Datasheet search site | www.alldatasheet.com
Document overview
- PDF pages: 20
Technical content
Datasheet sections
- 1 General Description
- 1.1 Scope
- 1.2 Construction
- 1.3 Outline
- 1.4 Block Diagram
- 2 General Purpose I/O Port
- 3 Electrical Specifications
- 3.1 Absolute Maximum Ratings
- 3.2 Electrical Ratings
- 3.3 Electrical Characteristics
- 4 Environmental Specifications
- 5 Optical Specifications (at 25ºC)
- 6 Physical Specifications
- 7 Applicable Specifications
- 8 Interface Details
- 8.1 USB Interface (CN3)
- 8.1.1 USB Interface – Summary
- 8.1.2 USB Interface – Technical Details
- 8.2 Serial Interface (CN9)
- 8.2.1 UART Mode (J5 = SHORT, J6 = SHORT)
- 8.2.2 SPI Mode (J5 = OPEN, J6 = OPEN)
- 8.2.3 I2C Mode (J5 = SHORT, J6 = OPEN)
- 8.3 Transmit data interface
- 8.4 Reset
- 9 Touch Panel
- 9.1 Outline
- 9.2 Basic Operation
- 9.3 Coordinates Correction (calibration)
- 9.3.1 Correction Procedure
- 9.4 Warnings
- 10 Setup
- 10.1 Jumper
- 11 Connectors
- 11.1 Serial Interface & Power through-holes (CN9)
- 11.2 General Purpose I/O Port through-holes & Power through-holes (CN11)
- 11.3 Extension General Purpose I/O Port through-holes & Power through-holes (CN10)
- 11.4 USB Interface (CN3)
- 11.5 Power through-holes (CN8)
- 11.6 Connector Position
- 12 Physical Dimensions
(Metallised Projective Capacitive Touch) Hardware Specification Model: GT800X480A-C903PA Specification No: DS-2007-0001-00 Date of Issue: June 27, 2017 (00) Revision: Published by NORITAKE ITRON Corp. / Japan http://www.noritake-itron.jp This specification is subject to change without prior notice. This product complies with RoHS Directive Please contact our sales consultant for details and to confirm the current status RoHS Compliant
GT800X480A-C903PA Hardware Specification - 3 -
1 General Description
1.1 Scope
This specification covers the hardware aspects of the GT800X480A-C903PA TFT-LCD graphic display module with a projected-capacitive touch panel.
1.2 Construction
The module consists of a 800 × 480 × RGB color graphic TFT-LCD with touch panel, refresh RAM, character generator, DC/DC converter, Microcontroller, and all necessary control logic. The module can simultaneously display graphic patterns, images, and text characters on the screen.
1.3 Outline
Display: 800×480 pixels, 65K colors (16-bit color (RGB 5-5-5 + 1bit Intensity)) Power supply: Single 5 VDC Serial interface (UART / I2C / SPI CMOS 3.3V) USB interface (High-speed / Full-speed) I/O port: 26 bits General-purpose I/O port Function: Character display Graphic display Control command Display action command Window function General-purpose I/O port control Macro, Program Macro function Character and Image download function Memory SW, Data storage Touch panel input Related specifications: DS-2007-0003-xx: “General Function” Software Specification. DS-1940-0005-xx: “Program Macro” Software Specification.
1.4 Block Diagram
Note: FROM re-write rating is approximately 100,000 times. Controller FROM1 (32Mbit) Firmware Bitmap Fonts Memory SW TFT-LCD Jumpers GPIO through-holes DC/DC Converter Backlight 3.3V GND VCC USB interface Serial Interfaces Display Controller FROM2 Stored images Outline Fonts RAM Video Memory Touch panel
GT800X480A-C903PA Hardware Specification - 4 -
2 General Purpose I/O Port
Refer to 3.3 Electrical Characteristics, “General Purpose I/O Port Voltage”. For controlling, refer to “General Function” Software Specification, “I/O Port Input / Output Setting”, “I/O Port Output”, and “I/O Port Input”.
3 Electrical Specifications
3.1 Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Note Power Supply Voltage VCC −0.3 - +6.0 VDC Logic Voltage Parameter Symbol Min. Typ. Max. Unit Note UART RXD, DSR VsIN1 -0.3 - 3.6 VDC I2C I/F SCL, SDA,*RESET VsIN2 -0.3 - 3.6 VDC SPI SCK, MOSI, SSEL, *RESET VsIN3 -0.3 - 3.6 VDC I/O Port Voltage Parameter Symbol Min. Typ. Max. Unit Note I/O port Port 0, Port 1 Port 2, Port3 ViIN −0.3 - 3.6 VDC
3.2 Electrical Ratings
Parameter Symbol Min. Typ. Max. Unit Note Output current(+3.3V) IOUT - - 20 mA Power supply voltage VCC 4.75 5.0 5.25 VDC All driving voltage for the TFT-LCD is generated from the on-board DC/DC converter. Controller 47Ω 47Ω 47Ω GPIO25 GPIO0 General-purpose I/O Port Input/Output port ×26 3.3V +3.3V 3.3V GND GND 47Ω GT800X480A-C903PA Pullup Resistor Typ. 53KΩ
GT800X480A-C903PA Hardware Specification - 5 -
3.3 Electrical Characteristics
Logic Input/Output Condition Measuring Conditions: Ambient temperature = 25 ºC, VCC=5.0VDC Parameter Symbol Min. Typ. Max. Unit Condition Note UART Logic input voltage RXD, DSR, *Reset VsIH1 2.7 - 3.5 VDC - - VsIL1 0 - 0.6 VDC - - Logic output voltage TXD, DTR VsOH1 2.8 - - VDC RL=3kΩ - VsOL1 0 - 0.4 VDC - I2C I/F Logic input voltage SCL, SDA, *RESET VsIH2 2.7 - 3.5 VDC - - VsIL2 0 - 0.6 VDC - - Logic output voltage TRDY, SBUSY VsOH2 2.8 - - VDC - - VsOL2 0 - 0.4 VDC - - Internal pull-up resistance SDA,SCL Rp 10 kΩ - - SPI Logic input voltage SCK, MOSI, *RESET,SSEL VsIH3 2.7 - 3.5 VDC - - VsIL3 0 - 0.6 VDC - - Logic output voltage TRDY, SBUSY, MISO VsOH3 2.8 - - VDC - - VsOL3 0 0.4 - - General Purpose I/O Port Voltage Measuring Conditions: Ambient temperature = 25 ºC, VCC=5.0VDC Parameter Symbol Min. Typ. Max. Unit Condition Note General-purpose I/O port Logic input current Port 0,1,2,3 IiIH - - 1.0 μADC - - IiIL - - −200 μADC - - Logic input voltage Port 0,1,2,3 ViIH 2.4 - 3.3 VDC - - ViIL 0 - 0.8 VDC - - Logic output voltage Port 0,1,2,3 ViOH 2.8 - - VDC IOH=−200μA - ViOL - - 0.4 VDC IOL=1.6mA - General Purpose I/O Port Output Permissible Current Measuring Conditions: Ambient temperature = 25 ºC, VCC=5.0VDC Parameter Symbol Min. Typ. Max. Unit Condition Note General-purpose I/O port Output permissible current Port 0,1,2,3 (Single port) IiOHp 0 - -5 mADC - - IiOLp 0 - 5 mADC - - Output permissible current Port 0,1,2,3 (Sum of all port) IiOHt 0 - -80 mADC IiOLt 0 - 80 mADC Output current should exceed the above values. If driving LEDs or other devices directly, insert current limiter into the output line. Power Supply Condition Measuring Conditions: Ambient temperature = 25 ºC, VCC=5.0VDC Parameter Symbol Min. Typ. Max. Unit Condition Note Power Supply current ICC-1 - 720 940 mADC Display power ON 100% Brightness - ICC-2 - 460 600 mADC Display power ON 50% Brightness ICC-3 - 230 300 mADC Display power OFF - Power Consumption - 3.6 4.7 W Display power ON 100% Brightness - - 2.3 3.0 W Display power ON 50% Brightness Note: The rise time of supply voltage should not exceed 100ms. Inrush current at power-on may exceed twice normal current. Display power OFF: Refer to “General Function” Software Specification, “Display power ON/OFF” command.
GT800X480A-C903PA Hardware Specification - 6 -
4 Environmental Specifications
Operating temperature: −20 to +70 ºC Storage temperature: −30 to +80 ºC Operating humidity: 20 to 80 % R.H (Non-condensing) (Temp. ≤ +60 ºC) 45 % R.H (Non-condensing) (Temp. > +60 ºC) Storage humidity: 20 to 80 % R.H (Non-condensing) (Temp. ≤ +60 ºC) 45 % R.H (Non-condensing) (Temp. > +60 ºC) Vibration (non-operating): 10-55-10Hz, all amplitude 1mm, 30 minutes, X-Y-Z Shock (non-operating): 392m/s2 (40G) 9ms X-Y-Z, 3 times each direction
5 Optical Specifications (at 25ºC)
LCD Type: TFT, Negative, Transmission Brightness TFT with touch panel: Min. 250 cd/ m2 (nit) Typ. 425 cd/ m2 (nit) 50% Brightness Min. 500 cd/ m2 (nit) Typ. 850 cd/ m2 (nit) 100% Brightness (White screen at the center of display) Color: RGB View Direction: 12 o’clock Gray Scale Inversion Direction: 6 o’clock
6 Physical Specifications
Number of pixels: 800 × RGB × 480 Display area: 154.08mm × 85.92mm (X × Y) Pixel pitch: 0.1926mm × 0.179mm (X × Y) Weight: Approximately 267g
7 Applicable Specifications
Applicable reliability specification: TT-99-3102x Applicable production specification: TT-98-3413x -20 -10 100 Brightness (%) Operating Temp (ºC)
GT800X480A-C903PA Hardware Specification - 7 -
8 Interface Details
USB, UART, I2C, and SPI serial interfaces are included on this module. The module will accept data from any configured interface. Response data is generally transmitted via the USB interface if it is active or via the configured serial interface otherwise (refer to 8.3 Transmit data interface).
8.1 USB Interface (CN3)
8.1.1 USB Interface – Summary
The USB interface is USB 2.0 High-speed (480Mbps) / Full-speed (12 Mbps) capable. Typically, the supplied USB driver is used, and the display module is accessed via a “Virtual COM port” (refer to USB VCOM Driver Installation Manual DS-1972-0000-xx). The display module can also be used as a WinUSB device, using the standard WinUSB driver. Alternatively, refer to USB Interface – Technical Details (below) if using the USB interface with a custom driver or embedded system, etc. Refer to the USB 2.0 Specification for further details.
8.1.2 USB Interface – Technical Details
The device has a single configuration, with a single interface, supporting two endpoints for data transfer: Endpoint Type Maximum packet size Endpoint 0 Control 64 bytes Endpoint 1 Bulk IN Full speed: 64 bytes, High speed: 512 bytes Endpoint 2 Bulk OUT Full speed: 64 bytes, High speed: 512 bytes Vendor ID: 0EDA (hex) Product ID: 1200 (hex) Device Class and Interface Class: FF (hex) (vendor-specific) USB Serial Number: Firmware F1.00 onwards: Unique serial number Prior firmware: Not supported WinUSB compatibility: Firmware versions F1.00 onwards support Microsoft OS String Descriptor s, which enable automatic recognition of WinUSB compatibility for applicable operating systems (manual configuration, using an .inf file, is also possible). The Device Interface GUID reported by the device is {6120D798-D192-4463-B0DE-2B65ED2F4870}. This GUID is used by applications on the host in order to access the device.
GT800X480A-C903PA Hardware Specification - 8 -
8.2 Serial Interface (CN9)
One of three modes is selected by Jumpers J5 and J6. For all modes, the SBUSY/ DTR signal reflects the state of the receive buffer. This can be used for flow control if necessary. Data received is stored in the internal receive buffer, and processed in order of receipt. The TRDY signal indicates whether or not there is data currently held in the transmit buffer. Buffer Capacity Receive buffer 2,047 bytes Transmit buffer 127 bytes SBUSY / DTR Signal Change Timing SBUSY change ‘L’(READY)→‘H’(BUSY) ‘H’(BUSY) →‘L’(READY) Receive buffer space 62 bytes or less 128 bytes or more TRDY signal change timing TRDY READY(‘H’) EMPTY(‘L’) Condition Data in transmit buffer No data in transmit buffer
8.2.1 UART Mode (J5 = SHORT, J6 = SHORT)
Interface Conditions: Baud rate 4800 to 115200bps (set by Jumper and Memory SW) Default setting: 38400bps Parity None, Even, Odd (set by Memory SW) Default setting: None Format Start (1 bit) + Data (8 bit) + Parity (0 or 1 bit) + Stop (1 bit) Communication control signal DSR, DTR, /TRDY ・ Data transmitted from the display is placed in the internal transmit buffer and sent, in order, when DSR = READY . DTR RXD Min. 0μs ‘H’ ‘L’ DSR TXD Min. 0μs Max. 2 bytes ‘H’ ‘L’ BUSY (‘H’) READY (‘L’) BUSY (‘H’) READY (‘L’) Max. 24 bytes
GT800X480A-C903PA Hardware Specification - 9 -
8.2.2 SPI Mode (J5 = OPEN, J6 = OPEN)
Display module operates as an SPI slave; data is sent and received in response to host (master) operations. SSEL= 1 0 1 is one command sequence. 1st BYTE Operation Mode 44h Data Write (Host → Module) 54h Data Read (Host ← Module) 58h Status Read (Host ← Module) Data Write When 44h is input as the first byte, the module receives the 2nd and subsequent bytes as data. 1st BYTE 2nd BYTE 3rd BYTE --- n BYTE MOSI 44h Data(1) Data(2) --- Data(n-1) MISO - - - --- - Data Read When 54h is input as the first byte, the module outputs valid data on the 3rd and subsequent bytes. The host must read the number of bytes reported by the immediately preceding Status Read command. The number of bytes reported by the Status read command will be transmitted, with any unread bytes discarded. 1st BYTE 2nd BYTE 3rd BYTE --- n BYTE MOSI 54h - - --- - MISO - 00h Data(1) --- Data(n-2) Status Read When 58h is input as the first byte, the module outputs status data. For the 3rd and any subsequent bytes, the most recent status data is provided. 1st BYTE 2nd BYTE --- n BYTE MOSI 58h - --- - MISO - Status Status Status Status bit assignment b7 b6 b5 b4 b3 b2 b1 b0 SBUSY 0* TL(b5) TL(b4) TL(b3) TL(b2) TL(b1) TL(b0) SBUSY : SBUSY signal TL : Number of Transmit data bytes available (maximum 63 bytes) *: If b6 is 1, the Status byte is invalid. SPI Timing tDly: Data write Min. 120ns Data Read/Status Read Min. 40µs SSEL MOSI SCK MISO Min.120ns Min. 60ns Min. 30ns Min. 100ns Min. 20ns tDly Min. 60ns Min. 100ns Max. 30ns
GT800X480A-C903PA Hardware Specification - 10 -
8.2.3 I2C Mode (J5 = SHORT, J6 = OPEN)
Slave address is set by Jumpers J0 and J1. J0 J1 Function OPEN OPEN I2C Slave Address = 50h SHORT OPEN I2C Slave Address = 51h OPEN SHORT I2C Slave Address = 52h SHORT SHORT I2C Slave Address = 53h Note: Module does not respond to the General call address (00h). Communication Parameters Baud rate Max. 400kbps Format I2C Slave address Set by J0 and J1 (Default setting: 50h) Supported functions ACK response, Clock stretch Communication control signals SBUSY , TRDY *Note: If clock stretch is applied during processing of a command, the host (master) will not be able to send or receive any more data until command processing has finished. If TRDY = EMPTY, FFh is transmitted from the module in response to a read sequence. In addition to the Clock stretch function, flow can also be controlled by monitoring the MBUSY signal. MBUSY signal changes according to the receive buffer state. The host should send data when MBUSY=READY (refer to 8.2 Serial Interface (CN9)). Data write sequence S (Sr) SLAVE ADDRESS R/*W ACK DATA ACK ･･･ DATA ACK P Data read sequence S (Sr) SLAVE ADDRESS R/*W ACK DATA ACK ･･･ DATA NACK P Host (master) is transmitter, display module (slave) is receiver Host (master) is receiver, display module (slave) is transmitter
GT800X480A-C903PA Hardware Specification - 11 - I2C Timing Parameter Symbol Condition Min. Typ. Max. Unit SCL clock frequency fSCL - 0 - 400 kHz Start condition hold time tHD;STA - 0.6 - - µs SCL ‘L’ time tLOW - 1.3 - - µs SCL ‘H’ time tHIGH - 0.6 - - µs Start condition setup time tSU;STA - 0.6 - - µs Data hold time tHD;DAT - 0 - - µs Data setup time tSU;DAT - 100 - - ns SCL, SDA rise time tr - 20 - 300 ns SCL, SDA fall time tf - - 300 ns Stop condition setup time tSU;STO - 0.6 - - µs Stop condition – start condition bus idle time tBUF - 20 - - µs Data Write Sequence Data Read Sequence SDA SCL Slave Address + Write(0) DATA SBUSY Max. 20μs Min. 0μs DATA A C K A C K A C K SDA SCL Slave Address + Read(1) DATA TRDY Max. 20μs Min. 0μs DATA A C K A C K (N) A C K
GT800X480A-C903PA Hardware Specification - 12 -
8.3 Transmit data interface
If the USB interface is used in addition to a Serial interface, confusion can arise over which interface data transmitted from the display module is sent via. Initially, the configured Serial interface is selected for transmit data. If the USB interface is active and a USB read is attempted by the host (ie, a USB bulk-IN transaction is directed at the device’s Endpoint 1), the USB interface is selected for transmit data. However, if data is s ubsequently received on the configured Serial port, the configured Serial port is then used instead, from that point onwards, for all transmit data (regardless of USB activity). This state continues until an external reset, power cycle, or “User setup mode end” command.
8.4 Reset
Display module can be reset by inputting a LO signal to *RESET (connector CN9, pin 1). Note that, while *RESET is held LO, and for up to 200ms after *RESET release (including initial power-on time), pin 2 of connector CN9 (I 2C signal SCL / SPI signal SCK) is held LO. To avoid overcurrent due to signal contention, ensure that any line connected to this pin is not driven HI during this time. SCL / SCK Max. 200ms *RESET hi-Z LO LO HI
GT800X480A-C903PA Hardware Specification - 13 -
9 Touch Panel
9.1 Outline
Detection method: MPCT (Metallised Projective Capacitive Touch) supporting multi-touch.
9.2 Basic Operation
The display module features a touch panel for handling input by fingertip or touch pen, etc. The touch panel function sends data for the input position or operation of user-defined switch buttons. Refer to “General Function” Software Specification for details. Transmit buffer (2) (Data format depends on control mode) Data transmit (USB, UART I2C, etc) Calculation (Input position, switch information) Touch action (1) (Contact by fingertip, touch pen, etc) Touch sensed Program Macro buffer (3) (If Program Macro running)
GT800X480A-C903PA Hardware Specification - 14 -
9.3 Coordinates Correction (calibration)
The display module includes a touch position correction function, for minimizing any inconsistency between the actual touch position and the internally-calculated position information. The correction function requires a touch on a single-dot position 5 times with a small finger point. Note: The display module is shipped from the factory in a correctly-adjusted state.
9.3.1 Correction Procedure
- Short jumper J10 and power ON. The screen shown on the right is displayed. (For jumper details, refer to 10.1 Jumper.） 2. Touch the center of the upper left cross 5 times. 3. Touch the center of the bottom-right cross 5 times. 4. To commit the calculated calibration values, press and hold “YES”. To discard the values, press “NO”. 5. The module will restart. Confirm touch operation with J10 open. Touch position Position information: (6, 3) Touch position Position information: (4, 1) Correction Top left Top left TOUCH POSITION CALLIBRATION 1. ( , ) ( , ) 2. ( , ) ( , ) 3. ( , ) ( , ) 4. ( , ) ( , ) 5. ( , ) ( , ) AVG. ( , ) ( , ) --- Callibration values --- LEFT RIGHT UPPER LOWER OLD: 0 0 0 0 NEW: TOUCH POSITION CALLIBRATION 1. (65, 83) ( , ) 2. (61,100) ( , ) 3. (58, 71) ( , ) 4. (72,100) ( , ) 5. (78,100) ( , ) --- Callibration values --- LEFT RIGHT UPPER LOWER OLD: 0 0 0 0 NEW: TOUCH POSITION CALLIBRATION --- Callibration values --- LEFT RIGHT UPPER LOWER OLD: 0 0 0 0 NEW: TOUCH POSITION CALLIBRATION --- Callibration values --- LEFT RIGHT UPPER LOWER OLD: 0 0 0 0 NEW: 7 36 -13 5 NO YES Commit?
GT800X480A-C903PA Hardware Specification - 15 -
9.4 Warnings
Because this touch panel is capacitive type, touch won’t work if a conductive material is placed on the touch area or bezel area. We recommend the use of non-conductive material like an acrylic panel. An example is shown below. When installing, be careful not to pinch the backlight power cable near the lower left corner, or the FPC cables on the lower edge (refer to 12 Physical Dimensions).
10 Setup
10.1 Jumper
J5 Serial Interface (CN9) mode Open J6 Open J7 Macro Start Open J8 Reserved Open J9 Reserved Open J10 Touch panel calibration mode Open Open = “H”, Short = “L” Refer to Software Specification for Jumper setting details. Bezel area Bezel area Active touch area Acryl panel Touch panel Air gap Unit TFT LCD Reverse side (opposite TFT-LCD panel) Jumper J10
GT800X480A-C903PA Hardware Specification - 16 -
11 Connectors
11.1 Serial Interface & Power through-holes (CN9)
No. Signal name Function Direction UART SPI I2C 1 *RESET *RESET *RESET Reset Input 2 - SCK SCL Serial Clock Input
3 RxD MOSI SDA Data Receive Input/ Output
4 DTR SBUSY SBUSY Display Busy Output
5 DSR SSEL - Host Busy Input
6 TXD MISO - Data Send Output
7 TRDY TRDY TRDY Target Ready Output
8 VCC VCC VCC Power Supply (5V) -
9 GND GND GND Ground -
11.2 General Purpose I/O Port through-holes & Power through-holes (CN11)
No. Signal name Function Direction Pin No. Signal name Function Direction 1 VCC Power supply (5V) Input 2 3.3V 3.3V Output
3 GPIO 15
4 GPIO 14
5 GPIO 13 6 GPIO 12
7 GPIO 11 8 GPIO 10
9 GPIO 9 10 GPIO 8
11 GPIO 7
12 GPIO 6
Port 0 13 GPIO 5 14 GPIO 4
15 GPIO 3 16 GPIO 2
17 GPIO 1 18 GPIO 0
19 GND Ground Input 20 GND Ground Input
11.3 Extension General Purpose I/O Port through-holes & Power through-holes (CN10)
No. Signal name Function Direction Pin No. Signal name Function Direction 1 VCC Power supply (5V) Input 2 3.3V 3.3V Output
3 GPIO 25 Port 3
4 GPIO 24 Port 3
5 GPIO 23
6 GPIO 22
Port 2 7 GPIO 21 8 GPIO 20
9 GPIO 19 10 GPIO 18
11 GPIO 17 12 GPIO 16
13 GND Ground Input 14 GND Ground Input
11.4 USB Interface (CN3)
Pin No. Signal name
1 VBUS
5 GND
11.5 Power through-holes (CN8)
Pin No. Signal name Function
1 Vcc Power Supply (5V)
2 NC(*TEST) No Connection (Factory test use only)
3 GND Ground
- Factory use only (leave this pin open)
GT800X480A-C903PA Hardware Specification - 17 -
11.6 Connector Position
Serial Interface & Power through-holes
GT800X480A-C903PA Hardware Specification - 18 -
12 Physical Dimensions
Mounting holes are close to the panel; use caution when assembling. DS-2007 -0101-00
GT800X480A-C903PA Hardware Specification - 19 - Notice for the Cautious Handling of LCD Modules Handling and Usage Precautions: Please carefully follow the appropriate product application notes and operation standards for proper usage, safe handling, an d maximum performance. [LCD panel is made of glass] Use caution to avoid breaking the LCD glass envelope, to prevent injury from sharp glass particles. Please design the PCB for the LCD module within 0.3 mm warping tolerance to avoid any forces that may dam age the display due to PCB distortion causing a breakdown of the electrical circuit leading to LCD failure. [Cable Connection] Do not unplug the power and/or data cables of LCD modules during operation, because unrecoverable damage may result. Sending input signals to the LCD module when it isnot powered can cause I/O port damage. It is recommended to use a 30cm or shorter signal cable to prevent functional failures. [Electrostatic Charge] LCD modules need electrostatic-free packaging and protection from electrostatic charges during handling and usage. [Structure] During operation, LCD and LCD modules generate heat. Please consider sufficient heat radiation dissipation using heat sink solutions. Preferably, use UL-grade materials or components in conjunction with LCD modules. Warp and twist movement causes stress and may break LCDs and LCD modules. Please adhere to allowances within 0.3mm at the point of attachment. [Power] Apply regulated power to the LCD module within specified voltages to protect from failures. LCD modules may draw in-rush current exceeding twice the typical current at power-on, so a power supply with sufficient capacity and quick starting of the power regulator is recommended. LCD module needs a specified voltage at the point of connec tion. Please use an adequate power cable to avoid a decrease in voltage. As a safety measure, a fuse or other over-current protection is recommended. [Operating Consideration] A signal cable 30cm or less is recommended to avoid possible disturbances to the signal. [Storage and Operating Environment] Please use LCD modules under the recommended specified environmental conditions. Salty, sulfuric and dusty environments may damage the LCD module even during storage. [Disposal] LCD uses lead-containing materials (RoHS directive exempts these lead compounds in the glass for electronic devices). When discarding LCDs or LCD modules, please adhere to applicable laws and regulations. [Other Cautions] Although the LCD module is designed to be protected from electrical noise, please plan your circuitry to exclude as much noise as possible. Do not reconstruct or repair the LCD module without our authorization. We cannot assure the quality or reliability of unauthorized reconstructed LCD modules. Notice: We do not authorize the use of any patents that may be inherent in these specifications. Neither whole nor partial copying of these specifications is permitted without our approval. If necessary, please ask for assistance from our sales consultant. This product is not designed for military, aerospace, medical or other life-critical applications. If you choose to use this product for these applications, please ask us for prior consultation or we cannot accept responsibility for problems that may occur.
GT800X480A-C903PA Hardware Specification - 20 -
Revision history
Specification number Date Revision DS-2007-0000-00 Jun. 27, 2017 Initial issue