HA-5101_03 INTERSIL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

Features

Applications

  • High Quality Audio Preamplifiers
  • High Q Active Filters
  • Low Noise Function Generators
  • Low Distortion Oscillators
  • Low Noise Comparators
  • For Further Design Ideas, See Application Note AN554 HA-5101(SOIC) TOP VIEW BAL -IN +IN OUT

8 COMP

(BRAND) TEMP. RANGE (oC) PACKAGE PKG. NO. HA9P5101-9 (H51019) -40 to 85 8 Ld SOIC M8.15 Data Sheet May 2003 FN2905.5 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2003. All Rights Reserved All other trademarks mentioned are the property of their respective owners. OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HA-2525, HA-2842

+IN R17A Q17 R58 Q8 Q18 Q48 Q51 Q42 Q13 R18 BAL BAL R15 Q50Q49 R4B R4A Q34 -IN HA-5101

Absolute Maximum Ratings Thermal Information Operating Conditions Temperature Range Thermal Resistance (Typical, Note 2) θJA (oC/W) θJC (oC/W) (Lead Tips Only) CAUTION: Stresses above those listed in “Abs olute Maximum Ratings” may cause permanent dam age to the device. This is a stress o nly rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Maximum power dissipation, including output load, must be designed to maintain the maximum junction temperature below 150oC for the plastic packages. 2. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications VSUPPLY = ±15V, RS = 100Ω, RL = 2kΩ, CL = 50pF, Unless Otherwise Specified PARAMETER TEST CONDITIONS TEMP ( oC) MIN TYP MAX UNITS INPUT CHARACTERISTICS Offset Voltage 25 - 0.5 3 mV Full - - 4 mV Offset Voltage Drift Full - 3 - µV/ oC Bias Current 25 - 100 200 nA Full - - 325 nA Offset Current 25 - 30 75 nA Full - - 125 nA Input Resistance 25 - 500 - k Ω Common Mode Range Full ±12 - - V TRANSFER CHARACTERISTICS Large Signal Voltage Gain V OUT = ±10V 25 - 1000 - kV/V Full 100 250 - kV/V Common Mode Rejection Ratio V CM = ±10V Full 80 100 - dB Small Signal Bandwidth A V = 1 25 - 10 - MHz Minimum Stable Gain Full 1 - - V/V OUTPUT CHARACTERISTICS Output Voltage Swing R L = 10kΩ Full ±12 ±13 - V RL = 2kΩ Full ±12 ±13 - V VS = ±18V, RL = 600Ω 25 ±15 - - V Output Current (Note 3) 25 25 30 - mA Full Power Bandwidth (Note 4) 25 95 160 - kHz Output Resistance 25 - 110 - Ω Maximum Load Capacitance 25 - 800 - pF TRANSIENT RESPONSE (Note 5) Rise Time 25 - 50 100 ns Overshoot 25 - 20 35 % HA-5101

  1. Output current is measured with V OUT = ±15V with VSUPPLY = ±18V.
  2. Full power bandwidth is guaranteed by equation: .
  3. Refer to Test Circuits section of the data sheet.
  4. Settling time is measured to 0.01% of final value for a 10V output step, and A
  5. The limits for these parameters are guaranteed based on lab characterization, and reflect lot-to-lot variation.

FIGURE 1. LARGE SIGNAL R ESPONSE CIRCUIT FIGURE 2. SMAL L SIGNAL RESPONSE CIRCUIT

25% overdrive in about 6.5µs (see photos). Bottom: Output, 5V/Div., 2µs/Div. Output is overdriven negative and recovers in 6µs. FIGURE 6. NOISE SPECTRUM FIGURE 7. OFFSET VOLTAG E vs TEMPERATURE

All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that da ta sheets are current before placing orders. Information furnishe d by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com Die Characteristics SUBSTRATE POTENTIAL (Powered Up): V- TRANSISTOR COUNT: 54 PROCESS: Bipolar Dielectric Isolation Metallization Mask Layout HA-5101 BAL NC -IN +IN OUT BALV- HA-5101