GM5510 GAMMA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 12

Technical content

Features

Highly accurate: ± 2% Low power consumption: TYP 0.7µA [V = 1.5V]IN Detect voltage range: 1.6V to 6.0V in 0.1V increments Operating voltage range: 0.7 to 10.0V Detect voltage temperature characteristic: TYP ± 100 ppm/ °C Output Configuration: CMOS or N channel open drain TYPICAL APPLICATION CIRCUITS GM5510 V0.1 www.gammamicro.com 1 VIN VOUT VSS 100kW R GM5510N VINVIN VIN VOUT VSS GM5510C CMOS Output N-ch Open Drain Output Application Computers Controllers Intelligent Instruments Critical µP and uC Power Monitoring Portable/ Battery- Powered Equipment Automotive

MARKING INFORMATION & PIN CONFIGURATIONS (TOP VIEW) GM5510 T = Output Config. (C = CMOS, N = N ch. Open Drain) V V = Detect Voltage (27=2.7V, 30 = 3.0V) A = Assembly Location Y = Year WW = Weekly XX = Device Code ( GA= GM5510N, GB= GM5510C) V = Detect Voltage (Refer to "Voltage Suffix") Y = Year WW = Weekly VSS VIN VOUT 1 2 * For detail Ordering Number identification, please see last page. SOT-343 (SSOT-24) XXV VSS VINVOUT 1 2 4 3 NC

ORDERING INFORMATION

Ordering Number Package Shipping GM5510C-1.8ST23R GM5510C-1.8ST34R GM5510C-1.8ST89R GM5510C-3.0ST23R GM5510C-3.3ST34R GM5510C-3.0ST89R GM5510C-4.0ST23R GM5510C-4.0ST34R GM5510C-4.0ST89R GM5510C-4.2ST23R GM5510C-4.2ST34R GM5510C-4.2ST89R SOT-23 SOT-23 SOT-23 SOT-23 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel GM5510C-2.7ST23R GM5510C-2.0ST23R GM5510C-2.7ST34R GM5510C-2.7ST89R GM5510C-2.0ST34R GM5510C-2.0ST89R GM5510C-3.6ST23R GM5510C-3.6ST34R GM5510C-3.6ST89R GM5510C-4.1ST23R GM5510C-4.1ST34R GM5510C-4.1ST89R SOT-343 SOT-89 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel Output Config. Detect Voltage Voltage Suffix: V CMOS CMOS CMOS 1.8V 1.8V 1.8V C CMOS CMOS CMOS CMOS CMOS CMOS 2.7V 2.0V 2.7V 2.7V 2.0V 2.0V K E CMOS CMOS CMOS 3.0V 3.3V 3.0V N CMOS CMOS CMOS 3.6V 3.6V 3.6V T CMOS CMOS CMOS 4.0V 4.0V 4.0V X CMOS CMOS CMOS 4.1V 4.1V 4.1V Y CMOS CMOS CMOS 4.2V 4.2V 4.2V Z 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel SOT-23 SOT-23 SOT-23 SOT-23 SOT-343 SOT-89 SOT-343 SOT-89 SOT-343 SOT-89 SOT-343 SOT-89 SOT-343 SOT-89 SOT-343 SOT-89 SOT-343 SOT-89 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel GM5510C-2.9ST34R GM5510C-2.9ST89R CMOS CMOS 2.9V 2.9V SOT-343 SOT-89 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel GM5510C-2.9ST23R CMOS 2.9V M 3,000 Units/ Tape & ReelSOT-23 C K E Q T X Y Z M GM5510C-3.3ST89R 1,000 Units/ Tape & ReelCMOS 3.3V SOT-89 GM5510C-3.0ST34R 3,000 Units/ Tape & ReelCMOS 3.0V SOT-343N GM5510C-3.3ST23R CMOS 3.3V Q 3,000 Units/ Tape & ReelSOT-23

Ordering Number Package Shipping GM5510N-1.8ST23R GM5510 -1.8ST34RN GM5510 -1.8ST89RN GM5510 -3.0ST23RN GM5510 -3.3ST34RN GM5510 -3.0ST89RN GM5510 -4.0ST23RN GM5510 -4.0ST34RN GM5510 -4.0ST89RN GM5510 -4.2ST23RN GM5510 -4.2ST34RN GM5510 -4.2ST89RN SOT-23 SOT-23 SOT-23 SOT-23 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel GM5510 -2.7ST23RN GM5510 -2.0ST23RN GM5510 -2.7ST34RN GM5510 -2.7ST89RN GM5510 -2.0ST34RN GM5510 -2.0ST89RN GM5510 -3.6ST23RN GM5510 -3.6ST34RN GM5510 -3.6ST89RN GM5510 -4.1ST23RN GM5510 -4.1ST34RN GM5510 -4.1ST89RN SOT-343 SOT-89 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel Output Config. Detect Voltage Voltage Suffix: V 1.8V 1.8V 1.8V C 2.7V 2.0V 2.7V 2.7V 2.0V 2.0V K E 3.0V 3.3V 3.0V N 3.6V 3.6V 3.6V T 4.0V 4.0V 4.0V X 4.1V 4.1V 4.1V Y 4.2V 4.2V 4.2V Z 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel SOT-23 SOT-23 SOT-23 SOT-23 SOT-343 SOT-89 SOT-343 SOT-89 SOT-343 SOT-89 SOT-343 SOT-89 SOT-343 SOT-89 SOT-343 SOT-89 SOT-343 SOT-89 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel GM5510 -2.9ST34RN GM5510 -2.9ST89RN 2.9V 2.9V SOT-343 SOT-89 3,000 Units/ Tape & Reel 1,000 Units/ Tape & Reel GM5510 -2.9ST23RN 2.9V M 3,000 Units/ Tape & ReelSOT-23 C K E Q T X Y Z M GM5510 -3.3ST89RN 1,000 Units/ Tape & Reel3.3V SOT-89 GM5510 -3.0ST34RN 3,000 Units/ Tape & Reel3.0V SOT-343N GM5510 -3.3ST23RN 3.3V Q 3,000 Units/ Tape & ReelSOT-23 GM5510 N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain PARAMETER SYMBOL RATINGS UNIT Input Voltage V IN 12 V Output Current IOUT 50 mA Output Voltage CMOS Nch open drain Operating Ambient Temperature Topr -40 to + 85 °C Storage Temperature Tstg -40 to +125 V - 0.3 to V + 0.3SS IN V - 0.3 to 12SS V ABSOLUTE MAXIMUM RATINGS (T = 25°C)A Power Dissipation SOT-23 SOT-89 P D VOUT 150 500 mW N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain N-ch Open Drain

(1) CMOS Output (2) Nch Open Drain Output BLOCK DIAGRAM PARAMETER CONDITIONS MIN TYP MAX UNIT CIRCUIT SYMBOL Detect Voltage Hysteresis Range Supply Current Operating Voltage Output Current Temperature Characteristics Delay Time (V "V inversion)DR OUT VDF VHYS ISS VIN IOUT tDLY V = 1.5VIN V = 2.0VIN V = 3.0VIN V = 4.0VIN V = 5.0VIN V (T) = 1.6V to 6.0VDF Nch V = 0.5VDS V = 1.0VIN V = 2.0VIN V = 3.0VIN V = 4.0VIN V = 5.0VIN Pch V = 2.1VDS V = 8.0VIN (with CMOS output) -40°C Topr 85°C V X 0.98DF V X 0.02DF 0.7 1.0 3.0 5.0 6.0 7.0 V DF V X 0.05DF 0.7 0.8 0.9 1.0 1.1 2.2 7.7 10.1 11.5 13.0 -10.0 ± 100 V X 1.02DF V X 0.08DF 2.3 2.7 3.0 3.2 3.6 10.0 -2.0 0.2 V 1 µA 2 ppm/ °C - mA mS 5 DVDF DTopr -VDF V 1 V 1 Note: V (T): Established Detect Voltage ValueDF Release Voltage: V = V DR HYSV +DF ELECTRICAL CHARACTERISTICS [V (T) = 1.6 to 6.0V ± 2%]DF GM5510 T = 25°C A

INPUT VOLTAGE (V )IN DETECT RELEASE VOLTAGE (V )DR DETECT VOLTAGE (V )DF MIN. OPERATING VOLTAGE (V )MIN GROUND VOLTAGE(V )DF OUTPUT VOLTAGE (V )OUT GROUND VOLTAGE(V )SS Function Description (CMOS output) When input voltage (V ) rises above detect voltage (V ), output voltage (V ) will be equal to V .IN DF OUT IN (A condition of high impedance exists with Nch open drain output configurations.) When input voltage (V ) falls below detect voltage (V ), output voltage (V ) will be equal to the ground voltage IN DF OUT (V ) level.SS When input voltage (V )falls to a level below that of the minimum operating voltage (V ), output will become unstable.IN MIN In this condition, V will equal to the pulled-up output (should output be pulled-up).IN When input voltage (V ) rises above the ground voltage (V ) level, output will be unstable at levels below the minimum IN SS operating voltage (V ). Between the V and detect release voltage (V ) levels, the ground voltage (V )level willMIN MIN DR SS be maintained. When input voltage (V ) rises above detect release voltage (V ), output voltage (V ) will be equal to V .IN DR OUT IN (A condition of high impedance exists with Nch open drain output configurations). The difference between V and V represents the hysteresis range.DR DF 1 2 3 4 5

V VIN VOUT VSS 100kW (Note 1)R VIN VIN A VIN VOUT VSS Circuit 1 Circuit 2 VIN VDS A VIN VOUT VSS VIN A VIN VOUT VSS VDS Circuit 3 Circuit 4 VIN VOUT VSS 100kW (Note 1)R Circuit 5 Note 1: Not necessary with CMOS output products. Measurement waveform

  1. When a resistor is connected between the V pin and the input with CMOS output configurations, oscillation may IN occur as a result of voltage drops at R if load current (I ) exists. IN OUT 2. When a resistor is connected between the V pin and the input with CMOS output configurations, irrespective of IN Nch output configurations, oscillation may occur as a result of through current at the time of voltage release even if load current (I ) does not exist.OUT 3. With a resistor connected between the V pin and the input, detect and release voltage will rise as a result of the IN IC's supply current flowing through the V pin.IN 4. In order to stabilise the IC's operations, please ensure that V pin's input frequency's rise and fall times are more IN than several µ sec/ V. (Refer to N.B 1- (1) below) (Refer to N.B 1- (2) below) N. B. 1. Oscillation (1) Output current oscillation with the CMOS output configuration When the voltage applied at IN rises, release operations commence and the detector's output voltage increases. Load current (I ) will flow at R . Because a voltage drop (R x I ) is produced at the R resistor, located OUT L IN OUT IN between the input (I ) and the V pin, the load current will flow via the IC's V pin. The voltage drop will also N IN IN lead to a fall in the voltage level at the V pin. When the V pin voltage level falls below the detect voltage level, IN IN detect operations will commence. Following detect operations, load current flow will cease and since voltage drop at R will disappear, the voltage level at the V pin will rise and release operations will begin over again.IN IN Oscillation may occur with this "release" repetition. Further, this condition will also appear via means of a similar mechanism during detect operations. (2) Oscillation as a result of through current Since the GM5510 series are CMOS IC's, through current will flow when the IC's internal circuit switching operates (during release and detect operations). Consequently, oscillation is liable to occur as a result of drops in voltage at the through current's resistor (R ) during release voltage operations. (Refer to diagram2)IN Since hysteresis exists during detect operations, oscillation is unlikely to occur. GM5510C VIN RIN IOUT Input R X I IN OUT Voltage drop VSS VOUT GM5510N GM5510C VIN RIN Input R X I * IN SS Voltage drop VSS VOUT I *SS (Includes through current) GM5510N VIN VSS VOUT C RIN Diagram: Circuit using an input resistor

TYPICAL PERFORMANCE CHARACTERISTICS (1) Supply Current vs. Input voltage 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 2 4 6 8 10 Input Voltage: V (V)IN Supply Current: I (µA)SS GM5510C-18(1.8V) 25°C -40°C T = 85°CA 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 2 4 6 8 10 Input Voltage: V (V)IN Supply Current: I (µA)SS GM5510C-27(2.7V) T = 85°CA 25°C -40°C 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 2 4 6 8 10 Input Voltage: V (V)IN Supply Current: I (µA)SS GM5510C-36(3.6V) T = 85°CA 25°C -40°C (2) Detect, Release Voltage vs. Ambient Temperature 1.90 1.85 1.80 1.75 -50 -25 0 25 50 75 100 VDR VDR Ambient Temp.: T (°C)A Detect, Release Voltage: V , V (V)DF DR 2.80 2.75 2.70 2.65 -50 -25 0 25 50 75 100 VDR VDR Ambient Temp.: T (°C)A Detect, Release Voltage: V , V (V)DF DR 3.8 3.7 3.6 3.5 -50 -25 0 25 50 75 100 VDR VDR Ambient Temp.: T (°C)A Detect, Release Voltage: V , V (V)DF DR (3) Output Voltage vs. Input Voltage (4) N-ch Driver Output current vs. VDS T = 25°CA 00 1 2 Output Voltage: V (V)OUT Input Voltage: V (V)IN 0 1 2 3 Output Voltage: V (V)OUT T = 25°CA Input Voltage: V (V)IN 0 1 2 3 4 Output Voltage: V (V)OUT Input Voltage: V (V)IN T = 25°CA T = 25°CA 00 0.5 1.0 1.5 2.0 Output Current: I (mA)OUT V (V)DS V = 1.5VIN 1.0V T = 25°CA V = 2.5VIN 2.0V 1.5V 1.0V Output Current: I (mA)OUT V (V)DS V (V)DS Output Current: I (mA)OUT T = 25°CA V = 3.0VIN 2.5V 2.0V 1.5V GM5510C-18(1.8V) GM5510C-27(2.7V) GM5510C-36(3.6V) GM5510C-18(1.8V) GM5510C-27(2.7V) GM5510C-36(3.6V) GM5510C-18(1.8V) GM5510C-27(2.7V) GM5510C-36(3.6V)

TYPICAL PERFORMANCE CHARACTERISTICS GM5510 T = 25°CA 1000 800 600 400 200 Output Current: I (µA)OUT V (V)DS (4) N-ch Driver Output current vs. VDS V = 0.8VIN 0.7V T = 25°CA 1000 800 600 400 200 Output Current: I (µA)OUT V (V)DS V = 0.8VIN 0.7V T = 25°CA 1000 800 600 400 200 Output Current: I (µA)OUT V (V)DS V = 0.8VIN 0.7V GM5510C-18(1.8V) GM5510C-27(2.7V) GM5510C-36(3.6V) (6) N-ch DRIVER OUTPUT CURRENT VS. INPUT VOLTAGE 0 0.5 1.0 1.5 2.0 Input Voltage: V (V)IN 25°C -85°C V = 0.5VIN Input Voltage: V (V)IN 25°C 0 1 2 3 4 Input Voltage: V (V)IN T = 40°CA Output Current: I (mA)OUT Output Current: I (mA)OUT Output Current: I (mA)OUT V = 0.5VDS T = 40°CA -85°C T = 40°CA V = 0.5VDS 25°C -85°C GM5510C-18(1.8V) GM5510C-27(2.7V) GM5510C-36(3.6V) (7) P-ch DRIVER OUTPUT CURRENT VS. INPUT VOLTAGE 0 2 4 6 8 10 Output Current: I (mA)OUT Input Voltage: V (V)IN Output Current: I (mA)OUT Input Voltage: V (V)IN Input Voltage: V (V)IN Output Current: I (mA)OUT V = 2.1VDS 1.5V 1.0V 0.5V 0 2 4 6 8 10 V = 2.1VDS 1.5V 1.0V 0.5V 0 2 4 6 8 10 V = 2.1VDS 1.5V 1.0V 0.5V GM5510C-18(1.8V) GM5510C-27(2.7V) GM5510C-36(3.6V)

SOT-89 PACKAGE OUTLINE DIMENSIONS Pad Layout 45° 1.5 1.5 0.7 4.50 ± 0.05 Units: mm1.650 REF

1.400 REF

4.20 ± 0.05 1.00 ± 0.07 2.5 ± 0.05 0.46 ± 0.025 3.00 ± 0.025 1.50 1.50 1.50 ± 0.05 0.38 ± 0.01 R 0.13~3X NO DRAFT~2 R 0.1 MAX 6°~2X 6°~2X R 0.13~2X R 0.13~2X Unit: mm R 0.13~4X SOT-23 PACKAGE OUTLINE DIMENSIONS 2.90 ± 0.1 0.4 ± 0.1 1.5 ± 0.05 0.95 ± 0.038 2.8 ± 0.1 1.9 ± 0.05 Unit: mm 0.65 ± 0.05 1.10 ± 0.1 0.13 0~0.1 0.8 ± 0.05 0.079 2.0 0.031 0.8 Inches mm( ) 0.035 0.9 0.037 0.95 0.037 0.95 Pad Layout

GM 5510 / 5510 C N 1.8 ST23 R Gamma Micro. Circuit Type Package ST23: SOT-23 ST89: SOT-89 ST34: SOT-343 Shipping R: Tape & Reel Output Voltage 4.2: 4.2V CMOS N-ch Open Drain SOT-343 (SSOT-24) PACKAGE OUTLINE DIMENSIONS 2.10 ± 0.10 0.65BSC Unit: mm 0.90 ± 0.10 1.30 ± 0.10 2.3 + 0.10 - 0.30 4 - 0.25 ± 0.10 4° ± 4° 0.10 + 0.05 - 0.02 R0.10 REF R0.08 REF 0.36 ± 0.10 0.20 1.10MAX 0.05 ± 0.05 0.55 ± 0.05 1.25 ± 0.10