HCPL-0600

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 30

Technical content

Features

 15 kV/µs minimum Common Mode Rejection (CMR) at VCM= 1 kV for HCNW2611, HCPL-2611, HCPL-4661, HCPL-0611, HCPL-0661  High speed: 10 MBd typical  LSTTL/TTL compatible  Low input current capability: 5 mA  Guaranteed AC and DC performance over temperature: –40°C to +85°C  Available in 8-Pin DIP , SOIC-8, widebody packages  Strobable output (single channel products only)  Safety approval – UL recognized – 3750 V rms for 1 minute and

5000 Vrms for 1 minute per UL1577 CSA approved

(5000 Vrms/1 Minute rating is for HCNW137/26X1 and Option 020 [6N137, HCPL-2601/11/30/31, HCPL-4661] products only) – IEC/EN/DIN EN 607 47-5-5 approved with:  VIORM = 567 Vpeak for 06xx Option 060  VIORM = 630 Vpeak for 6N137/26xx Option 060  VIORM =1414 Vpeak for HCNW137/26x1  MIL-PRF-38534 hermetic version available (HCPL- 56xx/66xx)

Applications

 Isolated line receiver  Computer-peripheral interfaces  Microprocessor system interfaces  Digital isolation for A/D, D/A conversion  Switching power supply  Instrument input/output isolation  Ground loop elimination  Pulse transformer replacement  Power transistor isolation in motor drives  Isolation of high speed logic systems CATHODE ANODE GND V V CC O 5ANODE 2 CATHODE 2 CATHODE 1 ANODE 1 GND V V CC V E V O1 6N137, HCPL-2601/2611 HCPL-0600/0601/0611 HCPL-2630/2631/4661 HCPL-0630/0631/0661 NC NC LED ON OFF ON OFF ON OFF ENABLE H H L L NC NC OUTPUT L H H H L H TRUTH TABLE (POSITIVE LOGIC) LED ON OFF OUTPUT L H TRUTH TABLE (POSITIVE LOGIC) SHIELD SHIELD 6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL-0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL-2630, HCPL-2631, HCPL-4661 High CMR, High Speed TTL Compatible Optocouplers

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers The 6N137, HCPL-26xx, HCPL-06xx, HCPL-4661, HCNW137, and HCNW26x1 are suitable for high speed logic interfacing, input/output buffering, as line receivers in environments that conventional line receivers cannot tolerate and are recommended for use in extremely high ground or induced noise environments. Selection Guide

Ordering Information

HCPL-xxxx is UL Recognized with 3750 Vrms for 1 minute per UL1577. HCNWxxxx is UL Recognized with 5000 Vrms for 1 minute per UL1577. Minimum CMR Input On- Current (mA) Output Enable 8-Pin DIP (300 Mil) Small-Outline SO-8 Widebody (400 Mil) Hermetic dV/dt (V/µs) VCM (V) Single Channel Package Dual Channel Package Single Channel Package Dual Channel Package Single Channel Package Single and Dual Channel Packages 1000 10 5 YES 6N137 5,000 1,000 5 YES HCPL-0600 HCNW137 NO HCPL-2630 HCPL-0630 10,000 1,000 YES HCPL-2601 HCPL-0601 HCNW2601 NO HCPL-2631 HCPL-0631 15,000 1,000 YES HCPL-2611 HCPL-0611 HCNW2611 NO HCPL-4661 HCPL-0661 1,000 50 YES HCPL-2602a a. Technical data are on separate Broadcom publications. 3,500 300 YES HCPL-2612a 1,000 50 3 YES HCPL-261Aa HCPL-061Aa NO HCPL-263Aa HCPL-063Aa 1,000b b. 15 kV/µs with VCM = 1 kV can be achieved using Broadcom application circuit.3. 1,000 YES HCPL-261Na HCPL-061Na NO HCPL-263Na HCPL-063Na 1,000 50 12.5 c c. Enable is available for singl e channel products only, except for HCPL-193x devices. HCPL-193xa HCPL-56xxa HCPL-66xxa

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Table 1: Ordering Information Part Number Option Package Surface Mount Gull Wing Tape & Reel UL 5000 Vrms/ 1 Minute Rating IEC/EN/DIN EN 60747- 5-5 Quantity RoHS Compliant Non-RoHS Compliant 6N137 -000E No option 300mil DIP-8 50 per tube -300E #300 X X 50 per tube -500E #500 X X X 1000 per reel -020E #020 X 50 per tube -320E #320 X X X 50 per tube - 5 2 0 E # 5 2 0 XXXX 1 0 0 0 p e r r e e l -060E #060 X 50 per tube -560E -560 X X X X 1000 per reel HCPL-2601 -000E No option 300mil DIP-8 50 per tube -300E #300 X X 50 per tube -500E #500 X X X 1000 per reel -020E #020 X 50 per tube -320E #320 X X X 50 per tube - 5 2 0 E # 5 2 0 XXXX 1 0 0 0 p e r r e e l -060E #060 X 50 per tube -360E — X X X 50 per tube HCPL-2611 -000E No option 300mil DIP-8 50 per tube -300E #300 X X 50 per tube -500E #500 X X X 1000 per reel -020E #020 X 50 per tube -320E #320 X X X 50 per tube - 5 2 0 E # 5 2 0 XXXX 1 0 0 0 p e r r e e l -060E #060 X 50 per tube -360E #360 X X X 50 per tube -560E #560 X X X X 1000 per reel HCPL-2630 -000E No option 300mil DIP-8 50 per tube -300E #300 X X 50 per tube -500E #500 X X X 1000 per reel -020E #020 X 50 per tube -320E #320 X X X 50 per tube - 5 2 0 E - 5 2 0 XXXX 1 0 0 0 p e r r e e l HCPL-2631 HCPL-4661 -000E No option 300mil DIP-8 50 per tube -300E #300 X X 50 per tube -500E #500 X X X 1000 per reel -020E #020 X 50 per tube -320E #320 X X X 50 per tube - 5 2 0 E # 5 2 0 XXXX 1 0 0 0 p e r r e e l

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Combinations of Option 020 and Option 060 are not available. Example 1: HCPL-2611-560E to order product of 300-mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Example 2: HCPL-2630 to order product of 300-mil DIP package in tube packaging and non RoHS compliant. Option data sheets are available. Contact your Broadcom sales representative or authorized distributor for information. NOTE: The notation “#xxx” is used for existing products, while products launched since July 15, 2001 and RoHS compliant option use “-xxxE”. HCPL-0600 HCPL-0601 HCPL-0611 -000E No option SO-8 X 100 per tube -500E #500 X X 1500 per reel -060E #060 X X 100 per tube -560E #560 X X X 1500 per reel HCPL-0630 HCPL-0631 HCPL-0661 -000E No option SO-8 X 100 per tube -500E #500 X X 1500 per reel HCNW137 HCNW2601 HCNW2611 -000E No option 400 mil DIP-8 X X 42 per tube -300E #300 X X X X 42 per tube - 5 0 0 E # 5 0 0 XXXXX 7 5 0 p e r r e e l Table 1: Ordering Information (Continued) Part Number Option Package Surface Mount Gull Wing Tape & Reel UL 5000 Vrms/ 1 Minute Rating IEC/EN/DIN EN 60747- 5-5 Quantity RoHS Compliant Non-RoHS Compliant

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Schematic SHIELD VF USE OF A 0.1 PF BYPASS CAPACITOR CONNECTED AS CLOSE AS POSSIBLE BETWEEN PINS 5 AND 8 IS RECOMMENDED. IF ICC VCC VO GND IO VE IE 7 6N137, HCPL-2601/2611 HCPL-0600/0601/0611 HCNW137, HCNW2601/2611 SHIELD VF1 IF1 ICC VCC VO1 IO1 SHIELD VF2 IF2 VO2 GND IO2 HCPL-2630/2631/4661 HCPL-0630/0631/0661

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Package Outline Drawings 8-pin DIP Package1 (6N137, HCPL-2601/11/30/31, HCPL-4661) 1. JEDEC Registered Dat a (for 6N137 only). 1.080 ± 0.320 (0.043 ± 0.013) 2.54 ± 0.25 (0.100 ± 0.010) 0.51 (0.020) MIN. 0.65 (0.025) MAX. 4.70 (0.185) MAX. 2.92 (0.115) MIN. 5° TYP. 0.254 + 0.076 - 0.051 (0.010 + 0.003) - 0.002) 7.62 ± 0.25 (0.300 ± 0.010) 6.35 ± 0.25 (0.250 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) DIMENSIONS IN MILLIMETERS (INCHES). 5678 4321 *MARKING CODE LETTER FOR OPTION NUMBERS "L" = OPTION 020 "V" = OPTION 060 OPTION NUMBERS 300 AND 500 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 3.56 ± 0.13 (0.140 ± 0.005) EEE NNNN YYWW A TEST RATING CODEZ P DEVICE PART NUMBER UL LOGO SPECIAL PROGRAM CODE LEAD-FREE AVAGO LOT ID DATE CODE PIN 1

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers 8-pin DIP Package with Gull Wing Surface Mount Option 300 (6N137, HCPL-2601/ 11/30/31, HCPL-4661) 0.635 ± 0.25 9.65 ± 0.25 (0.380 ± 0.010) 0.635 ± 0.130 (0.025 ± 0.005) 7.62 ± 0.25 (0.300 ± 0.010) 5678 4321 9.65 ± 0.25 (0.380 ± 0.010) 6.350 ± 0.25 (0.250 ± 0.010) 1.016 (0.040) 1.27 (0.050) 10.9 (0.430) 2.0 (0.080) LAND PATTERN RECOMMENDATION 1.080 ± 0.320 (0.043 ± 0.013) 1.780 (0.070) MAX.1.19 (0.047) MAX. 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). 0.254 + 0.076 - 0.051 (0.010 + 0.003) - 0.002) NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 3.56 ± 0.13 (0.140 ± 0.005)

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Small-Outline SO-8 Package (HCPL-0600/01/11/30/31/61) 8-Pin Widebody DIP Package (HCNW137, HCNW2601/11) 8765 4321 5.994 ± 0.203 (0.236 ± 0.008) 3.937 ± 0.127 (0.155 ± 0.005) 0.406 ± 0.076 (0.016 ± 0.003) 1.270 (0.050) BSC 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.060) 45° X 0.432 (0.017) 0.228 ± 0.025 (0.009 ± 0.001) 0.305 (0.012) MIN.TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX. NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX. 0.203 ± 0.102 (0.008 ± 0.004) 0 ~ 7° YYWW• NNNN Z EEE TEST RATING CODE DEVICE PART NUMBER LEAD-FREE LOT ID DATE CODE PIN 1 5678 4321 11.23 ± 0.15 (0.442 ± 0.006) 1.80 ± 0.15 (0.071 ± 0.006) 5.10 (0.201) MAX. 1.55 (0.061) MAX. 2.54 (0.100) TYP. DIMENSIONS IN MILLIMETERS (INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 7° TYP. 0.254 + 0.076 - 0.0051 (0.010 + 0.003) - 0.002) 11.00 (0.433) 9.00 ± 0.15 (0.354 ± 0.006) MAX. 10.16 (0.400) TYP. 0.51 (0.021) MIN. 0.40 (0.016) 0.56 (0.022) 3.10 (0.122) 3.90 (0.154) NNNNNNNN YYWW• A EEE Z AVAGO TEST RATING CODE DATE CODE LOT ID DEVICE PART NUMBER LEAD-FREE PIN 1

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers 8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW137, HCNW2601/11) Reflow Soldering Profile The recommended reflow soldering conditions are per JEDEC Standard J-STD-020 (latest revision). Non-halide flux should be used. Regulatory Information The 6N137, HCPL-26xx/06xx/46xx, and HCNW137/26xx have been approved by the following organizations: Test Rating Code, Z Optional Identification Code L – Option x2x A – Avago V – Option x5x or x6x – UL Logo P – Special Program Code UL Recognized under UL 1577, Component Recognition Program, File E55361. IEC/EN/DIN EN 60747-5-5 CSA Approved under CSA Component Acceptance Notice #5, File CA 88324. 1.00 ± 0.15 (0.039 ± 0.006) 7° NOM. 12.30 ± 0.30 (0.484 ± 0.012) 0.75 ± 0.25 (0.030 ± 0.010) 11.00 (0.433) 5678 4321 11.23 ± 0.15 (0.442 ± 0.006) 9.00 ± 0.15 (0.354 ± 0.006) 1.3 (0.051) 13.56 (0.534) 2.29 (0.09) LAND PATTERN RECOMMENDATION 1.80 ± 0.15 (0.071 ± 0.006) 4.00 (0.158) MAX. 1.55 (0.061) MAX. 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 INCHES). NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX. 0.254 + 0.076 - 0.0051 (0.010 + 0.003) - 0.002) MAX.

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Insulation and Safety-Related Specifications Option 300 – Surface mount classification is Class A in accordance with CECC 00802. Parameter Symbol 8-pin DIP (300 Mil) SO-8 Widebod (400 Mil) Units Conditions Minimum External Air Gap (External Clearance) L(101) 7.1 4.9 9.6 mm Measured from input terminals to output terminals, shortest distance through air. Minimum External Tracking (External Creepage) L(102) 7.4 4.8 10.0 mm Measured from input terminals to output terminals, shortest distance path along body. Minimum Internal Plastic Gap (Internal Clearance) 0.08 0.08 1.0 mm Through insula tion distance, conductor to conductor, usually the direct distance between the photoemitter and photodetector inside the optocoupler cavity. Minimum Internal Tracking (Internal Creepage) NA NA 4.0 mm Measured from input terminals to output terminals, along internal cavity. Tracking Resistance (Comparative Tracking Index) CTI 200 200 200 V DIN IEC 112/VDE 0303 Part 1 Isolation Group IIIa IIIa IIIa Materi al Group (DIN VDE 0110, 1/89, Table 1)

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers IEC/EN/DIN EN 60747-5-5 Insulation Characteristics2 (HCPL-06xx Option 060 Only) 2. Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. Description Symbol Characteristic Units Installation classification per DIN VDE 0110, Table 1 for rated mains voltage ≤ 150 Vrms for rated mains voltage ≤ 300 Vrms for rated mains voltage ≤ 600 Vrms I-IV I-IV I-III Climatic Classification 40/85/21 Pollution Degree (DIN VDE 0110/39) 2 Maximum Working Insulation Voltage V IORM 567 V peak Input-to-Output Test Voltage, Method ba VIORM × 1.875 = VPR, 100% Production Test with tm = 1s, Partial Discharge < 5 pC a. Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-5, for a detailed description. VPR 1063 V peak Input-to-Output Test Voltage, Method aa VIORM ×1.6 = VPR, Type and Sample Test, tm = 10s, Partial Discharge < 5 pC VPR 907 V peak Highest Allowable Overvoltage (Transient Overvoltage, tini = 60s) V IOTM 6000 V peak Safety Limiting Values (Maximum values allowed in the event of a failure) Case Temperature Input Currentb Output Powerb b. Ratings apply to all devices except otherwise noted in the Package column. TS IS,INPUT PS,OUTPUT 150 150 600 mA mW Insulation Resistance at T S, VIO = 500V R S ≥ 109 

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers IEC/EN/DIN EN 60747-5-5 Insulation Characteristics3 (HCPL-26xx; 46xx; 6N13x Option 060 Only) 3. Isolation characteristics are guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in application Description Symbol Characteristic Units Installation classification per DIN VDE 0110, Table 1 for rated mains voltage ≤ 300 Vrms for rated mains voltage ≤ 450 Vrms I-IV I-IV Climatic Classification 40/85/21 Pollution Degree (DIN VDE 0110/39) 2 Maximum Working Insulation Voltage V IORM 630 V peak Input to Output Test Voltage, Method ba VIORM × 1.875 = VPR, 100% Production Test with tm = 1s, Partial Discharge < 5 pC a. Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-5, for a detailed description. VPR 1181 V peak Input to Output Test Voltage, Method aa VIORM × 1.6 = VPR, Type and sample test, tm = 10s, Partial Discharge < 5 pC VPR 1008 V peak Highest Allowable Overvoltage (Transient Overvoltage, tini = 60s) V IOTM 6000 V peak Safety Limiting Values (Maximum values allowed in the event of a failure) Case Temperature Input Current Output Power T S IS,INPUT PS,OUTPUT 175 230 600 mA mW Insulation Resistance at TS, VIO = 500V R S ≥ 109 

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers IEC/EN/DIN EN 60747-5-5 Insulation Characteristics4 (HCNW137/2601/

2611 Only)

1. Isolation characteristics ar e guaranteed only within the safety maximum ratings, which must be ensured by protective circuits in application. Description Symbol Characteristic Units Installation classification per DIN VDE 0110, Table 1 for rated mains voltage ≤ 600 Vrms for rated mains voltage ≤ 1000 Vrms I-IV I-III Climatic Classification 40/85/21 Pollution Degree (DIN VDE 0110/39) 2 Maximum Working Insulation Voltage V IORM 1414 V peak Input to Output Test Voltage, Method ba VIORM × 1.875 = VPR, 100% Production Test with tm = 1s, Partial Discharge < 5 pC a. Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, IEC/EN/DIN EN 60747-5-5, for a detailed description. VPR 2651 V peak Input to Output Test Voltage, Method aa VIORM × 1.6 = VPR, Type and sample test, tm = 10s, Partial Discharge < 5 pC VPR 2262 V peak Highest Allowable Overvoltage (Transient Overvoltage, tini = 60s) V IOTM 8000 V peak Safety Limiting Values (Maximum values allowed in the event of a failure) Case Temperature Input Current Output Power T S IS,INPUT PS,OUTPUT 150 400 700 mA mW Insulation Resistance at TS, VIO = 500V R S ≥109 

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Absolute Maximum Ratings5 No derating required up to 85°C. 5. JEDEC Registered Dat a (for 6N137 only). Parameter Symbol Packagea a. Ratings apply to all devices except otherwise noted in the Package column. Min. Max. Units Note Storage Temperature T S –55 125 °C Operating Temperatureb b. 0°C to 70°C on JEDEC Registration. TA –40 85 °C Average Forward Input Current I F Single 8-Pin DIP Single SO-8 Widebody —2 0 m A c c. Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not exceed 20 mA. Dual 8-Pin DIP Dual SO-8 —1 5 d, e d. Each channel. e. Peaking circuits may produce transient input currents up to 50 mA, 50 ns maximum pulse width, provided average current does not exceed 15 mA. Reverse Input Voltage V R 8-Pin DIP , SO-8 — 5 V d Widebody — 3 Input Power Dissipation P I Widebody — 40 mW Single 8-Pin DIP — 36 Dual 8-Pin DIP — 27 Supply Voltage (1 Minute Maximum) V CC —7 V Enable Input Voltage (not to exceed VCC by more than 500 mV) VE Single 8-Pin DIP Single SO-8 Widebody —V CC + 0.5 V Enable Input Current I E —5 m A Output Collector Current I O —5 0 m A d Output Collector Voltage V O —7 V d Output Collector Power Dissipation P O Single 8-Pin DIP Single SO-8 Widebody —8 5 m W Dual 8-Pin DIP Dual SO-8 —6 0 d, f f. Derate linearly above 80°C free-air temperature at a rate of 2.7 mW/°C for the SOIC-8 package. Lead Solder Temperature (Through Hole Parts Only) TLS 8-Pin DIP — 260°C for 10 s, 1.6 mm below seating plane Widebody — 260°C for 10s, up to seating plane Solder Reflow Temperature Profile (Surface Mount Parts Only) SO-8 and Option 300 —S e e Package Outline Drawings

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Recommended Operating Conditions Parameter Symbol Min. Max. Units Input Current, Low Level IFL a a. The off condition can also be guaranteed by ensuring that VFL ≤ 0.8V. 02 5 0 µ A Input Current, High Levelb b. Each channel. IFH c c. The initial switching thres hold is 5 mA or less. It is recommended that 6.3 mA to 10 mA be used for best performance and to permit at least a 20% LED degradation guardband. 51 5 m A Power Supply Voltage V CC 4.5 5.5 V Low Level Enable Voltaged d. For single channel products only. VEL 00 . 8V High Level Enable Voltaged VEH 2.0 V CC V Operating Temperature T A –40 85 °C Fan Out (at RL = 1 k)b N — 5 TTL Loads Output Pull-up Resistor R L 330 4 k 

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Electrical Specifications Over recommended temperature (TA =–40°C to +85°C) unless otherwise specified. All Typicals at VCC = 5V, TA = 25°C. All enable test conditions apply to single channel products only. See note. Table 2: Electrical Specifications Parameter Sym. Package Min. Typ. Max. Units Test Conditions Figure Note High Level Output Current IOH a All — 5.5 100 µA V CC = 5.5V, VE = 2.0V 1 b, c, d VO = 5.5V, IF = 250 mA Input Threshold Current ITH Single Channel Widebody —2 . 0 5 . 0 m A V CC = 5.5V, VE = 2.0V, VO = 0.6V, IOL (Sinking) = 13 mA 2, 3 d Dual Channel 2.5 Low Level Output Voltage VOL a 8-Pin DIP , SO-8 — 0.35 0.6 V V CC = 5.5V, VE = 2.0V, IF = 5 mA, IOL (Sinking) = 13 mA 2, 3, 4, b, d Widebody 0.4 High Level Supply Current ICCH Single Channel — 7.0 10.0* mA V E = 0.5V VCC = 5.5V, IF = 0 mA e —6 . 5 — V E = VCC, VCC = 5.5 V, IF = 0 mA Dual Channel — 10 15 Both Channels Low Level Supply Current ICCL Single Channel — 9.0 13.0* mA V E = 0.5V, VCC = 5.5V, IF = 10 mA f —8 . 5 — V E = VCC, VCC = 5.5V IF = 10 mA Dual Channel — 13 21 Both Channels High Level Enable Current IEH Single Channel — –0.7 –1.6 mA V CC = 5.5V, VE = 2.0V Low Level Enable Current IEL a —– 0 . 9 – 1 . 6 m A V CC = 5.5V, VE = 0.5V g High Level Enable Voltage VEH 2.0 — — V d Low Level Enable Voltage VEL —— 0 . 8V Input Forward Voltage VF 8-Pin DIP 1.4 1.5 1.75a VT A = 25°C, IF = 10 mA 6, 7 b SO-8 1.3 — 1.80 I F = 10 mA Widebody 1.25 1.64 1.85 T A = 25°C, IF = 10 mA 1.2 2.05 I F = 10 mA

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible OptocouplersInput Reverse Breakdown Voltage BVR a 8-Pin DIP , SO-8 5 — — V I R = 10 µA b Widebody 3 — — I R = 100 µA, TA = 25°C Input Diode Temperature Coefficient VF/ TA 8-Pin DIP , SO-8 — –1.6 — mV/°C I F = 10 mA 7 b Widebody — –1.9 — Input Capacitance C IN 8-Pin DIP , SO-8 — 60 — pF f = 1 MHz, V F = 0V b Widebody — 70 — a. JEDEC registered data for the 6N137. The JEDEC Registration s pecifies 0°C to +70°C. Broadcom specifies –40°C to +85°C. b. Each channel. c. The JEDEC registration for the 6N137 specifies a maximum I OH of 250 µA. Broadcom guarantees a maximum IOH of 100 µA. d. No external pull up is required for a high logic state on the enable input. If the VE pin is not used, tying VE to VCC will result in improved CMR performance. For single channel products only. e. The JEDEC registration for the 6N137 specifies a maximum I CCH of 15 mA. Broadcom guarantees a maximum ICCH of 10 mA. f. The JEDEC registration for the 6N137 specifies a maximum I CCL of 18 mA. Broadcom guarantees a maximum ICCL of 13 mA. Table 2: Electrical Specifications (Continued) Parameter Sym. Package Min. Typ. Max. Units Test Conditions Figure Note

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Switching Specifications (AC) Over Recommended Temperature (TA = –40°C to + 85°C), VCC = 5V, IF = 7.5 mA unless otherwise specified. All Typicals at TA = 25°C, VCC = 5V. Parameter Symbol Packagea a. Ratings apply to all devices except otherwise noted in the Package column. Min. Typ. Max. Units Test Conditions Figure Note Propagation Delay Time to High Output Level tPLH 20 48 75b b. JEDEC registered data for the 6N137. ns T A = 25°C RL = 350 CL = 15 pF 8, 9, 10 c, d, f c. Each channel. d. The tPLH propagation delay is measured from the 3.75 mA point on the falling edge of the input pulse to the 1.5V point on the rising edge of the output pulse.

100 R L = 350

CL = 15 pF Propagation Delay Time to Low Output Level tPHL 25 50 75* ns T A = 25°C RL = 350 CL = 15 pF c, e, f e. The tPHL propagation delay is measured from the 3.75 mA point on the rising edge of the input pulse to the 1.5V point on the falling edge of the output pulse. f. No external pull up is required for a high logic state on the enable input. If the VE pin is not used, tying VE to VCC will result in improved CMR performance. For single channel products only. CL = 15 pF Pulse Width Distortion |t PHL – tPLH|8 - P i n D I P SO-8 — 3.5 35 ns R L = 350 CL = 15 pF 8, 9, 10, f, g g. See Propagation Delay, Pulse-Width Distortion, and Propagation Delay Skew for more information. Widebody 40 Propagation Delay Skew t PSK — — 40 ns R L = 350 CL = 15 pF f, g, h h. tPSK is equal to the worst case difference in tPHL and/or tPLH that will be seen between units at any given temperature and specified test conditions. Output Rise Time (10-90%) t r —2 4— n s R L = 350 CL = 15 pF 12 c, f Output Fall Time (90-10%) t f —1 0— n s R L = 350 CL = 15 pF 12 c, f Propagation Delay Time of Enable from VEH to VEL tELH Single Channel —3 0— n s R L = 350, CL = 15 pF, VEL = 0V, VEH = 3V 13, 14 i i. The t ELH enable propagation delay is measured from the 1.5V point on the falling edge of the enable input pulse to the 1.5V point on the rising edge of the output pulse. Propagation Delay Time of Enable from VEL to VEH tEHL Single Channel —2 0— n s j j. The t EHL enable propagation delay is measured from the 1.5V point on the rising edge of the enable input pulse to the 1.5V point on the falling edge of the output pulse.

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Parameter Sym. Device Min. Typ. Units Test Conditions Figure Note Logic High Common Mode Transient Immunity |CMH| 6N137 1,000 10,000 V/µs |V CM| = 10V V CC = 5V, IF = 0 mA, VO(MIN) = 2V, RL = 350, TA = 25°C 15 a, b, c, d a. Each channel. b. CMH is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state (that is, VO > 2.0V). c. For sinusoidal voltages, (|dV CM | / dt)max = fCMVCM(p-p). d. No external pull up is required for a high logic state on the enable input. If the VE pin is not used, tying VE to VCC will result in improved CMR performance. For single channel products only. HCPL-2630 HCPL-0600/0630 HCNW137 5,000 10,000 — |V CM| = 1 kV HCPL-2601/2631 HCPL-0601/0631 HCNW2601 10,000 15,000 — |V CM| = 1 kV HCPL-2611/4661 HCPL-0611/0661 HCNW2611 15,000 25,000 — |V CM| = 1 kV Logic Low Common Mode Transient Immunity |CM L| 6N137 1,000 10,000 V/µs |V CM| = 10V V CC = 5V, IF = 7.5 mA, VO(MAX) = 0.8V, RL = 350,, TA = 25°C 15 a, c, d, e e. CML is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state (that is, VO <0 . 8 V ) . HCPL-2630 HCPL-0600/0630 HCNW137 5,000 10,000 — |V CM| = 1 kV HCPL-2601/2631 HCPL-0601/0631 HCNW2601 10,000 15,000 — |V CM| = 1 kV HCPL-2611/4661 HCPL-0611/0661 HCNW2611 15,000 25,000 — |V CM| = 1 kV

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Package Characteristics All Typicals at TA = 25°C. Parameter Sym. Package Min. Typ. Max. Units Test Conditions Figure Note Input-Output Insulation II-O a a. JEDEC registered data for the 6N137. The JEDEC Registration s pecifies 0°C to 70°C. Broadcom specifies –40°C to 85°C. Single 8-Pin DIP Single SO-8 — — 1 µA 45% RH, t = 5s, VI-O = 3 kVdc, TA = 25°C b, c b. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together. c. In accordance with UL1577, each optocoupler is proof tested b y applying an insulation test voltage ≥ 4500 Vrms for one second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/ EN/DIN EN 60747-5-5 Insulation Characteristics Table, if applicable. Input-Output Momentary With- stand Voltaged d. The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-5 Insulation Characteristics Table (if applicable), your equipment level safety specification or Broadcom Application Note 1074, Optocoupler Input-Output Endurance Voltage. VISO 8-Pin DIP , SO-8 3750 — — Vrms RH 50%, t = 1 min, TA = 25°C b, c Widebody 5000 — — b, e e. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 Vrms for one second (leakage detection current limit, II-O ≤ 5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/ EN/DIN EN 60747-5-5 Insulation Characteristics Table, if applicable. OPT 020f f. For 6N137, HCPL-2601/2611/2630/2631/4661 only. 5000 — — Input-Output Resistance R I-O 8-Pin DIP , SO-8 — 1012 —  VI-O = 500 Vdc, b, g, h g. Each channel. h. Measured between the LED anode and cathode shorted together a nd pins 5 through 8 shorted together. For dual channel products only. Widebody 1012 1013 —V I-O = 500 Vdc, TA = 25°C 1011 —— V I-O = 500 Vdc, TA = 100°C Input-Output Capacitance C I-O 8-Pin DIP , SO-8 — 0.6 — pF f = 1 MHz, TA = 25°C b, g, h Widebody — 0.5 0.6 Input-Input Insulation Leakage Current II-I Dual Channel — 0.005 — µA RH 45%, t = 5s, VI-I = 500V i i. Measured between pins 1 and 2 shorted together, and pins 3 an d 4 shorted together. For dual channel products only. Resistance (Input-Input) R I-I Dual Channel — 1011 —  RH 45%, t = 5s, VI-I = 500V i Capacitance (Input-Input) C I-I Dual 8-Pin DIP — 0.03 — pF f = 1 MHz i Dual SO-8 0.25

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Figure 8: Test Circuit for TPHL and TPLH OUTPUT V MONITORING NODE O +5 V 1PULSE GEN. Z = 50 W t = t = 5 ns O f IF LR R M CCV 0.1μF BYPASS *C L GND INPUT MONITORING NODE r SINGLE CHANNEL OUTPUT V MONITORING NODE O +5 V PULSE GEN. Z = 50 W t = t = 5 ns O f I F LR R M CCV 0.1μF BYPASS CL* GND INPUT MONITORING NODE r DUAL CHANNEL 1.5 V tPHL tPLH IF INPUT OV OUTPUT I = 7.50 mA F I = 3.75 mAF *CL IS APPROXIMATELY 15 pF WHICH INCLUDES PROBE AND STRAY WIRING CAPACITANCE.

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Figure 15: Test Circuit for Common Mode Transient Immunity and Typical Waveforms Figure 16: Thermal Derating Curve, Dependence of Safety Limiting Value with Case Temperature per IEC/EN/DIN EN 60747 5-5 +5 V

1 CCV

0.1 μF BYPASS GND OUTPUT V MONITORING NODE O PULSE GENERATOR Z = 50:O IF B A VFF CMV R L SINGLE CHANNEL +5 V 0.1 μF BYPASS GND OUTPUT V MONITORING NODE O PULSE GENERATOR Z = 50:O IF B A VFF CMV RL DUAL CHANNEL VO 0.5 V OV (MIN.) 5 V

0 V SWITCH AT A: I = 0 mAF

SWITCH AT B: I = 7.5 mAF CMV HCM CM L OV (MAX.) CMV (PEAK) VO OUTPUT POWER – PS, INPUT CURRENT – IS TS – CASE TEMPERATURE – °C 20050 400 12525 75 100 150 600 800 200 100 300 500 700 PS (mW) IS (mA) HCPL-2611 OPTION 060 175 OUTPUT POWER – PS, INPUT CURRENT – IS TS – CASE TEMPERATURE – °C 17550 400 12525 75 100 150 600 800 200 100 300 500 700 PS (mW) IS (mA) HCNWXXXX

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Figure 17: Recommended TTL/LSTTL to TTL/LSTTL Interface Circuit *DIODE D1 (1N916 OR EQUIVALENT) IS NOT REQUIRED FOR UNITS WITH OPEN COLLECTOR OUTPUT. VCC1 5 V GND 1 D1* I F VF SHIELD SINGLE CHANNEL DEVICE 390: 0.1 μF BYPASS 5 V GND 2 VCC2 470: 7VE VCC1 5 V GND 1 D1* SHIELD DUAL CHANNEL DEVICE CHANNEL 1 SHOWN 390: 0.1 μF BYPASS 5 V GND 2 VCC2 470: IF VF

6N137, HCNW137, HCNW2601, HCNW2611, HCPL-0600, HCPL-0601, HCPL- 0611, HCPL-0630, HCPL-0631, HCPL-0661, HCPL-2601, HCPL-2611, HCPL- 2630, HCPL-2631, HCPL-4661 Data Sheet High CMR, High Speed TTL Compatible Optocouplers Figure 19: Parallel Data Transmission Example DATA t PSK INPUTS CLOCK DATA OUTPUTS CLOCK t PSK

Broadcom, the pulse logo, Connecting everything, Avago Technologies, Avago, and the A logo are among the trademarks of Broadcom and/or its affiliates in the United States, certain other countries, and/or the EU. Copyright © 2014–2018 Broadcom. All Rights Reserved. The term “Broadcom” refers to Broadcom Limited and/or its subsidiaries. For more information, please visit www.broadcom.com. Broadcom reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. Information furnished by Broadcom is believed to be accurate and reliable. However, Broadcom does not assume any liability arising out of the application or use of this information, nor the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others.