FX15

FX15 HIROSE | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 24

Technical content

1mm Pitch Wire-to-Board Connectors supporting LVDS signal FX15 Series Contacts consolidated into 1 row for equal length transmission lines Mating side: 1 mm pitch, staggered 2-row construction Termination side: 0.5mm pitch, 1-row construction ■Features 1. Space-saving Reduction in space is achieved by designing the contacts in 2-row staggered 1mm pitch on the mating side and on a single row 0.5mm pitch on the termination side (Fig.1). 2. Equal length transmission lines Contact configuration provides equal length transmission lines, which prevents LVDS signal loss within the connector. 3. Variations Availability of shielded and non-shielded types allows for design flexibility and cost reduction. 4. Self alignment and self-guiding Built-in guide posts allow secure self-alignment within ±1.5mm (Fig.2). 5. Secure and complete mating / unmating Side latch locking provides complete and secure mating, as well as easy unmating (Fig.3). 6. Enhanced shielding performance with FX15S Enlarged metal shields prevent intrusion and emission of electromagnetic interference, which enhances the integrity of the LVDS signal (Fig.4). 7. RoHS compliant All materials and substances used to produce this product comply with RoHS standards. Space saving, Equal length transmission lines -10 -20 -30 -40 -50 Frequency (GHz) With metal Without metal Emitting Noise Level (dBm) High Shielding Performance Fig.1 Self-alignment of ±1.5mm Side latch -locks Large guide post 1.5mm1.5mm 1.5mm With metal shields (FX15 and FX15S Series) Without metal shields (FX15M Series) Fig.2 Fig.3 Fig.4 2015.10e

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal Note 1 : Includes temperature rise caused by current flow. Note 2 : The term “storage” refers to products stored for long period of time prior to mounting and use. Operating temperature and humidity range includes non-conducting condition of installed connectors in storage, shipment or during transportation. Note 3 : Includes wire conductor resistance (12mm long).

• Receptacle
• Plug ■Product Specifications ■Materials / Finish Ratings Current rating Voltage rating 0.5A 100V AC Operating temperature range Storage temperature range -55ç to +80ç (Note 1) -10ç to +60ç (Note 2) Item Specification Conditions 1. Contact resistance 60mø max. (Note 3) 1mA 2. Insulation resistance 500Mø min. 100V DC 3. Withstanding voltage No flashover or insulation breakdown. 300V AC/one minute 4. Insertion-Extraction force 2N min., 30N max. With corresponding connector 5. Mating cycles Contact resistance : 80mø max.(Note 3) 50 cycles 6. Vibration resistance No electrical discontinuity of 1µs or more. Frequency: 10 to 55 Hz, single amplitude of 0.75mm, 2 hours, 3 axis 7. Shock resistance No electrical discontinuity of 1µs or more. Acceleration of 490m/s2, 11ms durations, sine half-wave waveform, 3 cycles, 3axis. 8. Humidity resistance Contact resistance : 80mø max. No damage, cracks, or parts dislocation.(Note 3) 96 hours at 40ç, RH 90% to 95% 9. Temperature cycle Contact resistance : 80mø max. (Note 3) Insulation resistance : 500Mø min. Temperature : -55ç → +15ç to +35ç → +85ç → +15ç to +35ç Time : 30 → 5 → 30 → 5 (Minutes) 5 cycles 10. Salt spray Contact resistance : 80mø max. (Note 3) No corrosions 5% water solution for 48 hours. Component Material Finish Remarks Insulator Polyamide Color : Black UL94V-0 Contact Phosphor bronze Contact area : Gold plated Metal shell (shielded version only) FX15S : Nickel silver FX15SC : Stainless steel Component Material Finish Remarks Insulator Polyamide Color : Black UL94V-0 Contact Phosphor bronze Contact area : Gold plated Metal shell, metal latch locks qSeries Name : FX15 wConfiguration Blank : With shields (or crimp contact) 15S : With shields – enhanced shielding 15SC : With shields – enhanced shielding (PCB mounting pattern : VESA standard) 15M : Without shields eNumber of contacts rConnector type P : Male contact S : Female contact tContact pitch : 0.5 mm yHousing configuration SH : Right angle SV : Straight uTermination C : Crimp 0.5SD : Micro-coaxial cable GND : Separate ground plate iApplicable conductor 2830 : 28 to 30 AWG 3032 : 30 to 32 AWG oPackaging PCF : Male contact / reel !0Plating (contact area) B : Gold plated !1Packaging Blank : Embossed Packaging (1,000 pcs/reel) (30) : Embossed Packaging (100 pcs/reel)
• Receptacle FX15 S - 31 P - C
• Plug FX15 - 3032 PCF B
• Crimp contact ■Product Number Structure !0oiq u !1ytrewq rewq

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal ■FX15 Series – Functional Diagram Crimp contact Crimp contact (FX15-3032-PCFB) Crimp contact (FX15-2830-PCFB) Plugs Receptacles BB B Without shields (FX15M-P-C) Right angle, with shields –enhanced shielding (FX15S-S-0.5SH) With shields – enhanced shielding (FX15S-P-C) Right angle, without shields (FX15M-S-0.5SH) With shields – enhanced shielding PCB mouting pattern : VESA standard (FX15SC-S-0.5SH) With shields – enhanced shielding PCB mouting pattern : VESA standard (FX15SC-S-0.5SV) With shields – enhanced shielding 28 to 30 AWG (FX15SW-31P-C) A Micro-coaxial cable (FX15S-P-0.5SD) With shields-standard (FX15-31P-C) Vertical, with shields (FX15-31S-0.5SV) Ground plate (FX15S-P-GND)

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal 3.7±0.3 4±0.3B±0.3 (A) 9.4±0.3 D±0.3 C±0.15 (13.45) 2.7±0.1 E±0.15 P=1±0.1 P=1±0.1 F±0.15No.1 No.2 No.n No.n-1 Polarizing mark indicator ■Plugs No.2 No.1 No.30 No.31 Polarizing mark indicator 22.57±0.15 (27) 9.4±0.3 18.3±0.3 (13.45) P=1±0.1 14±0.15 P=1±0.1 15±0.15 24.6±0.3 2.7±0.1 3.7±0.3

• With shields (FX15-31P-C) Note 1 : Packaged in trays. Note 2 : Dimensions in parenthesis ( ) are reference dimensions. Part No. HRS No. No. of contacts RoHS FX15-31P-C 575-2101-2 31 Yes
• With shields, enhanced shielding (FX15S-**P-C) Note 1: Packaged in trays. Note 2 : Dimensions in parenthesis ( ) are reference dimensions. Part No. HRS No. No. of contacts A B C D E F RoHS FX15S-31P-C 575-2106-6 31 27 24.6 22.6 18.3 14 15 YesFX15S-41P-C 575-2107-9 41 32 29.6 27.6 23.3 19 20 FX15S-51P-C 575-2103-8 51 37 34.6 32.6 28.3 24 25

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal C±0.3 F±0.15 P=1±0.1 P=1±0.1 E±0.15 No.1 No.n-1No.2 No.n B±0.3 9.55±0.3 (A) (D) (13) (13.6) 4.2±0.3 Polarizing mark indicator

• Without shields (FX15M-**P-C) 4±0.324.6±0.3 (27) 9.4±0.3 18.3±0.3 3.7±0.3 22.57±0.15 (13.45) 2.7±0.1 14±0.15 P=1±0.1 P=1±0.1 15±0.15No.1 No.2 No.30 No.31 B A Polarizing mark indicator
• With shields – enhanced shielding 28 to 30 AWG (FX15SW-31P-C) Note 1 : Packaged in trays. Note 2 : Dimensions in parenthesis ( ) are reference dimensions. Part No. HRS No. No. of contacts RoHS FX15SW-31P-C 575-2113-1 31 Yes Part No. HRS No. No. of contacts A B C D E F RoHS FX15M-21P-C 575-2109-4 21 24.8 20.5 13.7 25.8 9 10 Yes FX15M-31P-C 575-2108-1 31 29.8 25.5 18.7 30.8 14 15 Note 1 : Sold in 100 piece packages. Please order in full package quantities. Note 2 : Dimensions in parenthesis ( ) are reference dimensions.

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal BPlug crimp contacts Part No. HRS No. Packaging Quantity Finish RoHS FX15-2830PCFB 575-2002-0 Reel 20,000 pcs/reel Gold plated Yes FX15-3032PCFB 575-2003-3

• Applicable cable (Tin plated, annealed copper wire) FX15-2830PCFB Applicable wire size (Stranded wire conductor) Jacket diameter UL No. 28 AWG (7/0.127mm) Ø0.56 to 0.72mm 1517 30 AWG (7/0.1mm) 1571 FX15-3032PCFB Applicable wire size (Stranded wire conductor) Jacket diameter UL No. 30 AWG (7/0.1mm) Ø0.5 to 0.6mm 1516, 1571(Note) 32 AWG (7/0.08mm) 1571
• Wire strip length: 1.1 to 1.8mm Note : When using wires other than those noted above, please contact Hirose for asistance.
• Tools Item Part No. HRS No. Applicable crimp contact Applicator AP105-FX15-2830 901-4036-0 FX15-2830PCFB AP105-FX15-3032 901-4033-1 FX15-3032PCFB 0.5±0.15 0.9±0.15 0.72±0.1 (7) 2±0.15 0.35±0.1 t=0.15±0.05

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal 8¤%#&* 9¤%#&* Cd#& Cd#c Cd#& Cd#' Cd#c Cd#c"& (#*¤%#( 7¤%#( -#,*¤%#( EdaVg^o^c\\bVg\` ^cY^XVidg

• Plug – Micro-coaxial cable (FX15S-**P-0.5SD) 6¤%#'
• Ground plate for micro-coaxial cable type Part No. HRS No. No. of contacts A B RoHS FX15S-41P-GND 575-2111-6 41 29.2 30.06 Yes FX15S-51P-GND 575-2117-2 51 34.2 35.06 Note 1 : Packaged in trays. Note 2 : Dimensions in parenthesis ( ) are reference dimensions. Part No. HRS No. No. of contacts A B C D RoHS FX15S-41P-0.5SD 575-2110-3 41 31.9 29.6 27.57 20 Yes FX15S-51P-0.5SD 575-2118-5 51 36.9 34.6 32.57 25 Note 1 : Packaged in trays. Note 2 : Dimensions in parenthesis ( ) are reference dimensions.
• Applicable cable (Micro-coaxial cable) Wire size (Standed wire inner conductor) Jacket diameter 36 AWG (7/0.05mm) 0.3mm to 0.5mm38 AWG (7/0.04mm) 40 AWG (7/0.03mm) No. of contacts A B 41 23.1 20 51 28.1 25
• Cable preparation 7¤%#&* E2%#*¤%#%, %#.B6M >chjaVidg DjiZgXdcYjXidg %#+¤%#& (+id)%6L<B^Xgd"XdVm^VaXVWaZ 6¤%#' <gdcY^c\\WVg &B>C HdaYZgXdVi ?VX\`Zi

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal No.1 No.2 No.31 No.30 a b cd ef P=0.5±0.1 15±0.15 19.82±0.2 25.7±0.3 4±0.3 5.6±0.3 (6) (0.8) 0.9±0.2 22.8±0.3 4.8±0.3 ■Receptacles

• Vertical, with shielding (FX15-31S-0.5SV) 1.5 0 -0.05 3.2+0.05 2-Ø1(TH) 2-Ø1.4(LND) 0.9 0 -0.1 4.1+0.1 17.72 0 -0.1 21.92 +0.1 2.2 0 -0.1 6.7+0.1 22.8±0.05 15±0.05 0.25±0.03(Metal mask) 0.2+0.1 Note 1 : The co-planarity of the terminal leads is as follows:
• All signals and shield leads “c” and “d”: 0.1mm max.
• Shield leads “a”, “b”, “e” and “f”: 0.15mm max. 2 : Area indicated by the crosshatched lines must be free of conductive traces or the conductive traces must be covered by resist film. 3 : Packaged on tape-and-reel. 4 : Dimensions in parenthesis ( ) are reference dimensions. BRecommended PCB mounting pattern and metal mask dimensions Part No. HRS No. No. of contacts RoHS [Specifi cation Number : , () ] Blank : Embossed packaging (1,000 pcs/reel) (30) : Embossed packaging (100 pcs/reel)

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal 4.45±0.1 (3) (0.2) (1.7) 0.5±0.1 A±0.2 P=1±0.1 P=1±0.1 C±0.15 D±0.15 B±0.2 E±0.3 0.2±0.05No.1 No.2 No.n No.n-1 (2.6) (4) Polarizing mark indicator 4.4±0.3

• Right angle with shields – enhanced shielding (FX15S-S-0.5SH) L 0 -0.05 4.25 4.15 K±0.05 0.5±0.03 0.25±0.03(Metal mask) J 0-0.05 H+0.05 0 G 0-0.05 F+0.05 0 3.55+0.05 0 2.05 0 -0.05 M +0.05 0 N23.2 0-0.05 P26.8+0.05 0 3.7+0.05 0 1.45 0 -0.052.2+0.05 0 1.7 0 -0.05 3.7+0.05 0 R 13.85 S 0.3±0.03(Land) 2 : Do not place any components in the area indicated. Placement of components in this area may affect mating and latch lock operation. 3 : Area indicated by the cross-hatched lines must be free of conductive traces or the conductive traces must be covered by resist film. 4 : The area marked indicates vacuum pick-and-place area for board placement with automatic equipment. 5 : Vacuum pick-up area 6 : Packaged on tape-and-reel. 7 : Dimensions in parenthesis ( ) are reference dimensions. BRecommended PCB mounting pattern and metal mask dimensions Part No. FX15S-31S-0.5SH() FX15S-41S-0.5SH() FX15S-51S-0.5SH() 575-2306-5 575-2307-8 575-2303-7 ** HRS No. No. of contacts A B C D 27.8 32.8 37.8 E 28.8 33.8 38.8 F 24.8 29.8 34.8 G 21.6 26.6 31.6 H 27.4 32.4 37.4 J K 5.2 L 8.8 M 13.2 18.2 23.2 N 16.8 21.8 26.8 P 24.8 29.8 34.8 R Yes S RoHS

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal 4.3±0.3 4.8±0.3 (5.5) Vacuum pick and place area Polarizing mark indicator No.1 No.2 No.n No.n-1 6.55±0.3 B±0.2 D±0.15 P=1±0.1 P=1±0.1 C±0.15 A±0.2 0.5±0.1 0.2±0.05 6.15±0.3

• Right angle, without shielding (FX15M-S-0.5SH) E±0.05 0.3±0.03(Land) 0.9±0.03 3.7 0 -0.05 7.4+0.05 (1.85) 0.25±0.03(Metal mask) G 14 2 F±0.05 P=0.5±0.03 1.9 0 -0.05 3.4+0.05 Note 1 : The co-planarity of all terminal leads is 0.1mm max. 2 : Do not place any components in the area indicated. Placement of components in this area may affect mating and latch lock operation. 3 : Packaged on tape-and-reel. BRecommended PCB mounting pattern and metal mask dimensions Part No. HRS No. No. of contacts A B C D E F G RoHS FX15M-21S-0.5SH() 575-2309-3 21 10 22.4 9 10 17.9 10 35 Yes FX15M-31S-0.5SH() 575-2308-0 31 15 27.4 14 15 22.9 15 40 [Specifi cation Number : , (**) ] Blank : Embossed packaging (1,000 pcs/reel) (30) : Embossed packaging (100 pcs/reel)

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal 0.18±0.05 1.5±0.1 3.1±0.2 4.45±0.2 0.5±0.1 F±0.3 1.5±0.1 (0.25 ) (1.1) P=1±0.1 G±0.15 H±0.15 P=1±0.1 No.1 No.n 4.4±0.3 P=0.5±0.1 C±0.2 B±0.2 E±0.2 P=D±0.1 A±0.3 Polarizing mark indicator

• Right angle with shields – enhanced shielding (FX15SC-S-0.5SH) PCB mounting pattern : VESA standard 1.55±0.05 K 5.6 3.5±0.05 5.1±0.05 J±0.05 2.05±0.05 2.5±0.05 C±0.05 B±0.05 2.5±0.05 1.55±0.05 E±0.05 No.1 No.n BRecommended PCB mounting pattern and metal mask dimensions Note 1 : The coplanarity of the terminal leads is 0.1mm max. 2 : Do not place any components in the area indicated. Placement of components in this area may affect mating and latch lock operation. 3 : Area indicated by the cross-hatched lines must be free of conductive traces or the conductive traces must be covered by resist film. 4 : Packaged on tape-and-reel. 5 : Dimensions in parenthesis ( ) are reference dimensions. Part No. HRS No. No. of contacts A B C D E F G H J K RoHS FX15SC-41S-0.5SH() 575-2310-2 41 32.85 26 20 4 20 32.4 19 20 29.75 45 Yes FX15SC-51S-0.5SH() 575-2311-5 51 37.85 31 25 5 25 37.4 24 25 34.75 50 [Specifi cation Number : , (**) ] Blank : Embossed packaging (1,000 pcs/reel) (30) : Embossed packaging (100 pcs/reel)

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal E±0.3 A±0.2 D±0.2 P=C±0.1 0.5±0.1 P=0.5±0.1 1.5±0.1 0.18±0.05 No.nB±0.2No.1 5.3±0.3 4.2±0.2 5.5±0.3

• Vertical with shields – enhanced shielding (FX15SC-S-0.5SV) PCB mounting pattern : VESA standard B±0.05 A±0.05 D±0.05 A±0.05 P=C±0.05 2.5±0.056-1.3±0.05 No.1 No.n BRecommended PCB layout and metal mask dimensions Note 1 : The coplanarity of the terminal leads is 0.1mm max. 2 : Area indicated by the cross-hatched lines must be free of conductive traces or the conductive traces must be covered by resist film. 3 : Packaged on tape-and-reel. Part No. HRS No. No. of contacts A B C D E RoHS FX15SC-41S-0.5SV() 575-2205-8 41 26 20 4 20 32.4 Yes FX15SC-51S-0.5SV() 575-2204-5 51 31 25 5 25 37.4 [Specifi cation Number : , (**) ] Blank : Embossed packaging (1,000 pcs/reel) (30) : Embossed packaging (100 pcs/reel)

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal A±0.1 B±0.1 C±0.3 Ø1.5 +0.1 0 4±0.1 12±0.1 (0.5) (4.7) (6.7) Unreeling direction A A A A A (4.8) (0.5) (6.3) Unreeling direction 40.45±0.1 44±0.3 +0.1 0 Ø1.5 +0.1 0 4±0.12±0.15 12±0.1 BPackaging Specifications

• Vertical, with shields (FX15-31S-0.5SV) Part No. HRS No. No. of contacts D
• Right angle, with shields-enhanced shielding (FX15S-**S-0.5SH) Part No. HRS No. No. of contacts ABCD 26.3 52.5 56 56.5
• Right angle, without shields (FX15M-**S-0.5SH) Part No. HRS No. No. of contacts ABCD 20.2 40.4 44 44.5 A±0.1 B±0.1 C±0.3 Ø1.5 +0.1 0 4±0.12±0.1 12±0.1 (0.5) (5.15) (6.5) Unreeling direction Ø13±0.5 (1.6) (Ø380) (Ø80) (D)
• Reel dimensions

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal A±0.1 B±0.1 C±0.3 Ø1.54±0.12±0.1 12±0.1 (0.5) (6.7) +0.10 Unreeling direction

• Right angle with shields – enhanced shielding (FX15SC-**S-0.5SH) Part No. HRS No. No. of contacts ABCD RoHS 26.2 52.4 56 56.5 Yes
• Vertical with shields – enhanced shielding (FX15SC-**S-0.5SV) Part No. HRS No. No. of contacts ABCD RoHS 26.2 52.4 56 56.5 Yes Unreeling direction (0.5) A±0.1 B±0.1 C±0.3 Ø1.5 +0.10 4±0.12±0.1 12±0.1 (7) Ø13±0.5 (1.6) (Ø380) (Ø80) (D)
• Reel dimensions

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal 250 150ç 180ç 30± 10sec.90±30sec. 230ç MAX 250ç Time (sec.) Sodering (230çmin) Preheating(150 to 180ç) 230 180 150 100 Temperature (ç) BRecommended temperature profile HRS test conditions Test board Glass epoxy 40mm∞30mm∞1mm thick Solder method : Reflow Solder composition : Paste 96.5%Sn/3%Ag/0.5%Cu Metal mask : 0.12mm thick Reflow cycles : 2 cycles The temperature profile is based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume/ thickness and board size/thickness. Consult your solder paste and equipment manufacturer for specific recommendations. Note : The temperature profile indicates the maximum temperature of the connector surfaces at the highest point from the PCB mounting surface. BWashing Conditions Water Type Washing When using water type cleaning agents (e.g., terpene, and alkali saponifiers), select the cleaning agent based on the documentation issued by the various manufacturers of cleaning agents which describes the effects on metals and resins. Be careful that parts are not left with moisture remaining on them. Washing Precautions Residual flux or cleaning agent on the contacts when washing with organic solvents or water type cleaners can give rise to the deterioration of electrical performance. In this regard it is important to check whether a thorough washing has been performed. Organic Solvent Washing Solvent type Room temperature washing Heated washing IPA (Isoporopyl alcohol) Yes Yes

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal Precautions and recommendations Retention tab Crimp side Molded-in lance Molded-in lance Molded-in lance Retention tab facing down Retention tab facing up Retention tab ◆Wire termination The following documents will be needed in order to perform the cable terminations. 1Basic cable termination and crimp requirements (general explanations). 2Contact crimp termination machine instruction manual (Explanation of the press) 3Applicator parts installation table (Applicator installation explanation) 4Crimp conditions table (Crimp height/Tensile strength standard values) 5Crimp quality fundamentals manual (Bell-mouth dimensions, bent up, bent down, rolling, etc.) * Correct cable preparation and crimp termination is based on understanding and following the procedures in the above documents. ◆Insertion of the crimp contacts in the housing Crimp contacts are inserted in the housing as illustrated below. Exercising caution when inserting, align the retention tab of the contact with the corresponding molded-in lance in the housing’s contact cavity and push the contacts in. Make sure that the contact is fully inserted and the retention tab clears the molded-in lance. ◆Verify that the retention tabs clear the molded-in lances as shown on the illustration below. Light pull on the wire, with force NOT EXCEEDING 3N will also verify the correct contact insertion. ◆Removal of the contacts Using sharp-pointed tool of appropriate size gently lift the molded-in tab and pull-out the terminated contacts. Excersize caution as NOT to damage the molded-in lance. Should the damage occur, the entire housing will need to be replaced.

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal Soldering area 1 Soldering area 2 (Ground harness examples) B B [ Soldering precautions related to FX15S-**P-C connectors ] ◆Grounding Methods of the ground wire or shields for the cable assemblies 1 Solder the ground wire or the shields ONLY in the areas specifically designated for this purpose, as shown on the illustrations below. 2Observe the soldering iron tip temperature and soldering time specified. 3Do not apply excessive force to the connector by pressing it with the tip of a soldering iron. 4Do not splatter the flux from the solder core. Precautions and recommendations

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal

2 Minimize the length of outer conductor beyond the ground the

bar. 3 Length of cutting the extra cable should be 2.1mm Max. Any longer cable may cause contact with the connector ɹɹduring assembly and could damage the product. Recommended minimum length is 2.0mm, but this can be altered as long as good soldering ability is maintained. 4Pre-solder and coat the inner conductor at the cable end. 2. Recommended solder for the assembly is flux cored solder with 0.2mm dia. (Lead-free: Sn-3Ag-0.5Cu), 21mm length. If additional flux is used, make sure to prevent wicking onto the contact area. Wicking onto the contact area will cause the contacts to fail. 3. Before soldering the cable and connector with a cable assembly machine, check the points to avoid below.

1 Misalinment of cable end to the terminals in pitch direction

2 Excessive floating of cable end

1. Follow the recommended temperature profile shown below for the soldering. The optimum conditions for soldering can vary depending on cable type and length, and solder type. Be sure to check the recommended temperate profile and adjust the conditions accordingly. ◆Plug – micro-coaxial cable Cautions for soldering 1. For the micro coaxial cable assembled to this connector, cable alignment process as shown in "Recommended cable" on the page 1 is required before assembly. Width of ground bar shall be 1.05mm Max. including misalignment of overlapping, flush by cutting, side drop or soldering. Using an inadequate cable will interfere the assembly to the connector. Forceful assembly and soldering could cause mis-soldering and damage the product. Precautions and recommendations Inner conductor Outer conductor Grounding bar q w w e rSolder coating qMisalignment in pitch direction wfloating 50ç 250ç 265ç Pre-heating Heating Idling 2s 1s 2s 3-4s 220ç Duration of pressure application Solder tip pressurization Temperature Duration Heating 265±5ç 3~4 sec 13~17N

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal [ Coutions for potting process ] 1. Protect the soldered area by UV cured resin (referred as "potting" hereafter), in order to prevent cable breakage during cabling and other issues. 2. Apply 3033 manufactured by THREEBOND CO., LTD. or any equivalent product for potting. Follow the instruction of the potting manufacturer for UV curing exposure. 3. Refer to the following conditions the potting area. 4. Use extreme care in handling the soldered and potted assembly. Too much stress applied to the cable could break it. 5. After soldering, check that no defect is found at soldered area. Examples of correct soldered and defective soldered state are shown below. Precautions and recommendations A A AA B B BB Correct soldering Solder shortage solder bridge Floating A 0 2.15 0 -0.4 1.25 0 -0.75 Enlarged view A 23.7 28.7 Number of contacts A

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal 3. Check the six fitting points after assembly and make sure that they are all correctly fitted together. [ Soldering to ground plate ] 1. Solder down the metal bar of the cable and ground plate after the assembly of the ground plate to enhance grounding capability and to protect against vertical cable puling forces. [ Coutions for ground plate assembly ] 1. Attach a ground plate separately provided as FX15S-41P-GND after the cable assembly process. 2. Place the ground plate onto the connector horizontally and pinch the two components from top and bottom with your fingers. Precautions and recommendations Pinch from top and bottom with fingers A Ground plate (FX15S-41P-GND) qAssembly wHorizontally from the top ePinch with fingers A Fitting Fitting Fitting Fitting Fitting Fitting A Ground plate does not hook the protrusion of connector housing Ground plate hooks the protrusion of connector housing How to check fitting points OK NG (Cut section of fitting points) Soldering Soldering A

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal Precautions and recommendations Connectors Packaging Triangle mark MatingMating Arrow mark Triangle mark Center mark Center mark ◆Packaging of the complete cable assemblies Exercise caution as not to tangle, twist or deform the complete cable assemblies when packaging. Special care should be taken NOT to apply any excessive stress to the individual wires. When removing the cable assemblies from the packaging do not pull on the wires. Make sure that the latch-locks are not interfering with packaging. ◆Mating of the connectors These connectors have a built in polarizing feature and will NOT mate when reversed. Do NOT try and force tem together. Align the connectors as shown on the illustration below and fully insert the plug into the receptacle. Confirm that both latch- locks are fully engaged. Additionally, this connector is equipped with reverse-insertion preventing mechanism, but a forced mating with a minimum force of 25N could damage the connector. Avoid any inappropriate mating, and perform the mating operation after checking the above-mentioned polarity indication. ◆Treatment after mating has been completed After mating, please take care to prevent any stress or load on the connector during the routing of cables. If a load of a minimum of 5N is applied on the cable, the cable (crimp contact) could come off. Further, if the entire cable is pulled with a minimum force of 20N, the connector could be broken. Please take extra care not to pull the cable and cause cable disconnection. If you use a small gauge coaxial plug, a repeated rotation could also cause cable disconnection. Do not use the cable by rotating it repeatedly. The rotation times should be limited to a maximum of 10 even if rotation is required for routing. If your use requires folding back of the cable over the base of the connector, make sure to maintain a large turn-back radius away from the connector base. Pulling in the horizontal direction: Not acceptable When you use the cable by turning it back Take a large radius Keep the turn-back position away from the root of the connector. Rotation in the vertical direction: Up to a maximum of 10 times Pulling in the vertical direction: Not acceptable

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal Precautions and recommendations B B B 2Pull straight back. Press Press Press Press B B Lock latches ◆Handling of Connectors after Mating Do not to apply excessive force to the connectors when routing the cable after mating. Pulling on the entire cable with a force of 20N or greater can damage the connector. Please take care not to pull the cable. ◆Un-mating of the connectors Equally depress both sides of the latch-locks as shown on the illustration and pull the plug straight out. Do not pull on the cables!

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal BTechnical Information (FX15S Series)

• Eye Pattern Waveforms (700MHz)
• Shielding Effectiveness (Shielding Characteristics Comparison Using a 2-chamber Shielded Room) Notes : The measurement value of “Without plug-side shields + Without receptacle-side shields” are taken as the zero level of the graph vertical axis dB. The respective results express the noise suppression effect (dB) as a relative comparison value to the “without shields” condition as the reference. With cable-side shields + With PCB-side shields With cable-side shields + Without PCB-side shields Without cable-side shields + With PCB-side shields Without cable-side shields + Without PCB-side shields ¤ (0 dB line) Frequency (GHz) Shielding Effect (dB) Measured shielding effectiveness for frequencies from 100MHz to 2GHz. Shielded connectors show noise suppression of 10db to 20dB, when compared with connectors without the shields. 1 m Cable Length 1.5 m Cable Length

FX15 Series●1mm Pitch Wire-to-Board Connectors supporting LVDS signal The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 10/2015. Contents are subject to change without notice for the purpose of improvements. 2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN TEL: +81-45-620-3526 Fax: +81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com USA: HIROSE ELECTRIC (U.S.A.), INC. SAN JOSE OFFICE

3255 Scott Boulevard, Building 7, Suite 101

Santa Clara, CA 95054 Phone : +1-408-253-9640 Fax : +1-408-253-9641 http://www.hirose.com/us/ USA: HIROSE ELECTRIC (U.S.A.), INC. CHICAGO OFFICE

580 Waters Edge Lane, Suite 205 Lombard IL

Phone : +1-630-282-6701 Mail : inquiries@hirose.com http://www.hirose.com/us/ USA: HIROSE ELECTRIC (U.S.A.), INC. HEADQUARTERS

2688 Westhills Court, Simi Valley, CA 93065-6235

Phone : +1-805-522-7958 Fax : +1-805-522-3217 http://www.hirose.com/us/ CHINA: HIROSE ELECTRIC (SHANGHAI) CO.,LTD. BEIJING BRANCH A1001, Ocean International Center, Building 56# East 4th Ring Middle Road, ChaoYang District, Beijing, 100025 Phone : +86-10-5165-9332 Fax : +86-10-5908-1381 http://www.hirose.com/cn/ TAIWAN: HIROSE ELECTRIC TAIWAN CO., LTD. 103 8F, No.87, Zhengzhou Rd., Taipei Phone : +886-2-2555-7377 Fax : +886-2-2555-7350 http://www.hirose.com/tw/ GERMANY: HIROSE ELECTRIC EUROPE B.V. GERMAN BRANCH Herzog-Carl-Strasse 4 D-73760 Ostfildern (Scharnhauser Park) Phone : +49-711-4560-02-1 Fax : +49-711-4560-02-299 http://www.hirose.com/eu/ GERMANY: HIROSE ELECTRIC EUROPE B.V. NUERNBERG OFFICE Muggenhofer Str. 136 90429 Nuernberg Phone : +49-911 32 68 89 63 Fax : +49-911 32 68 89 69 http://www.hirose.com/eu/ THE NETHERLANDS: HIROSE ELECTRIC EUROPE B.V. Hogehillweg #8 1101 CC Amsterdam Z-O Phone : +31-20-6557460 Fax : +31-20-6557469 http://www.hirose.com/eu/ GERMANY: HIROSE ELECTRIC EUROPE B.V. HANOVER OFFICE Bayernstr. 3, Haus C 30855 Langenhagen, Germany Phone : +49-511 97 82 61 30 Fax : +49-511 97 82 61 35 http://www.hirose.com/eu/ USA: HIROSE ELECTRIC (U.S.A.), INC. DETROIT OFFICE (AUTOMOTIVE) 17197 N. Laurel Park Drive, Suite 253, Livonia, MI 48152 Phone : +1-734-542-9963 Fax : +1-734-542-9964 http://www.hirose.com/us/ FRANCE: HIROSE ELECTRIC EUROPE B.V. PARIS OFFICE Regus La Garenne Colombes,Place de La Belgique,

71 Boulevard National La Garenne Colombes, 92250, France

Phone : +33 (0) 1 7082 3170 Fax : +33 (1) 7082 3101 http://www.hirose.com/eu/ UNITED KINGDOM: HIROSE ELECTRIC EUROPE BV (UK BRANCH)

4 Newton Court, Kelvin Drive, Knowlhill,

Milton Keynes, MK5 8NH Phone : +44-1908 202050 Fax : +44-1908 202058 http://www.hirose.com/eu/ CHINA: HIROSE ELECTRIC (SHANGHAI) CO., LTD. 1601, Henderson Metropolitan, NO.300, East Nanjing Road, Huangpu District, Shanghai, China 200001 Phone : +86-21-6391-3355 Fax : +86-21-6391-3335 http://www.hirose.com/cn/ HONG KONG: HIROSE ELECTRIC HONGKONG TRADING CO., LTD. Room 1001, West Wing, Tsim Sha Tsui Centre, 66 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong Phone : +852-2803-5338 Fax : +852-2591-6560 http://www.hirose.com/hk/ CHINA: HIROSE ELECTRIC TECHNOLOGIES (SHENZHEN) CO., LTD. Room 09-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre,

5002 Shen Nan Dong Road, Shenzhen City, Guangdong Province, 518008

Phone : +86-755-8207-0851 Fax : +86-755-8207-0873 http://www.hirose.com/cn/ SINGAPORE: HIROSE ELECTRIC SINGAPORE PTE. LTD.

10 Anson Road #26-16, International Plaza

079903, Singapore Phone : +65-6324-6113 Fax : +65-6324-6123 http://www.hirose.com/sg/ KOREA: HIROSE KOREA CO., LTD. 250, Huimanggongwon-ro, Siheung-si, Gyeonggi-do, Korea, 429-849 Phone : +82-31-496-7000,7124 Fax : +82-31-496-7100 http://www.hirose.co.kr/ INDIA: HIROSE ELECTRIC SINGAPORE PTE. LTD. DELHI LIAISON OFFICE Office NO.519, Regus-Green Boulevard, Level5, Tower C, Sec62, Plot B-9A, Block B, Noida, 201301, Uttar Pradesh, India Phone : +91-12-660-8018 Fax : +91-120-4804949 http://www.hirose.com/sg/ THAILAND: HIROSE ELECTRIC SINGAPORE PTE. LTD. BANGKOK OFFICE (REPRESENTATIVE OFFICE) Unit 4703, 47th FL., 1 Empire Tower, South Sathorn Road, Yannawa, Sathorn, Bangkok 10120 Thailand Phone : +66-2-686-1255 Fax : +66-2-686-3433 http://www.hirose.com/sg/ INDIA: HIROSE ELECTRIC SINGAPORE PTE. LTD. BANGALORE LIAISON OFFICE Unit No-403, 4th Floor, No-84, Barton Centre, Mahatma Gandhi (MG) Road, Bangalore 560 001, Karnataka, India Phone : +91-80-4120 1907 Fax : +91-80-4120 9908 http://www.hirose.com/sg/ MALAYSIA: HIROSE ELECTRIC SINGAPORE PTE. LTD. 1-10-07, Suntech @ Penang Cybercity (1164),Lintang Mayang Pasir 3,11950, Bayan Baru, Penang, Malaysia. Phone : +604-619-2564 Fax : +604-619-2574 http://www.hirose.com/sg/ Powered by TCPDF (www.tcpdf.org)