HCS200

HCS200 MICROCHIP | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 16

Technical content

Ó 1996 Microchip Technology Inc. Preliminary DS40138A-page 1

FEATURES

• Programmable 28-bit serial number
• Programmable 64-bit encryption key
• Each transmission is unique
• 66-bit transmission code length
• 32-bit hopping code
• 28-bit serial number, 4-bit function code, V LOW indicator transmitted
• Encryption keys are read protected Operating
• 3.5–13.0V operation
• Three button inputs - seven functions available
• Selectable baud rate
• Automatic code word completion
• Battery low signal transmitted to receiver
• Non-volatile synchronization data Other
• Easy to use programming interface
• On-chip EEPROM
• On-chip oscillator and timing components
• Button inputs have internal pulldown resistors
• Low external component cost Typical Applications The HCS200 is ideal for Remote Keyless Entry (RKE) applications. These applications include:
• Fixed code replacement
• Automotive RKE systems
• Automotive alarm systems
• Automotive immobilizers
• Gate and garage door openers
• Identity tokens
• Burglar alarm systems

DESCRIPTION

The HCS200, from Microchip Technology Inc., is a code hopping encoder designed for Remote Keyless Entry (RKE) systems. The HCS200 utilizes the Keeloq Ò code hopping technology, which incorporates high security, a small package outline and low cost, to make this device a perfect solution for replacement of fixed code devices in unidirectional remote keyless entry systems and access control systems. PACKAGE TYPES BLOCK DIAGRAM The HCS200 combines a 32-bit hopping code generated by a non-linear encryption algorithm, with a 28-bit serial number and 6 information bits to create a 66-bit transmission stream. The length of the transmission eliminates the threat of code scanning, and the code hopping mechanism makes each transmission unique, thus rendering code capture and resend schemes useless. The encryption key, serial number, and configuration data are stored in EEPROM which is not accessible via any external connection. This makes the HCS200 a very secure unit. The HCS200 provides an easy to use serial interface for programming the necessary security keys, system parameters, and configuration data. All encryption keys and code combinations are pro- grammable but read-protected. The keys can only be verified after an automatic erase and programming operation. This protects against attempts to gain access to keys and manipulate synchronization values. VDD PWM VSS PDIP, SOIC NC NC HCS200 Vss VDD Oscillator Reset circuit Controller Power latching and switching Button input port 32-bit shift register EncoderEEPROM PWM S2 S1 S0 HCS200 K EE L OQ Ò Code Hopping Encoder* KeeLoq is a trademark of Microchip Technology Inc. This document was created with FrameMaker404

Ó 1996 Microchip Technology Inc. The HCS200 operates over a wide voltage range of 3.5 volts to 13.0 volts and has three button inputs in an 8-pin configuration. This allows the system designer the freedom to utilize up to seven functions. The only components required for device operation are the but- tons and RF circuitry, allowing a very low system cost.

1.0 SYSTEM OVERVIEW

• Man ufacturer’s code — a 64-bit word, unique to each manufacturer, used to produce a unique encryption key in each transmitter (encoder).
• Encr yption Key — a unique 64-bit key generated and programmed into the encoder during the manufacturing process. The encryption key controls the encryption algorithm and is stored in EEPROM on the encoder device.

1.1 Learn

The HCS product family facilitates several learn strate- gies to be implemented on the decoder. The following are examples of what can be done. It must be pointed out that their exists some third-party patents on learn- ing strategies and implementation.

1.1.1 NORMAL LEARN

The receiver uses the same information that is transmit- ted during normal operation to derive the transmitter’s secret key, decrypt the discrimination value and the synchronization counter.

1.1.2 SECURE LEARN*

The transmitter is activated through a special button combination to transmit a stored 48-bit value (random seed) that can be used for key generation or be part of the key. Transmission of the random seed can be dis- abled after learning is completed. The HCS200 is a code hopping encoder device that is designed specifically for keyless entry systems, primarily for vehicles and home garage door openers. It is meant to be a cost-effective, yet secure solution to such systems. The encoder portion of a keyless entry system is meant to be carried by the user and operated to gain access to a vehicle or restricted area. The HCS200 requires very few external components (Figure 2-1). Most low-end keyless entry systems transmit the same code from a transmitter every time a button is pushed. The number of possible code combinations for a low end system is also a relatively small number. These shortcomings provide the means for a sophisticated thief to create a device that ‘grabs’ a transmission and re-transmits it later, or a device that scans all possible combinations until the correct one is found. The HCS200 employs the K EE L OQ code hopping encryption algorithm to achieve a high level of security. Code hopping is a method by which the code transmitted from the transmitter to the receiver is different every time a button is pushed. This method, coupled with a transmission length of 66 bits, virtually eliminates the use of code ‘grabbing’ or code ‘scanning’. As indicated in the block diagram on page one, the HCS200 has a small EEPROM array which must be loaded with several parameters before use. The most important of these values are:

• A 28-bit serial number which is meant to be unique for every encoder
• A 16-bit configuration value
• An encryption key that is generated at the time of production
• A 16-bit synchronization value The serial number for each transmitter is programmed by the manufacturer at the time of production. The generation of the encryption key is done using a key generation algorithm (Figure 1-1). Typically, inputs to the key generation algorithm are the serial number of the transmitter and a 64-bit manufacturer’s code. The manufacturer’s code is chosen by the system manufacturer and must be carefully controlled. The manufacturer’s code is a pivotal part of the overall system security. FIGURE 1-1: CREATION AND STORAGE OF ENCRYPTION KEY DURING PRODUCTION Transmitter Manufacturer’s Serial Number Code Encryption Key Key Generation Algorithm Serial Number Encryption Key Sync Counter HCS200 EEPROM Array * Code Hopping learn patents pending.

Ó 1996 Microchip Technology Inc. Preliminary DS40138A-page 3 HCS200 The 16-bit synchronization value is the basis for the transmitted code changing for each transmission, and is updated each time a button is pressed. Because of the complexity of the code hopping algorithm, a change in one bit of the synchronization value will result in a large change in the actual transmitted code. There is a relationship (Figure 1-2) between the key values in EEPROM and how they are used in the encoder. Once the encoder detects that a button has been pressed, the encoder reads the button and updates the synchro- nization counter. The synchronization value is then combined with the encryption key in the encryption algorithm and the output is 32 bits of encrypted infor- mation. This data will change with every button press, hence, it is referred to as the hopping portion of the code word. The 32-bit hopping code is combined with the button information and the serial number to form the code word transmitted to the receiver. The code word format is explained in detail in Section 4.3. Any type of controller may be used as a receiver, but it is typically a microcontroller with compatible firmware that allows the receiver to operate in conjunction with a transmitter based on the HCS200. Section 7.0 provides more detail on integrating the HCS200 into a total sys- tem. Before a transmitter can be used with a particular receiver, the transmitter must be ‘learned’ by the receiver. Upon learning a transmitter, information is stored by the receiver so that it may track the transmitter, including the serial number of the transmitter, the current synchronization value for that transmitter, and the same encryption key that is used on the transmitter. If a receiver receives a message of valid format, the serial number is checked, and, if it is from a learned transmitter, the message is decrypted, and the decrypted synchronization counter is checked against what is stored. If the synchronization value is verified, then the button status is checked to see what operation is needed. Figure 1-3 shows the relationship between some of the values stored by the receiver and the values received from the transmitter. FIGURE 1-2: BASIC OPERATION OF TRANSMITTER (ENCODER) FIGURE 1-3: BASIC OPERATION OF RECEIVER (DECODER) Button Press InformationEEPROM Array

32 Bits of

Encrypted Data Serial Number Transmitted Information Encryption Key Sync Counter Serial Number KeeLoq Encryption Algorithm Button Press Information EEPROM Array Encryption Key Encrypted DataSerial Number Received Information Decrypted Synchronization Counter Check for Match Check for Match Sync Counter Serial Number Manufacturer Code KEE LOQ Decryption Algorithm

Ó 1996 Microchip Technology Inc.

2.0 DEVICE OPERATION

As shown in Figure 2-1, the HCS200 is a simple device to use. It requires only the addition of buttons and RF circuitry for use as the transmitter in your security appli- cation. A description of each pin is described in Table 2-1. FIGURE 2-1: TYPICAL CIRCUITS TABLE 2-1: PIN DESCRIPTIONS Note: When V DD > 9.0V and driving low capacitive loads, a resistor with a minimum value of 50 W should be used in line with V DD . This prevents clamping of PWM at 9.0V in the event of PWM overshoot. Name Pin Number Description S0 1 Switch input 0 S1 2 Switch input 1 S2 3 Switch input 2/Clock pin when in programming mode V SS

5 Ground reference connection

PWM 6 Pulse width modulation (PWM) output pin/Data pin for program- ming mode V DD

8 Positive supply voltage connec-

4 button remote control (Note) B3 B2 B1 B0 +12V (Note 2) R +12V NC NC NC NC (Note 2) R Note 1: Up to 7 functions can be implemented by pressing more than one button simultaneously or by using a suitable diode array. 2: Resistor (R) is recommended for current limiting. The high security level of the HCS200 is based on the pat- ented K EE L OQ technology. A block cipher based on a block length of 32 bits and a key length of 64 bits is used. The algo- rithm obscures the information in such a way that even if the transmission information (before coding) differs by only one bit from the information in the previous transmission, the next coded transmission will be totally different. Statistically, if only one bit in the 32-bit string of information changes, approxi- mately 50 percent of the coded transmission will change. The HCS200 will wake up upon detecting a switch closure and then delay approximately 10 ms for switch debounce (Figure 2-2). The synchronization information, fixed informa- tion, and switch information will be encrypted to form the hop- ping code. The encrypted or hopping code portion of the transmission will change every time, even if the same button is pushed again. A code that has been transmitted will not occur again for more than 64K transmissions. This will provide more than 18 years of typical use before a code is repeated based on 10 operations per day. Overflow information sent from the encoder can be used by the decoder to extend the number of unique transmissions to more than 192K. If in the transmit process it is detected that a new button(s) has been pre ssed, a reset will immediately be forced and the code word will not be completed. Please note that but- tons removed will no t have any effect on the code word unless no buttons remain pressed in which case the code word will be completed and the power down will occur. FIGURE 2-2: ENCODER OPERATION Power Up Reset and Debounce Delay (10 ms) Sample Inputs Update Sync Info Encrypt With Load Transmit Register Buttons Added All Buttons Released (A button has been pressed) Transmit Stop No Ye s No Ye s Encryption Key Complete Code Word Transmission

Ó 1996 Microchip Technology Inc. Preliminary DS40138A-page 5 HCS200

3.0 EEPROM MEMORY

The HCS200 contains 192 bits (12 x 16-bit words) of EEPROM memory (Table 3-1). This EEPROM array is used to store the encryption key information, synchronization value, etc. Further descriptions of the memory array is given in the following sections. TABLE 3-1: EEPROM MEMORY MAP

3.1 Key_0 - Key_3 (64-Bit Encryption Key)

The 64-bit encryption key is used by the transmitter to create the encrypted message transmitted to the receiver. This key is created and programmed at the time of production using a key generation algorithm. The key generation algorithm may be different from the K EE L OQ algorithm. Inputs to the key generation algorithm are the serial number for the particular transmitter being used and the 64-bit manufacturer’s code. While the key generation algorithm supplied from Microchip is the typical method used, a user may elect to create their own method of key generation. This may be done providing that the decoder is programmed with the same means of creating the key for decryption purposes.

3.2 SYNC (Synchronization Counter)

This is the 16-bit synchronization value that is used to create the hopping code for transmission. This value will be changed after every transmission.

3.3 Reserved

Must be initialized to 0000H. WORD ADDRESS MNEMONIC DESCRIPTION

0 KEY_0 64-bit encryption key

(word 0)

1 KEY_1 64-bit encryption key

(word 1)

2 KEY_2 64-bit encryption key

(word 2)

3 KEY_3 64-bit encryption key

(word 3)

4 SYNC 16-bit synchronization

5 Reserved Set to 0000H

6 SER_0 Device Serial Number

(word 0)

7 SER_1 Device Serial Number

(word 1)

8 SEED_0 Seed Value (word 0)

9 SEED_1 Seed Value (word 1)

10 Reserved Set to 0000H

11 CONFIG Config Word

3.4 SER_0, SER_1

(Encoder Serial Number) SER_0 and SER_1 are the lower and upper words of the device serial number, respectively. Although there are 32 bits allocated for the serial number, only the lower order 28 bits are transmitted. The serial number is meant to be unique for every transmitter.

3.5 SEED_0, SEED_1 (Seed Word)

This is the 2-word (32-bit) seed code that will be transmitted when all three buttons are pressed at the same time. This allows the system designer to implement the secure learn feature or use this fixed code word as part of a different key generation/tracking process.

3.6 Configuration Word

The configuration word is a 16-bit word stored in EEPROM array that is used by the device to store information used during the encryption process, as well as the status of option configurations. Further explanations of each of the bits are described in the following sections. TABLE 3-2: CONFIGURATION WORD

3.6.1 DISCRIMINATION VALUE

(DISC0 TO DISC11) Bits 14 and 15 should be set to zero. The discrimination value can be programmed with any value to serve as a post decryption check on the decoder end. In a typical system, this will be programmed with the 12 least sig- nificant bits of the serial number or a constant value, which will also be stored by the receiver system after a transmitter has been learned. The discrimination bits are part of the information that form the encrypted por- tion of the transmission. After the receiver has decrypted a transmission, the discrimination bits can be checked against the stored value to verify that the decryption process was valid. Bit Number Bit Description

0 Discrimination Bit 0

1 Discrimination Bit 1

2 Discrimination Bit 2

3 Discrimination Bit 3

4 Discrimination Bit 4

5 Discrimination Bit 5

6 Discrimination Bit 6

7 Discrimination Bit 7

8 Discrimination Bit 8

9 Discrimination Bit 9

10 Discrimination Bit 10

11 Discrimination Bit 11

12 Voltage Trip Point Select (V

13 Baudrate Select Bit 0 (BSL0)

14 Reserved

15 Reserved

Ó 1996 Microchip Technology Inc.

3.6.2 BAUD RATE SELECT BITS (BSL0)

BSL0 selects the speed of transmission and the code word blanking. Table 3-3 shows how the bits are used to select the different baud rates and Section 5.2 pro- vides detailed explanation in code word blanking. TABLE 3-3: BAUD RATE SELECT

3.6.3 LOW VOLTAGE TRIP POINT SELECT

The low voltage trip point select bit is used to tell the HCS200 what V DD level is being used. This information will be used by the device to determine when to send the voltage low signal to the receiver. When this bit is set to a one, the V DD level is assumed to be operating from a 9.0 volt or 12.0 volt V DD level. If the bit is set low, then the V DD level is assumed to be 6.0 volts. Refer to Figure 3-1 for voltage trip point. V LOW is tested at 3.5V and 13.0V. FIGURE 3-1: VOLTAGE TRIP POINTS BY CHARACTERIZATION BSL0 Basic Pulse Element Code Words Transmitted 0 400 m s All 1 200 m s 1 out of 2 -40 20 40 100 8.5 7.5 8.0 7.0 9.0 VLOW Temp (C) Volts (V) VLOW sel = 1 -20 0 60 80 2.5 3.0 3.5 4.0 VLOW sel = 0 4.5 5.0 5.5 Max Min Max Min

4.0 TRANSMITTED WORD

4.1 Transmission Format

The HCS200 transmission is made up of several parts (Figure 4-1). Each transmission begins with a preamble and a header, followed by the encrypted and then the fixed data. The actual data is 66 bits which consists of 32 bits of encrypted data and 34 bits of fixed data. Each transmission is followed by a guard period before another transmission can begin. Refer to Table 8-4 for transmission timing requirements. The encrypted por- tion provides up to four billion changing code combina- tions and includes the button status bits (based on which buttons were activated) along with the synchroni- zation counter value and some discrimination bits. The fixed portion is comprised of the status bits, the function bits, and the 28-bit serial number. The fixed and encrypted sections combined increase the number of combinations to 7.38 x 10

4.2 Synchronous Transmission Mode

Synchronous transmission mode can be used to clock the code word out using an external clock. To enter synchronous transmission mode, the program- ming mode start-up sequence must be executed as shown in Figure 4-3. If either S1 or S0 is set on the fall- ing edge of S2, the device enters synchronous trans- mission mode. In this mode, it functions as a normal transmitter, with the exception that the timing of the PWM data string is controlled externally and that 16 extra bits are transmitted at the end with he code word. The button code will be the S0, S1 value at the falling edge S2. The timing of the PWM data string is con- trolled by supplying a clock on S2 and should not exceed 20 kHz. The code word is the same as in PWM mode with 16 reserved bits at the end of the word. The reserved bits can be ignored. When in synchronous transmission mode S2 should not be toggled until all internal processing has been completed as shown in Figure 4-3.

4.3 Code Word Organization

The HCS200 transmits a 66-bit code word when a button is pressed. The 66-bit word is constructed from a Fixed Code portion and an Encrypted Code portion (Figure 4-2). The Encrypted Data is generated from 3 button bits, 12 discrimination bits, and the 16-bit sync value (Figure 4-2). The Fixed Code Data is made up from 1 status bit, 1 fixed bit, 4 button bits, and the 28-bit serial number.

Ó 1996 Microchip Technology Inc.

5.0 SPECIAL FEATURES

5.1 Code Word Completion

Code word completion is an automatic feature that makes sure that the entire code word is transmitted, even if the button is released before the transmission is complete. The HCS200 encoder powers itself up when a button is pushed and powers itself down after the command is finished, if the user has already released the button. If the button is held down beyond the time for one transmission, then multiple transmissions will result. If another button is activated during a transmission, the active transmission will be aborted and the new code will be generated using the new button information.

5.2 Blank Alternate Code Word

Federal Communications Commission (FCC) part 15 rules specify the limits on fundamental power and harmonics that can be transmitted. Power is calculated on the worst case average power transmitted in a 100 ms window. It is therefore advantageous to minimize the duty cycle of the transmitted word. This can be achieved by minimizing the duty cycle of the individual bits and by blanking out consecutive words. Blank Alternate Code Word (BACW) is used for reducing the average power of a transmission (Figure 5-1). This is a selectable feature that is determined in conjunction with the baud rate selection bit BSL0. Using the BACW allows the user to transmit a higher amplitude transmission if the transmission length is shorter. The FCC puts constraints on the aver- age power that can be transmitted by a device, and BACW effectively prevents continuous transmission by only allowing the transmission of every second word. This reduces the average power transmitted and hence, assists in FCC approval of a transmitter device.

5.3 Seed Transmission

In order to increase the level of security in a system, it is possible for the receiver to implement what is known as a secure learn function. This can be done by utilizing the seed value on the HCS200 which is stored in EEPROM and can only be transmitted when all three button inputs are pressed at the same time (Table 5-1). Instead of the normal key generation method being used to create the encryption key, this seed value is used.

5.4 V LOW : Voltage LOW indicator

The VLOW bit is transmitted with every transmission (Figure 4-2 and Figure 8-5) and will be transmitted as a zero if the operating voltage is above the voltage trip point. The V LOW signal is transmitted so the receiver can give an indication to the user that the transmitter battery is low. FIGURE 5-1: BLANK ALTERNATE CODE WORD (BACW) TABLE 5-1: PIN ACTIVATION TABLE External Internal S2 S1 S0 S3 S2 S1 S0 Standby after CC 0 0 00000 Hop 0 010001 0 100010 0 110011 1 001100 1 011110 1 101110 F i x e d 1 111111 One Code Word BACW Disabled (All words transmitted) BACW Enabled (1 out of 2 transmitted) A 100ms 100ms 100ms 100ms Amplitude

Ó 1996 Microchip Technology Inc. Preliminary DS40138A-page 9 HCS200

6.0 PROGRAMMING THE HCS200

When using the HCS200 in a system, the user will have to program some parameters into the device including the serial number and the secret key before it can be used. The programming cycle allows the user to input all 192 bits in a serial data stream, which are then stored internally in EEPROM. Programming will be initiated by forcing the PWM line high, after the S2 line has been held high for the appropriate length of time line (Table 6-1 and Figure 6-1). After the program mode is entered, a delay must be provided to the device for the automatic bulk write cycle to complete. This will write all locations in the EEPROM to an all zeros pat- tern. The device can then be programmed by clocking in 16 bits at a time, using S2 as the clock line and PWM as the data in line. Data clocked in on falling edge of S2. After each 16-bit word is loaded, a programming delay of TWC is required for the internal program cycle to complete. At the end of the programming cycle, the device can be verified (Figure 6-2) by reading back the EEPROM. Reading is done by clocking the S2 line and reading the data bits on PWM. Falling edge of S2 initi- ated reading. For security reasons, it is not possible to execute a verify function without first programming the EEPROM. A verify operation can only be done immediately following the program cycle. Note: To ensure that the device does not acci- dentally enter programming mode (result- ing in a bulk erase), PWM should never be pulled high by the circuit connected to it. Special care should be taken when driving PNP RF transistors. TABLE 6-1: PROGRAMMING/VERIFY TIMING REQUIREMENTS FIGURE 6-1: PROGRAMMING WAVEFORMS FIGURE 6-2: VERIFY WAVEFORMS Parameter Symbol Min. Max. Units Program mode setup time T PS 3.5 4.5 ms Hold time 1 T PH 1 3.5 — ms Hold time 2 T PH 25 0 — ms Bulk Write time T PBW — 3.5 ms Program delay time T PROG — 3.5 ms Program cycle time T WC —3 6 m s Clock low time T CLKL 25 — ms Clock high time T CLKH 25 — ms Data setup time T DS 0 — ms Data hold time T DH 18 — ms Data out valid time T DV 10 24 ms PWM Enter Program Mode (Data) (Clock) Bit 0 Bit 1 Bit 2 Bit 3 Bit 14 Bit 15 Bit 16 Bit 17 TPH 1 TPBW TPS Repeat for each word (12 times) TPH 2 TCLKH TCLKL TWCTDS Data for Word 0 (KEY_0) Data for Word 1 TDH Note 1:Unused button inputs to be held to ground during the entire programming sequence. 2: The VDD pin must be taken to ground after a program/verify cycle. PWM (Clock) (Data) End of Programming Cycle Begin Verify Cycle Here Bit 1 Bit 2 Bit 3 Bit 15 Bit 14 Bit 16 Bit 17 Bit190 Bit191 TWC Data in Word 0 TDV Bit 0Bit191Bit190 Note: If a verify operation is to be done, then it must immediately follow the program cycle.

DS40138A-page 10 Preliminary Ó 1996 Microchip Technology Inc.

7.0 INTEGRATING THE HCS200

Use of the HCS200 in a system requires a compatible decoder. This decoder is typically a microcontroller with compatible firmware. Microchip will provide (via a license agreement) firmware routines that accept transmissions from the HCS200 and decrypt the hopping code portion of the data stream. These routines provide system designers the means to develop their own decoding system.

7.1 Learning a transmitter to a receiver

In order for a transmitter to be used with a decoder, the transmitter must first be ‘learned’. Several learning strategies can be followed in the decoder implementa- tion. When a transmitter is learned to a decoder, it is suggested that the decoder stores the serial number and current synchronization value in EEPROM. The decoder must keep track of these values for every transmitter that is learned (Figure 7-1). The maximum number of transmitters that can be learned is only a function of how much EEPROM memory storage is available. The decoder must also store the manufac- turer’s code in order to learn a transmission transmitter, although this value will not change in a typical system so it is usually stored as part of the microcontroller ROM code. Storing the manufacturer’s code as part of the ROM code is also better for security reasons. It must be stated that some learning strategies have been patented and care must be taken not to infringe. FIGURE 7-1: TYPICAL LEARN SEQUENCE Enter Learn Mode Wait for Reception of a Valid Code Generate Key from Serial Number Use Generated Key to Decrypt Compare Discrimination Value with Fixed Value Equal Wait for Reception of Second Valid Code Compare Discrimination Value with Fixed Value Use Generated Key to Decrypt Equal Counters Encryption key Serial number Synchronization counter Sequential Exit Learn successful. Learn Unsuccessful No No No Ye s Ye s Ye s Store:

Ó 1996 Microchip Technology Inc. Preliminary DS40138A-page 11 HCS200

7.2 Decoder operation

In a typical decoder operation (Figure 7-2), the key gen- eration on the decoder side is done by taking the serial number from a transmission and combining that with the manufacturer’s code to create the same secret key that was used by the transmitter. Once the secret key is obtained, the rest of the transmission can be decrypted. The decoder waits for a transmission and immediately can check the serial number to determine if it is a learned transmitter. If it is, it takes the encrypted portion of the transmission and decrypts it using the stored key It uses the discrimination bits to determine if the decryption was valid. If everything up to this point is valid, the synchronization value is evaluated. FIGURE 7-2: TYPICAL DECODER OPERATION Transmission Received Does Serial Number Match Decrypt Transmission Is Decryption Valid Is Counter Within 16 Is Counter Within 32K Update Counter Execute Command Save Counter in Temp Location Start No No No No Ye s Ye s Ye s Ye s Ye s No andNo

7.3 Synchronization with Decoder

The K EE LOQ technology features a sophisticated synchronization technique (Figure 7-3) which does not require the calculation and storage of future codes. If the stored counter value for that particular transmitter and the counter value that was just decrypted are within a formatted window of say 16, the counter is stored and the command is executed. If the counter value was not within the single operation window, but is within the double operation window of say 32K window, the trans- mitted synchronization value is stored in temporary location and it goes back to waiting for another trans- mission. When the next valid transmission is received, it will check the new value with the one in temporary storage. If the two values are sequential, it is assumed that the counter had just gotten out of the single opera- tion ‘window’, but is now back in sync, so the new syn- chronization value is stored and the command executed. If a transmitter has somehow gotten out of the double operation window, the transmitter will not work and must be re-learned. Since the entire window rotates after each valid transmission, codes that have been used are part of the ‘blocked’ (32K) codes and are no longer valid. This eliminates the possibility of grab- bing a previous code and re-transmitting to gain entry. FIGURE 7-3: SYNCHRONIZATION WINDOW Note: The synchronization method described in this section is only a typical implementation and because it is usually implemented in firmware, it can be altered to fit the needs of a particular system Blocked 32K Codes Open 32K Codes Entire Window rotates to eliminate use of previously used codes Current window of 16 codes CurrentPosition

DS40138A-page 12 Preliminary Ó 1996 Microchip Technology Inc.

8.0 ELECTRICAL CHARACTERISTICS

TABLE 8-1: ABSOLUTE MAXIMUM RATINGS TABLE 8-2: DC CHARACTERISTICS Symbol Item Rating Units VDD Supply voltage -0.3 to 13.3 V VIN Input voltage -0.3 to 13.3 V VOUT Output voltage -0.3 to V DD + 0.3 V IOUT Max output current 25 mA TSTG Storage temperature -55 to +125 °C (Note) TLSOL Lead soldering temp 300 °C (Note) VESD ESD rating 4000 V Note: Stresses above those listed under “ABSOLUTE MAXIMUM RATINGS” may cause permanent damage to the device. Commercial (C): Tamb = 0°C to +70°C Industrial (I): Tamb = -40°C to +85°C 3.5V < VDD < 13.0V Parameter Sym. Min Typ* Max Unit Conditions Operating current (avg) I CC 0.6 1.5 8.0 1.0 3.0 12.0 mA V DD = 3.5V VDD = 6.6V VDD = 13.0V Standby current I CCS 11 0 mA High level Input voltage VIH 0.4 VDD VDD + 0.3 V Low level input voltage V IL -0.3 0.15 V DD V High level output voltage VOH 0.5VDD VI OH = -2.0mA Low level output voltage V OL 0.08 V DD VI OL = 2.0mA Resistance; S0-S2 R S0-2 40 60 80 K W VIN = 4.0V Resistance; PWM R PWM 80 120 160 K W VIN = 4.0V Note: Typical values are at 25°C.

Ó 1996 Microchip Technology Inc. Preliminary DS40138A-page 13 HCS200 FIGURE 8-1: TYPICAL ICC CURVE OF HCS200 WITH EXTERNAL RESISTORS 23456789 1 1 1 2 1310 mA 0.0 2.0 4.0 6.0 8.0 10.0 12.0 VBAT [V] 2 3 4 5 6 7 8 9 1 11 21 3 10 mA 0.0 2.0 4.0 6.0 8.0 10.0 12.0 VBAT [V] 2 3 4 5 6 7 8 9 1 11 21 3 10 mA 0.0 2.0 4.0 6.0 8.0 10.0 12.0 VBAT [V] 50W 1K External 2K External Typical Maximum Minimum LEGEND

DS40138A-page 14 Preliminary Ó 1996 Microchip Technology Inc. FIGURE 8-2: POWER UP AND TRANSMIT TIMING TABLE 8-3: POWER UP AND TRANSMIT TIMING REQUIREMENTS FIGURE 8-3: PWM FORMAT FIGURE 8-4: PREAMBLE/HEADER FORMAT VDD = +3.5 to 13.0V Commercial (C): Tamb = 0°C to +70°C Industrial (I): Tamb = -40°C to +85°C Parameter Symbol Min Max Unit Remarks Time to second button press T BP 10 + Code Word 26 + Code Word ms (Note 1) Transmit delay from button detect T TD 10 26 ms Debounce Delay T DB 61 5 m s Auto-shutoff time-out period T TO 20 120 s (Note 2) Note 1: TBP is the time in which a second button can be pressed without completion of the first code word and the intention was to press the combination of buttons. 2: The auto-shutoff time-out period is not tested. Button Press Sn Detect TDB PWM TTD Code Word Transmission TTO Code Word Code Word Code Word Code Word n TBP LOGIC ‘0’ LOGIC ‘1’ Preamble Header Encrypted Portion of Transmission Fixed portion of Transmission Guard Time TP TH THOP TFIX TG TBP TE TE TE Preamble Header P0 P12

23 TE 10 TE

DS40138A-page 16 Preliminary Ó 1996 Microchip Technology Inc. HCS200 Product Identification System To order or to obtain information (e.g., on pricing or delivery), please use the listed part numbers, and refer to the factory or the listed sales offices. Package: P = Plastic DIP (300 mil Body), 8-lead SN = Plastic SOIC (150 mil Body), 8-lead Temperature Blank = 0°C to +70°C Range: I = -40°C to +85°C Device: HCS200 Code Hopping Encoder HCS200T Code Hopping Encoder (Tape and Reel) HCS200 - /P AMERICAS (continued) San Jose Microchip Technology Inc.

2107 North First Street, Suite 590

San Jose, CA 95131 Tel: 408 436-7950 Fax: 408 436-7955 Toronto Microchip Technology Inc.

5925 Airport Road, Suite 200

Mississauga, Ontario L4V 1W1, Canada Tel: 905 405-6279Fax: 905 405-6253 ASIA/PACIFIC Hong Kong Microchip Technology Rm 3801B, Tower Two Metroplaza,

223 Hing Fong Road,

Kwai Fong, N.T., Hong Kong Tel: 852 2 401 1200 Fax: 852 2 401 3431 Korea Microchip Technology 168-1, Y oungbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku, Seoul, Korea Tel: 82 2 554 7200 Fax: 82 2 558 5934 Singapore Microchip Technology

200 Middle Road

#10-03 Prime Centre Singapore 188980 Tel: 65 334 8870 Fax: 65 334 8850 Taiwan Microchip Technology 10F-1C 207 Tung Hua North Road Taipei, Taiwan, ROC Tel: 886 2 717 7175 Fax: 886 2 545 0139 EUROPE United Kingdom Arizona Microchip Technology Ltd. Unit 6, The Courtyard Meadow Bank, Furlong Road Bourne End, Buckinghamshire SL8 5AJ Tel: 44 1 628 850303 Fax: 44 1 628 850178 France Arizona Microchip Technology SARL Zone Industrielle de la Bonde

2 Rue du Buisson aux Fraises

91300 Massy - France

Tel: 33 1 69 53 63 20 Fax: 33 1 69 30 90 79 Germany Arizona Microchip Technology GmbH Gustav-Heinemann-Ring 125 D-81739 Muenchen, Germany Tel: 49 89 627 144 0 Fax: 49 89 627 144 44 Italy Arizona Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041, Agrate Brianza, Milan Italy Tel: 39 39 689 9939 Fax: 39 39 689 9883 JAPAN Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shin Y okohama Kohoku-Ku, Y okohama Kanagawa 222 Japan Tel: 81 45 471 6166 Fax: 81 45 471 6122 6/14/96 AMERICAS Corporate Office Microchip Technology Inc. 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 602 786-7200 Fax: 602 786-7277 Technical Support: 602 786-7627 Web: http://www.microchip.com Atlanta Microchip Technology Inc.

500 Sugar Mill Road, Suite 200B

Atlanta, GA 30350 Tel: 770 640-0034 Fax: 770 640-0307 Boston Microchip Technology Inc.

5 Mount Royal Avenue

Marlborough, MA 01752 Tel: 508 480-9990 Fax: 508 480-8575 Chicago Microchip Technology Inc.

333 Pierce Road, Suite 180

Itasca, IL 60143 Tel: 708 285-0071 Fax: 708 285-0075 Dallas Microchip Technology Inc.

14651 Dallas Parkway, Suite 816

Dallas, TX 75240-8809 Tel: 214 991-7177 Fax: 214 991-8588 Dayton Microchip Technology Inc. Suite 150 Two Prestige Place Miamisburg, OH 45342 Tel: 513 291-1654 Fax: 513 291-9175 Los Angeles Microchip Technology Inc.

18201 Von Karman, Suite 1090

Irvine, CA 92715 Tel: 714 263-1888 Fax: 714 263-1338 New York Microchip Technology Inc.

150 Motor Parkway, Suite 416

Hauppauge, NY 11788 Tel: 516 273-5305 Fax: 516 273-5335 Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. No repre- sentation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not autho- rized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. All rights reserved. All other trademarks mentioned herein are the property of their respective companies. All rights reserved. Ó 1996, Microchip Technology Inc.,USA, 5/96