HB215SKG03CE-JB NKK | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

Series HB2 Quiet Actuation Illuminated Pushbutton L-2 www.nkkswitches.com NKK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 General Specifications Electrical Capacity (Resistive Load) Logic Level (code G): 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Other Ratings Contact Resistance: 80 milliohms maximum Insulation Resistance: 500 megohms minimum @ 500V DC Dielectric Strength: 500V AC minimum for 1 minute minimum Mechanical Life: 100,000 operations minimum Electrical Life: 100,000 operations minimum Nominal Operating Force: 1.8 Newtons Materials & Finishes Housing: Glass fiber reinforced polyamide Base: Glass fiber reinforced polyamide Movable Contact: Phosphor bronze with gold plating Contact Terminals: Phosphor bronze with gold plating Lamp Terminals: Steel with silver plating Environmental Data Operating Temp Range: -25°C through +50°C (-13°F through +122°F) Humidity: 90 ~ 95% humidity for 240 hours @ 40 °C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Installation Cap Installation Force: 15N (3.37 lbf) maximum downward force on cap Soldering Time & Temperature: 3 seconds @ 350°C or 5 seconds @ 270 °C Process Seal: Not available Standards & Certifications UL Recognition The HB2 pushbuttons have not been tested for UL recognition or CSA certification. or CSA Certification: These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy.

Quiet Actuation Illuminated Pushbutton Series HB2 L-3NKK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 www.nkkswitches.com Distinctive Characteristics Quiet actuation combined with crisp tactile feedback suited for broadcast equipment. Full face illumination with choice of red/green or red/yellow bicolor LEDs, as well as simultaneous bicolor illumination which produces amber. Option of legends on caps or film insert. Compact design with short body 17.0mm (.669") from PCB to top of cap and 7.5mm (.295”) square cap. Sliding Twin Crossbar (STC) mechanism provides unequalled logic-level reliability, contact stability, smooth positive detent actuation, and long life. Crimped power terminals ensure secure PCB mounting and prevent dislodging during soldering. Suitable applications include broadcast, telecommunication, and medical equipment, as well as measuring instruments, etc. Actual Size

Series HB2 Quiet Actuation Illuminated Pushbutton L-4 www.nkkswitches.com NKK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 CONTACTS & TERMINALS Gold Contacts and G03 PC Terminals, Rated 0.4VA @ 28V AC/DC Clear Lens with White Diffuser Black Housing Gold Contacts and PC Terminals with 0.4VA @ 28V AC/DC Rating CAP COLORS JB Clear Lens/White Diffuser POLE

1 SPST

DESCRIPTION FOR TYPICAL ORDERING EXAMPLE HB215SKG03CF-JB TYPICAL SWITCH ORDERING EXAMPLE CIRCUIT

5 OFF (ON)

( ) = Momentary G03 SHAPE S Square Red/Green LED Square Shape SPST OFF-(ON) Circuit LEDS CE Red/Yellow CF Red/Green Amber can be achieved by simultaneous illumination of LEDs. JB HOUSING K Black CF

Quiet Actuation Illuminated Pushbutton Series HB2 L-5NKK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 www.nkkswitches.com R = E - VF IF Where: R E V F IF = Resistor Value (Ohms) = Source Voltage (V) = Forward Voltage (V) = Forward Current (mA) Plunger Position ( ) = Momentary Connected Terminals Throw & Switch/Lamp Schematics Normal Down Normal Down Pole Model SP HB215 OFF (ON) OPEN 1-2 SPST .307" Square BodyS POLE & CIRCUIT HOUSING SHAPE & COLOR Black HousingK Gold Contacts Logic Level 0.4VA maximum @ 28V AC/DCG03 Switch Terminal CONTACT MATERIALS, RATINGS, & TERMINALS Notes: Switch terminals are not marked on switch. Red LED terminal is marked with “R”. LED circuit is isolated and requires external power source. Lamp Terminal CE Electrical specifications are determined at a basic temperature of 25 °C. LED circuit is independent of switch operation. If the source voltage is greater than rated LED voltage, a ballast resistor must be connected in series with the LED. The circ uit diagram and formula above will assist in calculating the value of the required ballast resistor. Color Red/Yellow Red/Green Unit Forward Peak Current I FM 30/30 30/30 mA Continuous Forward Current I F 20/20 20/20 mA Forward Voltage V F 2.0/2.1 2.0/2.1 V Reverse Peak Voltage V RM 4/4 4/4 V Current Reduction Rate Above 25°C ∆IF 0.33/0.33 0.33/0.33 mA/ °C Ambient Temperature Range -25 °C ~ +50°C BICOLOR LEDS & SPECIFICATIONS CFLED is an integral part of the HB2 switch. VF I FR+ E PCB Footprint 3 (+) 4 (-) 5 (+) Red Yellow or Green (0.5) Sq .020 (0.4) .016 (3.5) .138 (0.5) Sq .020 (0.4) .016 (3.5) .138 (2.25) Typ .089 (0.85) Dia Typ .033 (1.0) Dia .039 (0.5) .020 (0.92) .036 (2.54) .100 (2.5) Typ .098 (1.0) Dia .039 CL

Series HB2 Quiet Actuation Illuminated Pushbutton L-6 www.nkkswitches.com NKK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 Clear Transparent LensJ CAP COLORS White Translucent DiffuserB Lens & Diffuser Material: Polycarbonate Lens Finish: Glossy Diffuser Finish: Frosted TYPICAL SWITCH DIMENSIONS Square Single Pole HB215SKG03CF-JB LEGENDS Recommended Print Method: Screen Print on Lens or Film Insert; Pad Print on Lens. Epoxy based ink is recommended. General information and basic specifications are presented here for customers who want to do their own legends. Suggested Printable Area for Lens and Film Insert Additional Methods Additional methods for legends are engraving the lens and laser printing on film inserts. Maximum depth for engraving is 0.3 mm (.012”) on the cap lens. Enamel paint is recommended to fill the engraved area. Insert Material and Thickness: Clear Polyester, 4 mil max. Shaded area is printable area. 1. To order caps with legends, contact the factory and request the HB2 Legend Packet. 2. Once you determine your desired legend, fill out the ordering work sheet included in the packet. 3. Return the completed work sheet to receive a quotation. LEGEND PACKET AT3081 Square Lens AT3082 Square Diffuser Lens Film Insert (7.5) Sq .295 (17.0) .669 (3.1) .122 (1.4) .055 (0.92) .036 (2.54) .100 (3.5) .138 (0.4) .016 (11.7) .461 (0.8) Dia Typ .031 (4.5) .177 (0.5) Sq Typ .020 (5.0) .197 (0.5) .020 (0.5) Sq Typ .020 (7.8) Sq .307 R (3.5) .138 (7.5) Sq .295 (1.0) .039 (5.8) Sq .228 UP UP Lens Film Insert Diffuser (0.76) Typ .030 (5.98) Sq .235 (7.5) Sq .295 (0.76) Typ .030 (5.7) Sq .224 (4.17) Sq .164 (0.6) R .024