FPL11PT CHENMKO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
- Low leakage current * Fast recovery times for high efficiency * Glass passivated junction * High temperature soldering guaranteed : 260oC/10 seconds at terminals FPL11PT THRU FPL17PT CHENMKO ENTERPRISE CO.,LTD SURFACE MOUNT GLASS PASSIVATED FAST RECOVERY SILICON RECTIFIER VOLTAGE RANGE 50 - 1000 Volts CURRENT 1.0 Ampere ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) NOTES : Maximum Full Load Reverse Current Average, Full Cycle at TA = 55oC CHARACTERISTICS SYMBOL UNITS 1.3 5.0 150 250 500 uAmps 100 uAmps nSec VoltsMaximum Instantaneous Forward Voltage at 1.0 A DC Maximum DC Reverse Current at Rated DC Blocking Voltage at TA = 25oC MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current TL = 110oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 1) Maximum Thermal Resistance Operating and Storage Temperature Range SYMBOL VRRM VRMS VDC IO CJ R JA VF Maximum Reverse Recovery Time (Note 4) trr IR TJ, TSTG IFSM FPL11PT FPL12PT UNITS Volts Volts Volts Amps FPL13PT 200 140 200 FPL14PT 280 400 400 FPL15PT 600 420 600 FPL16PT 800 560 800 FPL17PT 1000 700 1000 1.0 -65 to +150 Amps pF oC / W oC / W oC 100 100 R JL 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 2. Thermal Resistance Junction to terminal 6.0 mm2 copper pads to each terminal 3. Thermal Resistance Junction to ambient 6.0 mm2 copper pads to each terminal 4. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A (Note 2) (Note 3) 2004-7 SMP 2 1 FEATURE CIRCUIT *Small Surface Mounting Type. (SMP)
3 Dimensions in inches and (millimeters) SMP
0.005 (0.15 Min.) 0.077 (1.95) 0.042 (1.07) 0.081 (2.05) 0.077 (1.95) 0.212 (5.38) 0.208 (5.29) 0.264 (6.70) 0.254 (6.46) 0.055 (1.40) 0.051 (1.30) 0.170 (4.31) 0.163 (4.15) (1) (2) (3) 0.019 (0.50 Min.) 0.019 (0.50 Min.) FPL11PT FPL12PT FPL13PT FPL14PT FPL15PT FPL16PT FPL17PT
RATING CHARACTERISTIC CURVES ( FPL11PT THRU FPL17PT ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC FIG. 3 - TYPICAL REVERSE CHARACTERISTICS FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 6 - TYPICAL JUNCTION CAPACITANCEFIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT INSTANTANEOUS REVERSE CURRENT, (uA)PEAK FORWARD SURGE CURRENT, ( A ) JUNCTION CAPACITANCE, ( pF ) REVERSE VOLTAGE, ( V )NUMBER OF CYCLES AT 60 Hz INSTANTANEOUS FORWARD VOLTAGE, ( V )PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) INSTANTANEOUS FORWARD CURRENT, ( A ) NONINDUCTIVE NONINDUCTIVE D.U.T( + )
25 Vdc
(approx) ( - ) 1 NON- INDUCTIVE OSCILLOSCOPE (NOTE 1) PULSE GENERATOR (NOTE 2) ( - ) ( + ) NOTES: 1. Rise Time = 7 ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10 ns max. Source Impedlance= 50 ohms. +0.5A -0.25A -1.0A trr 1cm SET TIME BASE FOR 50/100 nS/cm AVERAGE FORWARD CURRENT, ( A ) LEAD TEMPERATURE ( O C ) FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE Single Phase Half Wave 60Hz Resistive or Inductive Load 1.50 1.00 .25 .50 .75 1.25 250 50 75 100 125 150 175 1.0 0.1 .01 Pulse Width = 300uS 1% Duty Cycle TJ =25oC TJ =25oC TJ =25oC TJ =100oC .01 .04 1.0 4.0 100 200 100 .1 .2 .4 1.0 2 4 10 20 40 1001 2 5 10 20 50 100 8.3ms Single Half Sine-Wave (JEDEC Method) 50 10