable Time t ZHR ——2 0n s C L = 15 pF, RL = 5 KΩ to GND tZLR ——2 5n s C L = 15 pF, RL = 2 KΩ to VCC Output Disable Time t HZR ——3 0n s C L = 15 pF, RL = 5 KΩ to GND RL = 2 KΩ to VCC tLZR ——3 0n s Note: 1. t SKD = |tPLHD – tPHLD|

Rev.3.00, Jul.16.2004, page 6 of 13 Output Y Output Z 50 Ω 50 Ω V 2OD Y Z 50 Ω 50 Ω R VOC Note: |V OD| and ∆ |VOC| indicate the differences of voltage from the former states when Y and Z outputs are inversed. 1. tPLHD, tPHLD Test circuit Input A Y Z Output R = 180 L Ω R = L Ω 5 V C = 30 pF L Enable 3 V Pulse Generator

Rev.3.00, Jul.16.2004, page 7 of 13 Waveforms Input A 10 % 90 % tr tf 1.3 V 90 % 0 V 3 V 1.3 V 10 % Output Y tPHLD tPLHD tPLHD tPHLD 1.3 V 1.3 V OH VOL V 1.3 V 1.3 V VOH VOL Output Z tSKD tSKD 2. tZHD, tZLD, tHZD, tLZD Test circuit Input A Enable Y Z Output R = 180 L Ω R = L Ω 5 V

3 V or GND

C = 30 pF or 10 pF L Pulse Generator

Rev.3.00, Jul.16.2004, page 8 of 13 Waveforms Input Enable 1.3 V 1.3 V 3 V 0 V Output tZHD tHZD VOL OHV 1.3 V 0.5 V tZLD tLZD OHV 1.3 V VOL 0.5 V 10 % 90 % tr 90 % 10 % tf 3. tPLHR, tPHLR Test circuit Input A Enable C = 15 pF LB Output 1.5 V Pulse Generator

Rev.3.00, Jul.16.2004, page 9 of 13 Waveforms Input A 10 % 90 % tr tf 1.5 V 90 % 0 V 3 V 1.5 V 10 % Output Y tPLHR tPHLR 1.3 V 1.3 V VOH VOL 4. tZHR, tZLR, tHZR, tLZR Test circuit Input Enable A B 5 V +1.5 V or -1.5 V C = 15 pF L Output Va R = 5 k L Ω R = 2 k L Ω Pulse Generator

Rev.3.00, Jul.16.2004, page 10 of 13 Waveforms Input Enable 1.5 V 1.5 V 3 V 0 V Output Y tZHR tHZR VOL OHV 1.5 V 0.5 V tZLR tLZR OHV 1.5 V VOL 0.5 V 10 % 90 % tr 90 % tf 10 % Notes: 1. The pulse generator has the following characteristics: PRR = 1 MHz, 50% duty cycle, tr = tf = 6.0 ns. 2. C L includes probe and jig capacitance. 3. 75 Ω connected between the pin and GND at tZHD tHZD test. 180 Ω connected between the pin and GND at tZHD tHZD test. 4. At t HZR, tLZR test, S1 and S2 are closed. At tZHR test, S1 is open and S2 is closed. At tZLR test, S1 is closed and S2 is open.

Rev.3.00, Jul.16.2004, page 11 of 13 Main Characteristics 0 –40 V = 5.25 VCC T = 25a °C –80 –120 –160 –200 5.00 V 4.75 V 1.0 0 20 V = 5.25 VCC T = 25a °C 0.8 0.6 0.4 0.2 40 60 80 100 V = 5.00 VCC V = 4.75 VCC 0 –20 V = 5.25 VCC T = 25a °C –40 –60 –80 –100 5.00 V 4.75 V 1.0 0 10 V = 5.25 VCC T = 25 °Ca 0.8 0.6 0.4 0.2 20 30 40 V = 5.00 VCC V = 4.75 VCC Output Current (IOH) [mA] Output Characteristics (High level) [Driver] Output Voltage (VOH) [V] Output Current (IOL) [mA] Output Characteristics (Low level) [Driver] Output Voltage (VOL) [V] Output Current (IOH) [mA] Output Characteristics (High level) [Receiver] Output Voltage (VOH) [V] Output Current (IOL) [mA] Output Characteristics (Low level) [Driver] Output Voltage (VOL) [V]

Rev.3.00, Jul.16.2004, page 12 of 13 0–200 V = 0 VIA V = 5 VCC –100 01 0 0 200 V +TV –T T = 25a °C Input Voltage (VU) [mV] Input / Output Characteristics [Receiver] Output Voltage (VOUT) [V]

Rev.3.00, Jul.16.2004, page 13 of 13 Package Dimensions 19.2

20.32 Max

6.3 7.4 Max5.06 Max2.54 Min

0.51 Min

(reference value) DP-16E Conforms Conforms 1.05 g 0.89 1.3 7.62 0.25 + 0.1 – 0.05 0˚ – 15˚ As of January, 2003 Unit: mm 19.2 6.3 7.4 Max5.06 Max2.54 Min (reference value) DP-16FV Conforms Conforms 1.05 g 2.54 ± 0.25 *NI/Pd/AU Plating *0.48 ± 0.08 0.89 1.3 7.62 *0.25 ± 0.06 0˚ – 15˚ Unit: mm

Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Renesas Technology Europe Limited. Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900 Renesas Technology Europe GmbH Dornacher Str. 3, D-85622 Feldkirchen, Germany Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11 Renesas Technology Hong Kong Ltd. 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2375-6836 Renesas Technology Taiwan Co., Ltd. FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan Renesas Technology (Shanghai) Co., Ltd. 26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China Renesas Technology Singapore Pte. Ltd. 1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 RENESAS SALES OFFICES © 2004. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .1.0