FSAL200_07 FAIRCHILD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 11
Technical content
Features
Typical 6Ω Switch Connection Between Two Ports Minimal Propagation Delay Through the Switch Low ICC Zero Bounce in Flow-Through Mode Control Inputs Compatible with TTL Level Rail-to-Rail Signal Handling Route Communications Signals Include: - 10/100 Ethernet - 100VG—AnyLAN - ATM25 - SONET OCI 51.8Mbps - USB1.1 - T1/E1 - Token Ring 4/16Mbps
Description
The Fairchild Switch FSAL200 is a rail-to-rail quad 2:1 high-speed CMOS TTL-compatible analog multiplexer / de-multiplexer switch. The low on resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise. When OE is low, the select pin connects the A Port to the selected B Port output. When OE is high, the switch is open and a high-impedance state exists between the two ports.
Ordering Information
Part Number Package Description Packing Method FSAL200MTC 16-Lead Thin Shrink Small Outline Pa ckage(TSSOP), JEDEC MO-153, 4.4mm Wide Rails FSAL200MTCX 16-Lead Thin Shrink Small Outline Package(TSSOP), JEDEC MO-153, 4.4mm Wide Tape and Reel FSAL200QSC 16-Lead Quarter Size Outline Package (QSOP), JEDEC MO-137, 0.150" Wide Rails FSAL200QSCX 16-Lead Quarter Size Outline Package (QSOP), JEDEC MO-137, 0.150" Wide Tape and Reel All packages are Pb-free per JEDEC standard J-SDD-020B.
© 2002 Fairchild Semiconductor Corporation www.fairchildsemi.com FSAL200 Rev. 1.7.1 3 FSAL200 — Wide Bandwidth Quad 2:! Analog Multiplexer / De-multiplexer Switch Absolute Maximum Ratings Stresses exceeding the absolute maximum ratings may dam age the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit VCC Supply Voltage -0.5 7.0 V VSW DC Switch Voltage (1) -0.5 0.5 V VIN DC Input Voltage (1) -0.5 7.0 V IIK DC Input Diode Current at (I IK) VIN < 0V -50 mA IOUT DC Output Current 120 mA ICC/IGND DC V CC or Ground Current ±100 mA PD Power Dissipation at 85°C 0.5 W TSTG Storage Temperature Range -65 +150 °C TA Ambient Temperature with Power Applied -40 +85 °C Note: 1. Input and output negative ratings may be exceeded if input and output diode current ratings are observed. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ens ure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol Parameter Min. Max. Unit VCC Supply Voltage 3.0 5.5 V VIN Control Input Voltage (2) 0 V CC V VSW Switch Input Voltage V CC V VOUT Output Voltage V CC V TA Operating Temperature -40 +85 °C Control Input VCC=2.3V -3.6V 0 10 tr,tf Input Rise and Fall Time Control Input VCC=4.5V -5.5V 0 5 ns/V θJA Thermal Resistance in Still Sir °C/W Note: 2. Control input must be held HIGH or LOW and it must not float.
© 2002 Fairchild Semiconductor Corporation www.fairchildsemi.com FSAL200 Rev. 1.7.1 4 FSAL200 — Wide Bandwidth Quad 2:! Analog Multiplexer / De-multiplexer Switch Typical values are at 25°C unless otherwise specified. TA=-40°C to +85°C Symbol Parameter Conditions V CC(V) Min. Typ. Max. Units 4.5 to 5.5 2.0 VIH Input Voltage High 3.0 to 3.6 2.0 V 4.5 to 5.5 -0.5 0.8 VIL Input Voltage Low V IOZ Off State Leakage Current 0 ≤ VIN ≤ 5.5V 0 to 5.5 100 µA ION=10 -30mA 4.5 to 5.5 6 12 RON Switch On Resistance (3) ION=10 -30mA 3.0 to 3.6 15 22 Ω VIN=VCC or GND 5.5 ±1 IIN Control Input Leakage VIN=VCC or GND 3.6 µA ICC Quiescent Supply Current, All Channels Off VIN=VCC or GND, IOUT=0 5.5 1 µA Analog Signal Range V CC 0 V CC V ΔRON On Resistance Matching Between Channels(3)(4) IA=-10 mA, VBN=2.1 3.0 to 3.6 1.0 3.0 Ω 4.5 to 5.5 100 IO Output Current B n, Bn, S-0V to 5V 3.0 to 3.6 80 mΑ A1, B1, B2=0V to 5V 4.5 to 5.5 3 RFLAT(ON) On Resistance Flatness (3)(5) A1, B1, B2=0V to 5V 3.0 to 3.6 Ω Notes: 3. Measured by the voltage drop between the A and B pins at the indicated current through the switch. On resistance is determined by the lower of the voltages on the two (A or B ports). 4. ΔRON = RON maximum – RON minimum measured at identical VCC, temperature, and voltage levels. 5. Flatness is defined as the difference between the maximum and minimum value of on resistance over the specified range of conditions.
Figure 11. 16-lead, Quarter Size Outline Package (QSOP), JEDEC MO-137. 0.150” wide
Figure 12. 16-lead, Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm wide
© 2002 Fairchild Semiconductor Corporation www.fairchildsemi.com FSAL200 Rev. 1.7.1 10 FSAL200 — Wide Bandwidth Quad 2:1 Analog Multiplexer / De-multiplexer Switch TRADEMARKS The following are registered and unregistered trademarks and service marks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACEx® Build it Now™ CorePLUS™ CROSSVOLT™ CTL™ Current Transfer Logic™ EcoSPARK Fairchild® Fairchild Semiconductor® FACT Quiet Series™ FACT FAST® FastvCore™ FPS™ FRFET® Global Power Resource SM Green FPS™ Green FPS™ e-Series™ GTO™ i-Lo™ IntelliMAX™ ISOPLANAR™ MegaBuck™ MICROCOUPLER™ MicroFET™ MicroPak™ MillerDrive™ Motion-SPM™ OPTOLOGIC OPTOPLANAR® PDP-SPM™ Power220® Power247® POWEREDGE® Power-SPM™ PowerTrench® Programmable Active Droop™ QFET® QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ SMART START™ SPM® STEALTH™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SyncFET™ The Power Franchise TinyBoost™ TinyBuck™ TinyLogic® TINYOPTO™ TinyPower™ TinyPWM™ TinyWire™ μSerDes™ UHC® UniFET™ VCX™ DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contai ns preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild Semiconductor. The datasheet is printed for reference information only. Rev. I31
© 2002 Fairchild Semiconductor Corporation www.fairchildsemi.com FSAL200 Rev. 1.7.1 11 FSAL200 — Wide Bandwidth Quad 2:1 Analog Multiplexer / De-multiplexer Switch