HCS245MS INTERSIL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 7

Technical content

Features

  • 3 Micron Radiation Hardened CMOS SOS
  • Total Dose 200K or 1 Mega-RAD(Si)
  • Latch-Up Free Under Any Conditions
  • Fanout (Over Temperature Range) - Bus Driver Outputs - 15 LSTTL Loads
  • Military Temperature Range: -55 oC to +125oC
  • Significant Power Reduction Compared to LSTTL ICs
  • DC Operating Voltage Range: 4.5V to 5.5V
  • LSTTL Input Compatibility - VIL = 0.8V Max - VIH = VCC/2 Min
  • Input Current Levels Ii≤ 5µA at VOL, VOH

Description

The Intersil HCS245MS is a Radiation Hardened Non-Invert- ing Octal Bidirectional Bus Transceiver, Three-State, intended for two-way asynchronous communication between data busses. The HCS245MS allows data transmission from the A bus to the B bus or from the B bus to the A bus. The logic level at the direction input (DIR) determines the data direction. The output enable input ( OE) puts the I/O port in the high-impedance state when high. The HCS245MS utilizes advanced CMOS/SOS technology to achieve high-speed operation. This device is a member of radiation hardened, high-speed, CMOS/SOS Logic Family. The HCS245MS is supplied in a 20 lead Weld Seal Ceramic flatpack (K suffix) or a Weld Seal Ceramic Dual-In-Line Package (D suffix). File Number 2468.1 December 1992 Functional Diagram ONE OF 8 TRANSCEIVERS B DATA (18, 17, 16, 15, 14, 13, 12) DIR OUTPUT ENABLE A DATA (2, 3, 4, 5, 6, 7, 8) TO OTHER

7 BUFFERS

H = High Voltage Level, L = Low Voltage Level, X = Immaterial To prevent excess currents in the High-Z (Isolation) modes, all I/O terminals should be terminated with 10kΩ to 1MΩ resistors.

under “Electrical Performance Characteristics” are the only conditions recommended for satisfactory device operation. TABLE 1. DC. ELECTRICAL PERFORMANCE CHARACTERISTICS

  1. All voltages reference to device GND.
  2. For functional tests, VO≥ 4.0V is recognized as a logic “1”, and VO ≤ 0.5V is recognized as a logic “0”.

TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS

  1. All voltages referenced to device GND.
  2. AC measurements assume RL = 500Ω , CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = VCC.

TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS

  1. The parameters listed in Table 3 are controlled via design or process parameters. Min and Max Limits are guaranteed but not directly

tested. These parameters are characterized upon initial design release and upon design changes which affect these characteristics. TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS

  1. All voltages referenced to device GND.
  2. AC measurements assume RL = 500Ω , CL = 50pF, Input TR = TF = 3ns, VIL = GND, VIH = VCC.
  3. For functional tests, VO≥ 4.0V is recognized as a logic “1”, and VO ≤ 0.5V is recognized as a logic “0”.

TABLE 5. BURN-IN AND OPERATING LIFE TEST, DELTA PARAMETERS (+25 TABLE 6. APPLICABLE SUBGROUPS

  1. Alternate Group A testing in accordance with Method 5005 of MIL-STD-883 may be exercised.

TABLE 7. TOTAL DOSE IRRADIATION

  1. Except FN test which will be performed 100% Go/No-Go.

TABLE 4. DC POST RADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued)

TABLE 8. STATIC BURN-IN AND DYNAMIC BURN-IN TEST CONNECTIONS

  1. Each pin except VCC and GND will have a resistor of 10KΩ± 5% for static burn-in.
  2. Each pin except VCC and GND will have a resistor of 680Ω± 5% for dynamic burn-in.

TABLE 9. IRRADIATION TEST CONNECTIONS group 2, sample size is 4 dice/wafer 0 failures.

All Intersil semiconductor products are manufactured, assembled and tested underISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web sitehttp://www.intersil.com HCS245MS Three-State Low Timing Diagrams TRI-STATE LOW VOLTAGE LEVELS PARAMETER HCS UNITS VCC 4.50 V VIH 4.50 V VS 2.25 V VT 2.25 V VW 0.90 V GND 0 V VS INPUT OUTPUT VIH VIL VOZ VOL TPZL TPLZ VT VW Three-State High Timing Diagrams TRI-STATE HIGH VOLTAGE LEVELS PARAMETER HCS UNITS VCC 4.50 V VIH 4.50 V VS 2.25 V VT 2.25 V VW 3.60 V GND 0 V VS INPUT OUTPUT VIH VIL VOH VOZ TPZH TPHZ VT VW Three-State Low Load Circuit DUT TEST CL RL POINT CL = 50pF RL = 500Ω VCC Three-State High Load Circuit DUT TEST RL POINT CL = 50pF RL = 500Ω File Number

DIE DIMENSIONS: 124 x 110 mils METALLIZATION: Type: AlSi Metal Thickness: 11k Å ± 1kÅ GLASSIVATION: Type: SiO2 Thickness: 13kÅ ± -2.6kÅ DIE ATTACH: Material: Silver Epoxy WORST CASE CURRENT DENSITY: <2.0 x 105A/cm2 BOND PAD SIZE: 100µm x 100µm 4 mils x 4 mils Metallization Mask Layout HCS245MS DIR (1) A0 (2) (8) (13) B5 VCC (20)NC NC NC NC OE (19) A1 (3) A2 (4) A3 (5) A4 (6) A5 (7) (9) GND (10) (11) (12) (14) B4 (15) B3 (16) B2 (17) B1 (18) B0