GTL-OS-70100

GTL-OS-70099 GILWAY | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

Product Information Bulletin e Distributed by | www.gilway.com DRAGONtape® 781.935-4442 ; Technical Lamp/ Fax:781.928.5867 * 6 Golden DRAGON” LEDs in series connection with a one inch spacing * Self-adhesive backing for easy, reliable assembly * Intended for use with constant current power supplies for optimal efficiency © Circuit board can be cut to reconfigure LEDs; connection made by soldering wires * Size of entire module —- 6 LEDs (LxW): 5.9 in x 1.0 in (150 mm x 25 mm) * Size of smallest subunit - one LED (LxW): 1.0 in x 1.0 in (25 mm x 25 mm) * Better efficacy than incandescent or tungsten halogen * Comparable illumination to many fluorescent lamp fixtures * New longer service life when installed with proper thermal management * No ultraviolet or infrared radiation OSRAM's new DRAGONtape brings LED lighting to alevel Product Availability 7 ie 72 DRAGONtape/OS/DT6/W2-865 6500 K The DRAGONtape, like our standard LED modules, is 72 DRAGONtape/OS/OTENW2-854 5400 K available in many colors but the emphasis is on white for 72 DRAGONtape/OS/DTE/W2-847 4700 K illumination applications. DRAGONtape uses the new OSRAM 4g DRAGONtape/OS/DTE/A1 617 nm Golden DRAGON LED that delivers efficacy and service life 48 DRAGONtape/OS/DTE/Y1 587 nm far in excess of incandescent lamps, offering cost savings for 7.2 DRAGONtape/OS/DT6N1 505 nm energy and replacement labor. With a forward emitting 72 ‘DRAGONtape/OS/DT6/B1 465 nm luminous flux comparable to that of many fluorescent lamp fixtures, DRAGONtape may be specified for fluorescent specialty applications such as task lighting, backlit displays and refrigerated display cases. The DRAGONtape consists of six LEDs on a lightweight circuit board that can be used whole or subdivided. A self-adhesive backing allows the tape to be mounted on a substrate of suitable thermal conductivity to transfer heat away from the LEDs. The module operates on special constant current power supplies, available in AC-DC format for standard lighting applications and DC-DC format for specialty applications that already employ DC power, such as solar powered batteries and certain transportation vehicles.

Application Information

Applications. Power Supply Information Task lighting — reading lights, under cabinet lighting The DRAGONtape is presently compatible with the Accent lighting — cove lighting, outdoor/landscape lighting OT9/100-120/350 (NAED 51525) and the OT9/10-24/350 Refrigerated and freezer display case lighting DIM E (NAED 51526) power supply products. Contact your Light box, backlit graphies, edge lighting OSRAM SYLVANIA representative for specific information Vehicle cabin lighting - RV, truck, boat, airplane on these products and possible updates to this list. Solar powered installations SEE THE WORLD IN A NEW LIGHT OSRAM

Product Information Bulletin e Distributed by | www.gilway.com DRAGONtape® , rei 935-4042 Technical Lamp / Fax:781.938.5867 Application Information (continued) Application Notes 1. Module is intended for use with 350 mA constant current drive condition as is provided by the OT9/100-120/350 and OT9/10-24/350 DIM E (see PIB ECS0652 for details). The module is not intended for use with constant voltage power supplies, including other OSRAM LED power supplies. 2. For the white, blue and verde DRAGONtape products, the OT9 power supplies can power up to six LEDs (.¢. one complete module). For the yellow and red DRAGONtape products, the OT9 can power up to 9 LEDs (.¢. 1.5 modules). 3. Installation of the DRAGONtape must include provision for thermal management to avoid premature failure of the product and to obtain expected service life. Service life (Ie. lumen depreciation) is primarily a function of LED temperature which is to be monitored on the circuit board at the designated “To-Point". (A Tc-Point temperature of 40°C should be sufficient to enable a service life of 50,000 hours for the white DRAGONtape.) 4. There is no exact installation prescription to obtaining an appropriate Tc-Point temperature because every fixture design is different. In general, the DRAGONtape module should be adhered to a clean, flat metal surface which has enough surface area to transfer the heat from the LED to the surrounding air. The metal surface can be part of a conventional finned heat sink or can be part of the mass of the fixture itself. A very “ballpark” starting point can be interpreted from the chart below which shows approximate heat sink surface area requirements. for given service life expectations for individual DRAGON LEDs (i.e multiply area values by six for an entire DRAGONtape module). 5, Concerning fixture design, it is Important to understand that once heat Is transferred to a “heat sink”, that heat must still be allowed to escape the “system”. A heat sink transferring the thermal energy to the inside of an enclosed cavity may ultimately be of little use. 6. The fixture makers’ strategy should be to design a prototype fixture and test that fixture in an appropriate ambient environment while monitoring the temperature at the To-Point which should be allowed enough time to reach thermal equilibrium. In the end, the heat sink areas from the chart below only represent a starting point for initial design work while the Tc-Point temperature serves as the emperical test of proper thermal management. Te-Point temperature can be measured with a standard thermocouple in direct contact with the circuit board at the Te-Point or by use of ML4C Series non-reversible OMEGALABELS (www.omega.com) or equivalent. Approximate Heat Sink Size to Reach Lifetime Targets per LED (Vertically oriented flat aluminum plate: total cooling surface area equals 2x footprint area) = 8 £5 —#— White/Blue/Verde fog % 61.) 77 Yellow/Amber-red G sw 5 es 4 c § 3 8 1 Meee ee KR eK rs 0 10,000 20,000 30,000 40,000 50,000 Service Life to 50% Initial Light Intensity (hours)

Product Information Bulletin e Distributed by | www.gilway.com DRAGONtape® , 781.935-4442 Technical Lamp / Fax:781.938.5867 Safety Information 1. The LED module and all of its components must not be subject to mechanical stress. 2. Assembly must not damage or destroy the conducting paths on the circuit board. 3. The LED Module incorporates no protection against short circuits, overload or overheating. Therefore, it is absolutely necessary to operate the modules with an electrically stabilized power supply offering protection against the above mentioned safety risks. For dimming applications, attention should be paid to the specific references in the “OPTOTRONIC Technical Guide”. OSRAM OPTOTRONIC power supplies are specifically designed with protection features for safe operation. Use of third party power supplies is not recommended. 4. Installation of the LED Modules and OSRAM LED power supplies need to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations. 5. Correct electrical polarity needs to be observed. Incorrect polarity may destroy the module. 6, All LEDs, up to the maximum number allowable for the power supply, should be installed in a single electrical series connection. Electrical parallel connection can result in unbalanced voltage distribution resulting in damaging and potentially hazardous overload of some LEDs. 7. Pay attention to standard ESD precautions when handling and installing the module. 8. Only install according to the heat sinking parameters outlined in the Application Notes section, 9. Modules may be hot to touch; use caution. Assembly Information 1. Solder connections should only be performed on designated solder pads at the locations of LED subunit marked “+" and *-*. During soldering, do not exceed the maximum soldering time of 10 seconds and the maximum soldering temperature of 260°C. 2. The mounting of the module is facilitated by means of the double-sided adhesive on the back surface of the module. Care must be taken to provide a clean and dry mounting surface, free of oils or silicone coatings as well as dirt particles. The mounting substrate must have Sufficient structural integrity. Take care to completely remove the adhesive backing. Once the module is appropriately positioned, press ‘on the module with about 20 N/om* (refer to application techniques of 3M adhesives transfer tapes). 3. The module should be installed onto flat surfaces to facilitate intimate thermal contact between the circuit board and the substrate material. The module should not be installed onto curved surfaces. Minimum and Maximum Ratings For DRAGONtape (all colors) Parameter Rating Maximum Allowable Current (dc) 350 mA Maximum Reverse Voltage ov Notes: 1. Exosading maximum ratings may damage the LED module and cause potential safety hazards. 2. Elevated operating temperatures can be expected to negatively impact the service life in terms of lumen output. 3. Incomact wiring (Le. reverse polarity) with constant current power supplies may damage the LED module, 4. Not intended for use with constant voltage power supplies, Ordering and Specification Information Product Number Ordering Abbreviation Color LED Color No. of LED's Radiance angle Operating current*

70106 DRAGONtape/OS/DT6/W2 - 847 White 4700K 6 120° 350 mA

70099 DRAGONtape/OS/DT6/W2 - 854 White 5400K 6 120° 350 mA

70100 DRAGONtape/OS/DT6/W2 - 865 White 6500K 6 120° 350 mA

70101 DRAGONtape/OS/DT6/A1 Amber red 617 nm 6 120° 350 mA

70117 DRAGONtape/OS/DTE/Y1 Yellow 587 nm 6 120° 350 mA

70118 DRAGONtape/OS/DT6/V1 Verde 505 nm 6 120° 350 mA

70119 DRAGONtape/OS/DTEVB1 Blue 465 nm 6 120° 350 mA

*Please contact OSRAM SYLVANIA for details.

Product Information Bulletin e Distributed by | WY. www.gilway.com DRAGONtape® I 781.935-4442 Technical Lamp/ Fax:781.938.5867 Lamp Dimensions J 2 —| 7 + am + Sm + am 4 Boma + om + Sm 25 : ow 7 . te “e oe Ordering Guide DRAGONtape Opto Semiconductor 1D number Color code- Color Temperature W2-865= White, 6500 K ‘W2-854= White, 5400 K W2-847= White, 4700 K Al= Red Yi Yellow Vi= Verde Bi= Blue OSRAM SYLVANIA In Canada National Customer OSRAM SYLVANIA LTD. Servios and Salas Center Headquarters 18725 N. Union Street 2001 Draw Road Westfiokd, IN 46074 Mississauga, ON LES 184 Industrial & Commercial —_—‘Industrial & Commercial hone: 1- Phone: 1-800-263-2852 fee oc ous Fax: 1-800-667-6772 National Accounts Special Markets Phone: 4-800: Phone: 1-900-285-2852 Foe” 1-500-862-4674 Fax: 1-800-667-6772 OEM/Specialty Markets Phone: 1-800-762-7191 Fax: 1-800-762-7102 Display/Optic ha ew Hf DRAGONtape and OPTOTRONIC are registered trademarks of OSRAM GmbH used under license. we OSRAM js a registered trademark of OSRAM GmbH. Golden DRAGON is a trademark of OSRAM GmbH used under license,