FXU-HC52 FOX | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 11
Technical content
Features
Frequency Resolution to six decimal places Stabilities to ± 20 PPM -20 to +70°C or -40 to +85°C operating temperatures Tri-State Enable / Disable Feature Industry Standard Package, Footprint & Pin-Out Fully RoHS compliant Gold over Nickel Termination Finish Serial ID with Comprehensive Traceability Note * – Higher frequencies are available. Contact Fox Technical Support for details.
PRELIMINARY SPECIFICATIONS FXU-HC52 Series Page 4 of 11 © 2014 FOX ELECTRONICS | ISO9001:2008 Certified An Integrated Device Technology, Inc. company Output Wave Characteristics Parameters Symbol Condition Maximum Value (unless otherwise noted) Low Output Voltage VOL 0.016 MHz to 167 MHz 10%VDD High Output Voltage VOH 0.016 MHz to 167 MHz 90%VDD Minimum Output Symmetry @ 50% VDD Level (See Drawing Below) 0.016 to 62.5 MHz 62.5+ to 167 MHz 45% ~ 55% 40% ~ 60% Output Enable (PIN # 1) Voltage VIH ≥ 70% VDD Output Disable (PIN # 1) Voltage VIL ≤ 30% VDD Cycle Rise Time (10%~90%VDD - See Drawing Below) TR 0.016 to 167 MHz 2.0 nS Typical Cycle Fall Time (90%~10%VDD - See Drawing Below) TF 0.016 to 167 MHz 1.0 nS Typical 20% to 80% 10% to 90% 0V to V Rise Time Fall Time Times 80 - 20 50% V On Time Off Time 1/2 Period Period Ideally, Symmetry should be 50/50 -- Other expressions are 45/55 or 55/45 1/2 Period Rise Time / Fall Time Measurements Oscillator Symmetry 70 - 30 Times 30% to 70% DD DD
PRELIMINARY SPECIFICATIONS FXU-HC52 Series Page 5 of 11 © 2014 FOX ELECTRONICS | ISO9001:2008 Certified An Integrated Device Technology, Inc. company Phase Jitter is integrated from Agilent 5052A Signal Noise Analyzer; measured directly into 50 ohm input; VDD =2.5V. HCMOS Phase Jitter (typical measurement at 125 MHz) Frequency Phase Jitter (pS) 125 MHz 0.36 (per SONET OC-48: 12kHz to 20 MHz) Phase Noise (typical measurements at 125 MHz)
PRELIMINARY SPECIFICATIONS FXU-HC52 Series Page 6 of 11 © 2014 FOX ELECTRONICS | ISO9001:2008 Certified An Integrated Device Technology, Inc. company NOTE: XPRESSO-Ultra HCMOS XOs are designed to fit on Industry Standard, 4 pad layouts Pin Description and Recommended Circuit Pin # Name Type Function
1 E / D 1 Input Enable / Disable Control of Output (0 = Disabled)
2 GND Ground Electrical Ground for VDD
3 Output Output HCMOS Oscillator Output
4 VDD 2 Power Power Supply Source Voltage
N. C. Hi Z No Connection (Factory Use ONLY) NOTES: 1 Includes pull-up resistor to VDD to provide output when the pin (1) is No Connect. 2 Installation should include a 0.01µF bypass capacitor placed between V DD (Pin 4) and GND (Pin 2) to minimize power supply line noise. E / D VDD N. C. N. C. GND Output Terminations as viewed from the Top Enable / Disable Control Pin # 1 (state) Output (Pin #3) OPEN (No Connection) ACTIVE Output “1” Level VIH ≥ 70% VDD ACTIVE Output “0” Level VIL ≤ 30% VDD High Impedance Soldering Reflow Profile (2 times Maximum at 260°C for 10 seconds MAX) 25°C 160°C 180°C 225°C 260°C
10 Seconds Max
within 5°C of 260°C peak Ramp Down Not to exceed 6°C/s Ramp-Up 3°C/s Max pt 120 ± 20 Seconds In Pre-heating Area Above 225°C Reflow Area 50±10 Seconds
400 Seconds MAX from +25°C to 260°C peak
PRELIMINARY SPECIFICATIONS FXU-HC52 Series Page 7 of 11 © 2014 FOX ELECTRONICS | ISO9001:2008 Certified An Integrated Device Technology, Inc. company Mechanical Dimensional Drawing & Pad Layout Actual part marking is depicted. See Traceability (pg. 9) for more information Drawing is for reference to critical specifications defined by size measurements. Certain non-critical visual attributes, such as side castellations, reference pin shape, etc. may vary NOTE: XPRESSO-ULTRA HCMOS XOs are designed to fit on Industry Standard, 4 pad layouts Pin Connections #1) E/D #3) Output #2) GND #4) V DD *TP are test points and are NC.
PRELIMINARY SPECIFICATIONS FXU-HC52 Series Page 8 of 11 © 2014 FOX ELECTRONICS | ISO9001:2008 Certified An Integrated Device Technology, Inc. company An additional identification code is contained internally if tracking should ever be necessary Tape and Reel Dimensions Labeling (Reels and smaller packaging are labeled with the below) Fox Part Number: 851A-125-3 Quantity: 2000 pieces LOT # 24435 If traceability should become necessary Description: FXU-HC525R-125 Date Code 1335 (YYWW 2013 35 th wk) 851A-125-3 Ø1.5mm4.0mm 8.0mm 7.5mm 16mm 2.15mm 2.0 255.0 17.5 80.0 2.0 Ø13.0 Ø21.0 120° Ø21.0Ø13.0 17.5 2.0 178.0 62.0 2.0 2.0 2k Reel Dimensions 1k Reel Dimensions in mm in mm 12mm 5.5mm 1335 FXU-HC525R-125-5
PRELIMINARY SPECIFICATIONS FXU-HC52 Series Page 9 of 11 © 2014 FOX ELECTRONICS | ISO9001:2008 Certified An Integrated Device Technology, Inc. company LOT Number The LOT Number has direct ties to the customer purchase order. The LOT Number is marked on the “Reel” label, and also stored internally on non-volatile memory inside the X PRESSO-ULTRA part. XPRESSO-ULTRA parts that are shipped Tape and Reel, are also placed in an Electro Static Discharge (ESD) bag and will have the LOT Number labeled on the exterior of the ESD bag. It is recommended that the X PRESSO-ULTRA parts remain in this ESD bag during storage for protection and identification. If the parts become separated from the label showing the LOT Number, it can be retrieved from inside one of the parts, and the information that can be obtained is listed below: Customer Purchase Order Number Internal Fox Sales Order Number Dates that the X PRESSO-ULTRA part was shipped from the factory The assigned customer part number The specification that the part was designed for Serial Identification The Serial ID is the individualized information about the configuration of that particular X PRESSO-ULTRA part. The Serial ID is unique for each and every XPRESSO-ULTRA part, and can be read by special Fox equipment. With the Serial ID, the below information can be obtained about that individual, X PRESSO-ULTRA part: Equipment that the X PRESSO-ULTRA part was configured on Raw material used to configure the X PRESSO-ULTRA part Traceability of the raw material back to the foundries manufacturing lot Date and Time that the part was configured Any optimized electrical parameters based on customer specifications Electrical testing of the actual completed part Human resource that was monitoring the configuration of the part Fox has equipment placed at key Fox locations World Wide to read the Lot Identification and Serial Number of any X PRESSO-ULTRA part produced and can then obtain the information from above within 24 hours Traceability – LOT Number & Serial Identification
PRELIMINARY SPECIFICATIONS FXU-HC52 Series Page 10 of 11 © 2014 FOX ELECTRONICS | ISO9001:2008 Certified An Integrated Device Technology, Inc. company Mechanical Testing Parameter Test Method Mechanical Shock MIL-STD-202 Method 213 Condition C Mechanical Vibration MIL-STD-202 Method 204 5g's for 20 minutes 12 cycles of each 3 orientations: X, Y, Z High Temperature Operating Life (HTOL) Under Power @ 125°C for 1000 Hours Hermetic Seal He pressure: 4 ±1 kgf / cm2 2 Hour soak
PRELIMINARY SPECIFICATIONS FXU-HC52 Series Page 11 of 11 © 2014 FOX ELECTRONICS | ISO9001:2008 Certified An Integrated Device Technology, Inc. company XpressO-ULTRA Home XpressO-ULTRA XOs XpressO Brochure Patent Numbers: US 6,664,860, US 5,960,403, US 5,952,890; US 5,960,405; US 6,188,290; China ZL 98802217.6, Malaysia MY-118540-A, Philippines 1-1998-000245, Hong Kong #HK1026079, Mexico #232179 US and Foreign Patents Pending XpressO® Fox Electronics Contact Information (USA)-Worldwide Headquarters Tel: 888-GET-2-FOX Outside US: +1.239.693.0099, Email: www.foxonline.com/email.htm Fox EMEA Tel: +44.1283.568153 Email: www.foxonline.com/email.htm Fox Japan Fax: +81.3.3377.5221 Email: www.foxonline.com/email.htm Fox Singapore Tel:+886-2-22073427, Email: www.foxonline.com/email.htm The above specifications, having been carefully prepared and checked, is believed to be accurate at the time of publication; however, no responsibility is assumed by Fox Electronics for inaccuracies.