DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Series G Fully Illuminated Ultra-Miniature Toggles www.nkk.comA38 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable RockersTouch Tilt AToggles General Specifications Electrical Capacity (Resistive Load) Logic Level: 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Other Ratings Contact Resistance: 80 milliohms maximum Insulation Resistance: 500 megohms minimum @ 500V DC Dielectric Strength: 500V AC minimum for 1 minute minimum Mechanical Life: 100,000 operations minimum Electrical Life: 100,000 operations minimum 10,000 operations minimum @ 0.1A @ 28V AC/DC Nominal Operating Force: 1.30N Angle of Throw: 28° Materials & Finishes Actuator: Polyamide Case: Glass fiber reinforced polyamide Sealing Rings: Nitrile butadiene rubber Movable Contacts: Phosphor bronze with gold plating Stationary Contacts: Phosphor bronze with gold plating Base: Glass fiber reinforced polyamide Power Terminals: Phosphor bronze with gold plating Lamp Terminals: Phosphor bronze with gold plating Environmental Data Operating Temperature Range: –25°C through +55°C (–13°F through +131°F) Humidity: 90 ~ 95% humidity for 240 hours @ 40°C (104°F) Vibration: 10 ~ 500Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) PCB Processing Soldering: Wave Soldering recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Cleaning: Automated cleaning. See Cleaning specifications in Supplement section. Standards & Certifications The G Series toggles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy.
Series GFully Illuminated Ultra-Miniature Toggles www.nkk.com A39 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable A TogglesRockersTouch Tilt Distinctive Characteristics Actual Size Fully illuminated toggle for highly visible status indication with LED in red, green, or amber for single color and red/green for bicolor. Ultra-miniature size allows high density mounting, and extremely light weight makes these switches ideal for handheld equipment. Totally sealed body construction prevents contact contamination and allows time- and money-saving automated soldering and cleaning. Molded-in, epoxy sealed terminals lock out flux, solvents, and other contaminants. Award-winning STC contact mechanism with benefits unavailable in conventional mech- anisms: smooth, positive detent actuation, increased contact stability, and unparalleled logic-level reliability. (Additional STC details in Terms & Acronyms; see Supplement section.) .100” x .100” (2.54mm x 2.54mm) terminal spacing conforms to standard PC board grid spacing. Round terminals facilitate easier through- hole mounting on PC boards.
Series G Fully Illuminated Ultra-Miniature Toggles www.nkk.comA40 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable RockersTouch Tilt AToggles Pole
1 SPDT
TYPICAL SWITCH ORDERING EXAMPLE Circuits
2 ON NONE ON
Combines with single color or bicolor LEDs
3 ON OFF ON
C LEDS Single Color C Red D Amber F Green ON-NONE-ON only Bicolor CF Red/Green ON-NONE-ON & ON-OFF-ON 28° (1.7) Dia .067 (4.0) Dia .157 (3.8) .150 Clear Toggle, Red LED Right Angle PC Terminals SPDT ON-NONE-ON Circuit Toggle Position Connected Terminals Schematics Pole Throw Model Up Center Down Up Center Down SPDT G12 G13 ON ON NONE OFF ON ON 2-3 2-3 NONE OPEN 2-1 2-1 POLES & CIRCUITS Slot Slot Note: Terminal numbers are not actually on the switch. LED circuit is isolated and requires an external power source. Single Color Bicolor (5) (6) (5) (4) Red (6) Green LED COLORS & SPECIFICATIONS LEDs are an integral part of the switch and not available separately. The electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement; see Supplement Index. Single Color Bicolor Red Amber Green Red/Green Forward Peak Current I FM 25mA 25mA 25mA 25mA/25mA Continuous Forward Current IF 20mA 20mA 20mA 20mA/20mA Reverse Peak Voltage VRM 4V 4V 4V 4V/4V Current Reduction Rate Above 25°C ∆IF 0.33mA/°C Ambient Temperature Range –25° ~ +55°C D FC CF Colors 2 (COM)
Series GFully Illuminated Ultra-Miniature Toggles www.nkk.com A41 IndicatorsAccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable A TogglesRockersTouch Tilt PC TERMINALS P H VStraight Right Angle TYPICAL SWITCH DIMENSIONS Straight PC Right Angle PC 5 & 6 are LED terminals; 4 is a support pin on single color models & an LED terminal on bicolor models. G12JPC 5 & 6 are LED terminals; 4 is a support pin on single color models & an LED terminal on bicolor models. G12JHD Vertical PC 5 & 6 are LED terminals; 4 is a support pin on single color models & an LED terminal on bicolor models. G12JVCF Vertical (2.54) Typ .100 (2.6) .102 (2.54) Typ .100 (0.4) Dia Typ .016 (7.0) .276 (4.5) .177 (0.4) Dia Typ .016 (2.54) Typ .100 (7.0) .276 (4.5) .177 (2.54) Typ .100 (0.5) Typ .020 (4.5) .177 (7.0) .276 (0.5) Typ .020 (2.54) Typ .100 (2.54) Typ .100 (0.4) Dia Typ .016 Slot (4.5) .177 28° (1.7) Dia .067 (4.0) Dia .157 (0.4) Dia Typ .016 (3.8) .150 (2.6) .102 (7.0) .276 (1.6) .063 (2.54) Typ .100 (7.0) .276 (2.54) .100 (0.6) Dia Typ .024 (2.54) Typ .100 (2.54) .100 1 (0.6) Dia Typ .024 (2.54) Typ .100 (2.54) .100 12 3 45 6 (5.08) .200 (0.6) Dia Typ .024 (5.08) .200 (2.54) Typ .100 (2.54) .100 1 Slot (5.08) .200 (7.8) .307 (0.4) Dia Typ .016 (1.7) Dia .067 (4.0) Dia .157 (2.6) .102 (0.5) .020 (2.54) .100 (5.08) .200 (1.6) .063 (10.22) .402 (3.8) .150 28° 32 1 4 5 6 (0.4) .016 (4.9) .193 (0.4) Dia Typ .016 (7.0) .276 (2.54) Typ .100 (5.3) .209 (2.54) .100 (0.4) Dia Typ .016 Slot (2.6) .102 (0.5) Typ .020 (2.54) Typ .100 (1.6) .063 (3.8) .150 (1.0) .039 (5.08) .200 (12.76) .502 28° (1.7) Dia .067 (4.0) Dia .157 (7.4) .292 (2.54) .100 (4.5) .177 (0.4) Dia Typ .016 (0.4) .016