M54HC4060 STMICROELECTRONICS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 12

Technical content

14 STAGE BINARY COUNTER/OSCILLATOR

(Plastic Package) ORDER CODES : M54HC4060F1R M74HC4060M1R M74HC4060B1R M74HC4060C1R F1R (Ceramic Package) M1R (Micro Package) C1R (Chip Carrier) PIN CONNECTIONS (top view) NC = No Internal Connecti on

DESCRIPTION

.HIGH SPEED fMAX = 58 MHz (TYP.) AT VCC =5V .LOW POWER DISSIPATION ICC =4 µA (MAX.) AT TA =2 5°C .HIGH NOISE IMMUNITY VNIH =V NIL =2 8%V CC (MIN.) .OUTPUT DRIVE CAPABILITY

10 LSTTL LOADS

.SYMMETRICAL OUTPUT IMPEDANCE |IOH |=IOL = 4 mA (MIN.) .BALANCED PROPAGATION DELAYS tPLH =tPHL .WIDE OPERATING VOLTAGE RANGE VCC (OPR) = 2 V TO 6 V .PIN AND FUNCTION COMPATIBLE WITH 4060B The M54/74HC4060 is a high speed CMOS 14- STAGE BINARY COUNTER/OSCILLATOR fabri- cated in silicon gate C2MOS technology. It has the same high speed performance of LSTTL combined with true CMOS low power consumption. It operates ten times faster than metal-gate C 2MOS IC (4060B) with the same power dissipation. The oscillator configuration allows design of either RC or crystal oscillator circuits. A high level on the CLEAR accomplishes the reset function, i.e. all counter outputs are made low and the oscillator is disabled. A negative transition on the clock input increments the counter. Ten kinds of divided output are pro- vided ; 4 to 10 and 12 to 14 stage inclusive. The maximum division available at Q12 is 1/16384 f os- cillator. The Ø 1 input and the CLEAR input are equipped with protection circuits against static discharge and transient excess voltage.

INPUT AND OUTPUT EQUIVALENT CIRCUIT TRUTH TABLE øI CLEAR FUNCTION XH COUNTER IS RESET TO ZERO STATE ø0 OUTPUT GOES TO HIGH LEVEL ø0 OUTPUT GOES TO LOW LEVEL L COUNT UP ONE STEP L NO CHANGE X: DON’T CARE LOGIC DIAGRAM M54/M74HC4060

PIN No SYMBOL NAME AND FUNCTION 1, 2, 3 Q12 to Q14 Counter Outputs 7, 5, 4, 6, 14, 13, 15 Q4 to Q10 Counter Outputs 9 øO External Capacitor Connection 10 øO External Resistor Connection 11 øI Clock Input/Oscillator Pin

12 CLEAR Master Reset

8 GND Ground (0V)

16 V CC Positive Supply Voltage

Symbol Parameter Value Unit VCC Supply Voltage -0.5 to +7 V VI DC Input Voltage -0.5 to V CC + 0.5 V VO DC Output Voltage -0.5 to V CC + 0.5 V IIK DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Source Sink Current Per Output Pin ± 25 mA ICC or IGND DC V CC or Ground Current ± 50 mA P D Power Dissipation 500 (*) mW Tstg Storage Temperature -65 to +150 oC TL Lead Temperature (10 sec) 300 oC Absolute MaximumRatings are those values beyond whichdamage tothe device may occu r. Functional operation under these condition isnotimplied. (*) 500 mW:≅ 65 oC derate to 300 mW by 10mW/oC: 65oCt o 8 5oC RECOMMENDED OPERATING CONDITIONS Symbol Parameter Value Unit VCC Supply Voltage 2 to 6 V VI Input Voltage 0 to V CC V VO Output Voltage 0 to V CC V Top Operating Temperature:M54HC Series M74HC Series -55 to +125 -40 to +85 oC oC tr,tf Input Rise and Fall Time V CC = 2 V 0 to 1000 ns VCC = 4.5 V 0 to 500 VCC = 6 V 0 to 400 M54/M74HC4060

(V) TA =2 5oC 54HC and 74HC -40 to 85oC 74HC -55 to 125oC 54HC VIH High Level Input Voltage 2.0 1.5 1.5 1.5 V4.5 3.15 3.15 3.15 6.0 4.2 4.2 4.2 V IL Low Level Input Voltage 2.0 0.5 0.5 0.5 V4.5 1.35 1.35 1.35 6.0 1.8 1.8 1.8 V OH High Level Output Voltage (Q Outputs) 2.0 V I = VIH or V IL IO =-20µA 1.9 2.0 1.9 1.9 V VOL Low Level Output Voltage (Q Outputs)

2.0 VI =

IO =2 0µA 0.0 0.1 0.1 0.1 V V OH High Level Output Voltage (øO, øO Output) 2.0 V I = VIH or V IL IO =-20µA 1.8 2.0 1.8 1.8 VOL Low Level Output Voltage (øO, øO Output) 2.0 V I = VIH or V IL IO =2 0µA 0.0 0.2 0.2 0.2 II Input Leakage Current 6.0 VI =V CC or GND ±0.1 ±1 ±1 µA ICC Quiescent Supply Current

6.0 V I =V CC or GND 4 40 80 µA

AC ELECTRICAL CHARACTERISTICS (CL =5 0p F ,I n p u ttr =t f =6n s ) Symbol Parameter Test Conditions Value UnitVCC (V) TA =2 5oC 54HC and 74HC -40 to 85oC 74HC -55 to 125oC 54HC tTLH tTHL Output Transition Time 2.0 30 75 95 110 ns4 . 5 8 1 51 92 2 6 . 0 7 1 31 61 9 tPLH tPHL Propagation Delay Time (øI - Q4) 2.0 170 300 375 450 ns4.5 41 60 75 90 6.0 30 51 64 76 t PD Propagation Delay Time Difference (Qn- Qn+1) 2.0 32 75 95 110 ns4 . 5 7 1 51 92 2 6 . 0 5 1 31 61 9 t PLH tPHL Propagation Delay Time (CLEAR - Qn) 2.0 85 195 245 295 ns4.5 23 39 49 59 6.0 17 33 42 50 f MAX Maximum Clock Frequency 2.0 6 12 5 4 ns4.5 30 50 24 20 6.0 35 65 28 24 tW(H) tW(L) Minimum Pulse Width (øI) 2.0 30 75 95 110 ns4 . 5 8 1 51 92 2 6 . 0 7 1 31 61 9 tW(H) Minimum Pulse Width (CLEAR) 2.0 30 75 95 110 ns4 . 5 8 1 51 92 2 6 . 0 7 1 31 61 9 tREM Minimum Removal Time 2.0 40 100 125 150 ns4.5 10 20 25 30 6 . 0 9 1 72 12 6 C IN Input Capacitance 5 10 10 10 pF C PD (*) Power Dissipation Capacitance 27 pF (*) CPD is defined as the value of the IC’s internal equivalent capac itance which is calculated from the operating current consump tion without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC (opr) = CPD •VCC •fIN +ICC M54/M74HC4060

TEST CIRCUIT ICC (Opr.) SWITCHING CHARACTERISTICS TEST CIRCUIT tPLH ,tPHL (CLOCK-Q) tW (CLOCK) t PHL (CLEAR-Qn), tW (CLEAR) tPLH . tPHL (Qn - Qn + 1) .Ø IINPUT tr=t f=6 n s DUTY = 50 % Note : When CR or crystal oscillation circuit is adopted, the dynam ic power dissipation will be greater than the measure d value from the test circuit shown left, because these oscillion circuits spend much supp ly current. M54/M74HC4060

TYPICAL CLOCK DRIVE CIRCUITS EXTERNAL CLOCK DRIVE TYPICAL CIRCUIT TYPICAL CRYSTAL CIRCUIT M54/M74HC4060

Plastic DIP16 (0.25) MECHANICAL DATA DIM. mm inch a1 0.51 0.020 B 0.77 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L 3.3 0.130 Z 1.27 0.050 P001C M54/M74HC4060

Ceramic DIP16/1 MECHANICAL DATA DIM. mm inch A 20 0.787 B 7 0.276 D 3.3 0.130 E 0.38 0.015 e3 17.78 0.700 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 H 1.17 1.52 0.046 0.060 L 0.22 0.31 0.009 0.012 M 0.51 1.27 0.020 0.050 N 10.3 0.406 P 7.8 8.05 0.307 0.317 Q 5.08 0.200 P053D M54/M74HC4060

SO16 (Narrow) MECHANICAL DATA DIM. mm inch A 1.75 0.068 a1 0.1 0.2 0.004 0.007 a2 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45 ° (typ.) D 9.8 10 0.385 0.393 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M 0.62 0.024 S8 ° (max.) P013H M54/M74HC4060

DIM. mm inch A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A M54/M74HC4060

Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specificationsmentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronicsproducts are not authorized foruse ascritical componentsin life support devices or systems without express written approval of SGS-THOMSON Microelectonics.  1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A M54/M74HC4060