FSA646 ONSEMI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

Features

  • Switch Type: SPDT (10x)
  • Signal Types: ♦ MIPI, D−PHY
  • VCC: 1.5 to 5.0 V
  • Input Signals: 0 to 1.3 V
  • RON: ♦ 6 /C0087 Typical HS MIPI ♦ 6 /C0087 Typical LP MIPI
  • /C0068RON: 0.1 /C0087 Typical LP & HS MIPI
  • /C0068RON_FLAT: 0.9 /C0087 Typical LP & HS MIPI
  • ICCZ: 1 /C0109A Maximum
  • ICC: 32 /C0109A Typical
  • OIRR: −24 dB Typical
  • Bandwidth: 2500 MHz Minimum
  • Xtalk: −30 dB Typical
  • CON: 1.5 pF Typical
  • Skew (P), Skew (O): 6 ps Typical

Applications

  • Cellular Phones, Smart Phones
  • Tablets
  • Laptops
  • Displays www.onsemi.com WLCSP36, 2.43x2.43x0.4 CASE 567WJ See detailed ordering and shipping information on page 2 of this data sheet.

ORDERING INFORMATION

A = Assembly Location WL = Wafer Lot YY = Year WW = Work Week /C0071 = PB−Free Package (Bottom View) XXXXXXX XXXXXXX AWLYYWW/C0071

Figure 3. Top Through View Table 1. BALL−TO−PIN MAPPINGS

www.onsemi.com ABSOLUTE MAXIMUM RATINGS Symbol Parameter Min. Max. Unit VCC Supply Voltage −0.5 6.0 V VCNTRL DC Input Voltage (/OE, SEL) (Note 1) −0.5 VCC V VSW DC Switch I/O Voltage (Note 1,2) −0.3 1.8 V IIK DC Input Diode Current −50 mA IOUT DC Output Current 25 mA TSTG Storage Temperature −65 +150 °C ESD Human Body Model, JEDEC: JESD22−A114 All Pins 2.0 kV Charged Device Model, JEDEC: JESD22−C101 1.0 IEC 61000−4−2 System Contact 8.0 Air Gap 15.0 Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. The input and output negative ratings may be exceeded if the input and output diode current ratings are observed. 2. V SW refers to analog data switch paths. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min. Max. Unit VCC Supply Voltage 1.5 5.0 V VCNTRL Control Input Voltage (SEL, /OE) (Note 3) 0 VCC V VSW Switch I/O Voltage (CLKn, Dn, CLKAn, CLKBn, Dan, DBn) −HS Mode 0 0.3 V −LS Mode 0 1.3 V TA Operating Temperature −40 +85 °C Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. 3. The control inputs must be held HIGH or LOW; they must no float. DC AND TRANSIENT CHARACTERISTICS (TA = 25°C unless otherwise specified) Symbol Parameter Conditions VCC (V) TA = −40 to +85/C0053C UnitMin. Typ. Max. VIK Clamp Diode Voltage (/OE, SEL) IIN = −18 mA 1.5 −1.2 −0.6 V VIH Input Voltage High SEL, /OE 1.5 to 5 1.3 V VIL Input Voltage Low SEL, /OE 1.5 to 5 0.5 V IIN Control Input Leakage (/OE, SEL) VCNTRL = 0 to VCC 5 −0.5 0.5 /C0109A INO(OFF) INC(OFF) Off Leakage Current of Port CLKAn, Dan, CLKBn and DBn VSW = 0.0 ≤ DATA ≤ 1.3 V 5 −0.5 0.5 /C0109A IA(ON) ON Leakage Current of Common Ports (CLKn, Dn) VSW = 0.0 ≤ DATA ≤ 1.3 V 5 −0.5 0.5 /C0109A IOFF Power−Off Leakage Current (All I/O Ports) VSW = 0.0 or 1.3 V 0 −0.5 0.5 /C0109A IOZ Off−State Leakage VSW = 0.0 ≤ DATA ≤ 1.3 V /OE = High 5 −0.5 0.5 /C0109A

www.onsemi.com DC AND TRANSIENT CHARACTERISTICS (TA = 25°C unless otherwise specified) (continued) Symbol Unit TA = −40 to +85/C0053C VCC (V)ConditionsParameterSymbol UnitMax.Typ.Min.VCC (V)ConditionsParameter RON_MIPI_HS Switch On Resistance for HS MIPI Applications (Note 4) ION = −8 mA, /OE = 0 V, SEL = VCC or 0 V, CLKA, CLKB, DBN or DAN = 0.2 V 1.5 6 /C0087 2.5 3.3 RON_MIPI_LP Switch On Resistance for LP MIPI Applications (Note 4) ION = −8 mA, /OE = 0 V, SEL = VCC or 0 V, CLKA, CLKB, DBN or DAN = 1.2 V 1.5 6 /C0087 2.5 3.3 /C0068RON_MIPI_HS On Resistance Matching Between HS MIPI Channels (Note 4) ION = −8 mA, /OE = 0 V, SEL = VCC or 0 V, CLKA, CLKB, DBN or DAN = 0.2 V 1.5 0.1 /C0087 2.5 3.3 /C0068RON_MIPI_LP On Resistance Matching Between LP MIPI Channels (Note 4) ION = −8 mA, /OE = 0 V, SEL = VCC or 0 V, CLKA, CLKB, DBN or DAN = 1.2 V 1.5 0.1 /C0087 2.5 3.3 RON_FLAT_MIPI_HS On Resistance Flatness for HS MIPI Signals (Note 4) ION = −8 mA, /OE = 0 V, SEL = VCC or 0 V, CLKA, CLKB, DBN or DAN = 0 to 0.3 V 1.5 0.9 /C0087 2.5 3.3 RON_FLAT_MIPI_LP On Resistance Flatness for LP MIPI Signals (Note 4) ION = −8 mA, /OE = 0 V, SEL = VCC or 0 V, CLKA, CLKB, DBN or DAN = 0 to 1.3 V 1.5 0.9 /C0087 2.5 3.3 ICC Quiescent Supply Current (Includes Change Pump) VSEL = 0 or VCC, IOUT = 0, /OE = 0 V 5 30 /C0109A ICCZ Quiescent Supply Current (High Impedance) VSEL = 0 or VCC, IOUT = 0, /OE = 0 V 5 1 /C0109A ICCT Increase in ICC Current Per Control Voltage and VCC VSEL = 0 or VCC, /OE = 1.5 V 5 1 /C0109A 4. Measured by the voltage drop between A and B pins at the indicated current through the switch. On resistance is determined by the lower of the voltage on the two (A or B ports). AC ELECTRICAL CHARACTERISTICS (VCC = 3.3 V and TA = 25°C unless otherwise specified) Symbol Parameter Conditions VCC (V) TA = −40 to +85/C0053C UnitMin. Typ. Max. tINIT Initialization Time VCC to Output (Note 5) RL = 50 /C0087, CL = 0 pF, VSW = 0.6 V 1.5 to 5 60 /C0109s tEN Enable Time /OE to Output RL = 50 /C0087, CL = 0 pF, VSW = 0.6 V 1.5 to 5 60 150 /C0109s tDIS Disable Time /OE to Output RL = 50 /C0087, CL = 0 pF, VSW = 0.6 V 1.5 to 5 35 250 ns

www.onsemi.com AC ELECTRICAL CHARACTERISTICS (VCC = 3.3 V and TA = 25°C unless otherwise specified) (continued) Symbol Unit TA = −40 to +85/C0053C VCC (V)ConditionsParameterSymbol UnitMax.Typ.Min.VCC (V)ConditionsParameter tON Turn−On Time SEL to Output RL = 50 /C0087, CL = 0 pF, VSW = 0.6 V 1.5 to 5 350 1100 ns tOFF Turn−Off Time SEL to Output RL = 50 /C0087, CL = 0 pF, VSW = 0.6 V 1.5 to 5 125 800 ns tBBM Break−Before−Make Time RL = 50 /C0087, CL = 0 pF, VSW = 0.6 V 1.5 to 5 50 450 ns tPD Propagation Delay (Note 5) CL = 0 pF, RL = 50 /C0087 1.5 to 5 30 67 100 ps OIRR Off Isolation for MIPI (Note 5) RL = 50 /C0087, f = 1250 MHz, /OE = HIGH, VSW = 0.2 VPP 1.5 to 5 −24 dB XTALK Crosstalk for MIPI (Note 5) RL = 50 /C0087, f = 1250 MHz, SEL = High, VSW = 0.2 VPP 1.5 to 5 −30 −25 dB RL = 50 /C0087, f = 1250 MHz, SEL = Low, VSW = 0.2 VPP −30 −25 BW (Insertion Loss) −3 db Bandwidth (Note 5) RL = 50 /C0087, CL = 0 pF, VSW = 0.2 VPP 1.5 to 5 2500 MHz IL Insertion Loss at 750 MHz (Note 5) RL = 50 /C0087, CL = 0 pF, VSW = 0.2 VPP 1.5 to 5 −0.7 dB 5. Guaranteed by characterization. HIGH−SPEED−RELATED AC ELECTRICAL CHARACTERISTICS Symbol Parameter Conditions VCC (V) TA = −40 to +85/C0053C UnitMin. Typ. Max. tSK(P) HS Mode Skew of Oppo- site Transitions of the Same Output (Note 6) RL = 50 /C0087, CL = 0 pF, VSW = 0.3 V 1.5 to 5 6 ps tSK(O) HS Mode Skew of Channel−to−Channel Single−Ended Skew (Note 6) RL = 50 /C0087, CL = 0 pF, VSW = 0.3 V 1.5 to 5 6 ps 6. Guaranteed by characterization. CAPACITANCE Symbol Parameter Conditions TA = −40 to +85/C0053C UnitMin. Typ. Max. CIN Control Pin Input Capacitance (Note 7) VCC = 0 V, f = 1 MHz 2.1 pF CON On Capacitance (Note 7) VCC = 3.3 V, /OE = 0 V, f = 1250 MHz (in HS common value) 1.5 COFF On Capacitance (Note 7) VCC and /OE = 3.3 V, f = 1250 MHz (both sides in HS common value) 0.9 7. Guaranteed by characterization. The table below pertains to the Packaging information on the following page. PRODUCT SPECIFIC DIMENSIONS D E X Y 2.43 mm 2.43 mm 0.215 mm 0.215 mm

WLCSP36 2.43x2.43x0.4 CASE 567WJ ISSUE O DATE 02 MAY 2018 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. 98AON87484GDOCUMENT NUMBER: DESCRIPTION: Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red. PAGE 1 OF 1WLCSP36 2.43x2.43x0.4 © Semiconductor Components Industries, LLC, 2018 www.onsemi.com

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries i n the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property . A listing of ON Semiconductor’s product/patent ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, reg ulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative