HCTS163MS INTERSIL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 9

Technical content

Features

  • 3 Micron Radiation Hardened CMOS SOS
  • Total Dose 200K RAD (Si)
  • SEP Effective LET No Upsets: >100 MEV-cm 2/mg
  • Single Event Upset (SEU) Immunity < 2 x 10-9 Errors/Bit-Day (Typ)
  • Dose Rate Survivability: >1 x 1012 RAD (Si)/s
  • Dose Rate Upset: >1010 RAD (Si)/s 20ns Pulse
  • Latch-Up Free Under Any Conditions
  • Fanout (Over Temperature Range) - Standard Outputs 10 LSTTL Loads
  • Military Temperature Range: -55 oC to +125oC
  • Significant Power Reduction Compared to LSTTL ICs
  • DC Operating Voltage Range: 4.5V to 5.5V
  • LSTTL Input Compatibility - VIL = 0.8V Max - VIH = VCC/2 Min
  • Input Current Levels Ii≤ 5µA at VOL, VOH

Description

The Intersil HCTS163MS is a Radiation Hardened synchronous presettable counter that feature look-ahead carry logic for use in high speed counting application. HCTS163MS is a binary counter, and is reset synchronously with the clock. Counting and parallel presetting are both accomplished synchronously with the negative to positive transition of the clock. The HCTS163MS utilizes advanced CMOS/SOS technology to achieve high-speed operation. This device is a member of radiation hardened, high-speed, CMOS/SOS Logic Family. The HCTS163MS is supplied in a 16 lead Ceramic flatpack (K suffix) or a SBDIP Package (D suffix). September 1995 Spec Number 518600 File Number 2480.2 DB NA

Reset (clear) l XXXXLL Parallel Load h (Note 3) X X l l L L h (Note 3) X X l h H (Note 1) Count h (Note 3) h h h (Note 3) X Count (Note 1) Inhibit h (Note 3) X l (Note 2) X h (Note 3) X Qn (Note 1) h (Note 3) X X l (Note 2) h (Note 3) X Qn L H = HIGH Voltage Level L = LOW Voltage Level h = HIGH voltage level one setup time prior to the LOW-to-HIGH clock transition l = LOW voltage level one setup time prior to the LOW-to-HIGH clock transition X = Immaterial q = Lower case letter indicate the state of the referenced output prior to the LOW-to-HIGH clock transition = LOW-to-HIGH clock transition NOTES: 1. The TC output is HIGH when TE is HIGH and the counter is at terminal count (HLLH for 162 and HHHH for 163) 2. The HIGH-to-LOW transition of PE or TE on the 54/74163 and 54/74160 should only occur while CP is high for conventional operation 3. The LOW-to-HIGH transition of SPE orMR on the 54/74163 should only occur while CP is high for conventional operation CP P MR CP P MR CP P MR CP P MR Q3Q2 1314 PE TE SPE MR CP TC Q0 Q1 Q2 Q3 VCC TE TE D0 D1 D2 D3 Spec Number 518600

under “Electrical Performance Characteristics” are the only conditions recommended for satisfactory device operation. TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS

  1. All voltages referenced to device GND.
  2. For functional tests, VO≥ 4.0V is recognized as a logic “1”, and VO ≤ 0.5V is recognized as a logic “0”.

TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS

  1. All voltages referenced to device GND.
  2. AC measurements assume RL = 500Ω , CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = 3V.

TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS

  1. The parameters listed in Table 3 are controlled via design or process parameters. Min and Max Limits are guaranteed but not directly

tested. These parameters are characterized upon initial design release and upon design changes which affect these characteristics. TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS

  1. All voltages referenced to device GND.
  2. AC measurements assume RL = 500Ω , CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = 3V.
  3. For functional tests VO≥ 4.0V is recognized as a logic “1”, and VO≤ 0.5V is recognized as a logic “0”.

TABLE 5. BURN-IN AND OPERATING LIFE TEST, DELTA PARAMETERS (+25 TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)

TABLE 6. APPLICABLE SUBGROUPS

  1. Alternate group A testing in accordance with method 5005 of MIL-STD-883 may be exercised.

TABLE 7. TOTAL DOSE IRRADIATION

  1. Except FN test which will be performed 100% Go/No-Go.

TABLE 8. STATIC AND DYNAMIC BURN-IN TEST CONNECTIONS

  1. Each pin except VCC and GND will have a resistor of 10KΩ± 5% for static burn-in
  2. Each pin except VCC and GND will have a resistor of 1KΩ± 5% for dynamic burn-in

TABLE 9. IRRADIATION TEST CONNECTIONS NOTE: Each pin except VCC and GND will have a resistor of 47KΩ± 5% for irradiation testing. Group E, Subgroup 2, sample size is 4 dice/wafer 0 failures.

Intersil Space Level Product Flow - ‘MS’ Wafer Lot Acceptance (All Lots) Method 5007 (Includes SEM) GAMMA Radiation Verification (Each Wafer) Method 1019,

4 Samples/Wafer, 0 Rejects

100% Nondestructive Bond Pull, Method 2023 Sample - Wire Bond Pull Monitor, Method 2011 Sample - Die Shear Monitor, Method 2019 or 2027 100% Internal Visual Inspection, Method 2010, Condition A 100% Temperature Cycle, Method 1010, Condition C,

10 Cycles

100% Constant Acceleration, Method 2001, Condition per Method 5004 100% PIND, Method 2020, Condition A 100% External Visual 100% Serialization 100% Initial Electrical Test (T0) 100% Static Burn-In 1, Condition A or B, 24 hrs. min., +125 oC min., Method 1015 100% Interim Electrical Test 1 (T1) 100% Delta Calculation (T0-T1) 100% Static Burn-In 2, Condition A or B, 24 hrs. min., +125 oC min., Method 1015 100% Interim Electrical Test 2 (T2) 100% Delta Calculation (T0-T2) 100% PDA 1, Method 5004 (Notes 1and 2) 100% Dynamic Burn-In, Condition D, 240 hrs., +125 oC or Equivalent, Method 1015 100% Interim Electrical Test 3 (T3) 100% Delta Calculation (T0-T3) 100% PDA 2, Method 5004 (Note 2) 100% Final Electrical Test 100% Fine/Gross Leak, Method 1014 100% Radiographic, Method 2012 (Note 3) 100% External Visual, Method 2009 Sample - Group A, Method 5005 (Note 4) 100% Data Package Generation (Note 5) NOTES: 1. Failures from Interim electrical test 1 and 2 are combined for determining PDA 1. 2. Failures from subgroup 1, 7, 9 and deltas are used for calculating PDA. The maximum allowable PDA = 5% with no more than 3% of the failures from subgroup 7. 3. Radiographic (X-Ray) inspection may be performed at any point after serialization as allowed by Method 5004. 4. Alternate Group A testing may be performed as allowed by MIL-STD-883, Method 5005. 5. Data Package Contents:

  • Cover Sheet (Intersil Name and/or Logo, P.O. Number, Customer Part Number, Lot Date Code, Intersil Part Number, Lot Number, Quantity).
  • Wafer Lot Acceptance Report (Method 5007). Includes reproductions of SEM photos with percent of step coverage.
  • GAMMA Radiation Report. Contains Cover page, disposition, Rad Dose, Lot Number, Test Package used, Specification Numbers, Test equipment, etc. Radiation Read and Record data on file at Intersil.
  • X-Ray report and film. Includes penetrometer measurements.
  • Screening, Electrical, and Group A attributes (Screening attributes begin after package seal).
  • Lot Serial Number Sheet (Good units serial number and lot number).
  • Variables Data (All Delta operations). Data is identified by serial number. Data header includes lot number and date of test.
  • The Certificate of Conformance is a part of the shipping invoice and is not part of the Data Book. The Certificate of Conformance is signed by an authorized Quality Representative. Spec Number 518600

All Intersil semiconductor products are manufactured, assembled and tested underISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web sitehttp://www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee

1130 Brussels, Belgium

TEL: (32) 2.724.2111 ASIA Intersil (Taiwan) Ltd. Taiwan Limited 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029 HCTS163MS AC Timing Diagrams AC VOLTAGE LEVELS PARAMETER HCTS UNITS VCC 4.50 V VIH 3.00 V VS 1.30 V VIL 0 V GND 0 V VS INPUT OUTPUT OUTPUT TTHL 80% 20% 80% 20% VIH VIL VOH VOL VOH VOL TPLH TPHL VS TTLH AC Load Circuit DUT TEST CL RL POINT CL = 50pF RL = 500Ω Spec Number 518600

DIE DIMENSIONS: 104 x 86 mils METALLIZATION: Type: AlSi Metal Thickness: 11k Å ± 1kÅ GLASSIVATION: Type: SiO2 Thickness: 13kÅ ± 2.6kÅ WORST CASE CURRENT DENSITY: < 2.0 x 105A/cm2 BOND PAD SIZE: 100µm x 100µm 4 mils x 4 mils Metallization Mask Layout HCTS163MS NOTE: The die diagram is a generic plot from a similar HCS device. It is intended to indicate approximate die size and bond pad location. The mask series for the HCTS163 is TA14448A. MRCP P0 (3) P1 (4) P2 (5) P3 (6) (8) PE (7) VCC (14) Q0 (13) Q1 (12) Q2 (11) Q3 (10)(9) (15) TC (2) (1) (16) TESPEGND Spec Number 518600