FPF2163 FAIRCHILD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 13
Technical content
Features
1.8 to 5.5V Input Voltage Range Controlled Turn-On 0.15-1.5A Adjustable Current Limit Undervoltage Lockout Thermal Shutdown <2uA Shutdown Current Auto Restart Fast Current limit Response Time 5us to Moderate Over Currents 30ns to Hard Shorts Fault Blanking Reverse Current Blocking RoHS Compliant
Applications
PDAs Cell Phones GPS Devices MP3 Players Digital Cameras Peripheral Ports Hot Swap Supplies General Description The FPF2163, FPF2164, and FPF2165 is a series of load switches which provides full protection to systems and loads which may encounter large current conditions. These devices contain a 0.12 Ω current-limited P-channel MOSFET which can operate over an input voltage range of 1.8-5.5V. Internally, current is prevented from flowing when the MOSFET is off and the output voltage is higher than the input voltage. Switch control is by a logic input (ON) capable of interfacing directly with low voltage control signals. Each part contains thermal shutdown protection which shuts off the switch to prevent damage to the part when a cont inuous over-current condition causes excessive heating. When the switch current reaches the current limit, the parts operate in a constant-current mode to prohibit excessive currents from causing damage. For the FPF2163 and FPF2164, if the constant current condition still persists after 30ms, these parts will shut off the switch and pull the fault signal pin (FLAGB) low. The FPF2163 has an auto-restart feature which will turn the switch on again after 450ms if the ON pin is still active. The FPF2164 does not have this auto-restart feature so the switch will remain off until the ON pin is cycled. The FPF2165 will not turn off after a current limit fault, but will rather remain in the constant current mode indefinitely. The minimum current limit is 150mA. These parts are available in a space-saving 6 pin 2X2 MLP package.
Ordering Information
[mA] Current Limit Blanking Time [ms] Auto-Restart Time [ms] ON Pin Activity Top Mark FPF2163 150-1500 15/30/60 225/450/900 Active HI 163 FPF2164 150-1500 15/30/60 NA Active HI 164 FPF2165 150-1500 0 NA Active HI 165 BOTTOM TOP Pin 1
2 www.fairchildsemi.com FPF2163/4/5 Rev. C3 FPF2163/4/5 Full Function Load Switch with Adjustable Current Limit Typical Application Circuit Functional Block Diagram OFF ON ON VIN GND FPF2163/4/5 ISET VOUT TO LOAD FLAGB UVLO THERMAL SHUTDOWN CURRENT LIMIT CONTROL LOGIC VIN ON ISET FLAGB GND REVERSE CURRENT BLOCKING VOUT
3 www.fairchildsemi.com FPF2163/4/5 Rev. C3 FPF2163/4/5 Full Function Load Switch with Adjustable Current Limit Pin Configuration Pin Description Absolute Maximum Ratings Recommended Operating Range
Electrical Characteristics
1 ISET Current Limit Set Input: A resistor from ISET to ground sets the current limit for the switch. 2V IN Supply Input: Input to the power switch and the supply voltage For the IC 3V OUT Switch Output: Output of the power switch
4 FLAGB Fault Output: Active LO, open drain output which indicates an over current supply under
voltage or over temperature state.
5 GND Ground
6 ON ON Control Input
Parameter Min. Max. Unit VIN, VOUT, ON, FLAGB, ISET to GND -0.3 6 V Power Dissipation 1.2 W Operating and Storage Junction Temperature -65 150 °C Thermal Resistance, Junction to Ambient 86 °C/W Electrostatic Discharge Protection HBM 4000 V MM 400 V Parameter Min. Max. Unit VIN 1.8 5.5 V Ambient Operating Temperature, TA -40 85 °C Parameter Symbol Conditions Min. Typ. Max. Units Basic Operation Operating Voltage V IN 1.8 5.5 V Quiescent Current I Q IOUT = 0mA VIN = 1.8V 63 100 µAVIN = 3.3V 68 VIN = 5.5V 77 120 On-Resistance R ON TA = 25°C, IOUT = 200mA 120 160 mΩ TA = -40 to +85°C, IOUT = 200mA 135 ON Input Logic High Voltage (ON) V IH VIN = 1.8V 0.8 V VIN = 5.5V 1.4 ISET VIN VOUTFLAGB ON 2X2 MicroFET-6 GND
4 www.fairchildsemi.com FPF2163/4/5 Rev. C3 FPF2163/4/5 Full Function Load Switch with Adjustable Current Limit Electrical Characteristics Cont. Note 1: Package power dissipation on 1square inch pad, 2 oz copper board. Parameter Symbol Conditions Min. Typ. Max. Units ON Input Logic Low Voltage V IL VIN = 1.8V 0.5 V VIN = 5.5V 1 ON Input Leakage V ON = VIN or GND -1 1 µA VIN Shutdown Current VON = 0V, VIN = 5.5V, VOUT = short to GND -2 2 µA FLAGB Output Logic Low Voltage V IN = 5V, ISINK = 10mA 0.05 0.2 V VIN = 1.8V, ISINK = 10mA 0.12 0.3 FLAGB Output High Leakage Current V IN = 5V, Switch on 1 µA Reverse Block VOUT Shutdown Current VON = 0V, VOUT = 5.5V, VIN = short to GND -2 2 µA Protections Current Limit I LIM VIN = 3.3V, VOUT = 3.0V, RSET = 345Ω 600 800 1000 mA Min. Current Limit I LIM(min.) VIN = 3.3V, VOUT = 3.0V 150 mA Thermal Shutdown Shutdown Threshold 140 °CReturn from Shutdown 130 Hysteresis 10 Under Voltage Shutdown UVLO V IN Increasing 1.55 1.65 1.75 V Under Voltage Shutdown Hysteresis 50 mV Dynamic Turn on time t ON RL = 500Ω, CL = 0.1µF 25 µs Turn off time t OFF RL = 500Ω, CL = 0.1µF 45 µs VOUT Rise Time t RISE RL = 500Ω, CL = 0.1µF 10 µs VOUT Fall Time t FALL RL = 500Ω, CL = 0.1µF 110 µs Over Current Blanking Time t BLANK FPF2163, FPF2164 15 30 60 ms Auto-Restart Time t RSTRT FPF2163 225 450 900 ms Short Circuit Response Time VIN = VOUT = 3.3V. Moderate Over-Current Condition. 5µ s VIN = VOUT = 3.3V. Hard Short. 30 ns
9 www.fairchildsemi.com FPF2163/4/5 Rev. C3 FPF2163/4/5 Full Function Load Switch with Adjustable Current Limit Description of Operation The FPF2163, FPF2164, and FPF2165 are current limited switches that protect systems and loads which can be damaged or disrupted by the application of high currents. The core of each device is a 0.12 Ω P-channel MOSFET and a controller capable of functioning over a wide input operating range of 1.8- 5.5V. The controller protects against system malfunctions through current limiting, under-voltage lockout and thermal shutdown. The current limit is adjustable from 150mA to 1.5A through the selection of an external resistor. On/Off Control The ON pin controls the state of the switch. When ON is high, the switch is in the on state. Activating ON continuously holds the switch in the on state so long as there is no fault. For all versions, an under-voltage on V IN or a junction temperature in excess of 140°C overrides the ON control to turn off the switch. In addition, excessive currents will cause the switch to turn off in the FPF2163 and FPF2164. The FPF2163 has an Auto-Restart feature which will automatically turn the switch on again after 450ms. For the FPF2164, the ON pin must be toggled to turn-on the switch again. The FPF2165 does not turn off in response to an over current condition but instead remains operating in a constant current mode so long as ON is active and the thermal shutdown or under-voltage lockout have not activated. Fault Reporting Upon the detection of an over-current, an input under-voltage, or an over-temperature conditi on, the FLAGB signals the fault mode by activating LO. For the FPF2163 and FPF2164, the FLAGB goes LO at the end of t he blanking time while FLAGB goes LO immediately for the FPF2165. FLAGB remains LO through the Auto-Restart Time for the FPF2165. For the FPF2164, FLAGB is latched LO and ON must be toggled to release it. With the FPF2165, FLAGB is LO during the faults and immediately returns HI at the end of the fault condition. FLAGB is an open-drain MOSFET which requires a pull-up resistor between VIN and FLAGB. During shutdown, the pull-down on FLAGB is disabled to reduce current draw from the supply. Current Limiting The current limit ensures that the current through the switch doesn't exceed a maximum value while not limiting at less than a minimum value. The current at which the parts will limit is adjustable through the selection of an external resistor connected to ISET. Information for selecting the resistor is found in the Application Info section. The FPF2163 and FPF2164 have a blanking time of 30ms, nominally, during which the switch will act as a constant current source. At the end of the blanking time, the switch will be turned-off. The FPF2165 has no current limit blanking period so it will remain in a constant current state until the ON pin is deactivated or the thermal shutdown turns-off the switch. For preventing the switch from large power dissipation during heavy load a short circuit detection feature is introduced. Short circuit condition is detected by observing the output voltage. The switch is put into short circuit current limiting mode if the switch is loaded with a heavy load. When the output voltage drops below VSCTH, short circuit detection threshold voltage, the current limit value re-con ditioned and short circuit current limit value is decreased to 62.5% of the current limit value. This keeps the power dissipation of the part below a certain limit even at dead short conditions at 5.5V input voltage. The VSCTH value is set to be 1V. At around 1.1V of output voltage the switch is removed from short circuit current limiting mode and the current limit is set to the current limit value. Under-Voltage Lockout The under-voltage lockout turns-off the switch if the input voltage drops below the under-voltage lockout threshold. With the ON pin active the input voltage rising above the under- voltage lockout threshold will c ause a controlled turn-on of the switch which limits current over-shoots. Reverse Current Blocking The entire FPF2163/65 family has a Reverse Current Blocking feature that protects input source against current flow from output to input. For a standard USB power design, this is an important feature which protects the USB host from being damaged due to reverse current flow on V BUS. The reverse current blocking feature is active when the load switch is turned off. If ON pin is LO and output voltage become greater than input voltage, no current can flow from the output to the input . The FLAGB operation is independent of the Reverse Current blocking feature and will not r eport a fault condition if this feature is activated. Thermal Shutdown The thermal shutdown protects the die from internally or exter- nally generated excessive temperatures. During an over-tem- perature condition the FLAGB is activated and the switch is turned-off. The switch automatically turns-on again if tempera- ture of the die drops below the threshold temperature.
10 www.fairchildsemi.com FPF2163/4/5 Rev. C3 FPF2163/4/5 Full Function Load Switch with Adjustable Current Limit
Application Information
1.8V-5.5V C1 = 0.1µF RSET C2 = 0.1µF R2 = 499Ω FLAGB Setting Current Limit The FPF2163, FPF2164, and FPF2165 have a current limit which is set with an external resistor connected between ISET and GND. This resistor is selected by using the following equation, RSET is in Ohms and that of ILIM is Amps The table below can also be used to select R SET. A typical application would be the 500mA current that is required by a single USB port. Using the table below an appropriate selection for the R SET resistor would be 394 Ω. This will ensure that the port load could draw 525mA, but not more than 875mA. Likewise for a dual port system, an R SET of 185Ω would always deliver at least 1125mA and never more than 1875mA Current Limit Various RSET Values Input Capacitor To limit the voltage drop on the input supply caused by transient in-rush currents when the switch is turned on into a discharged load capacitor or a short-circui t, a capacitor needs to be placed between VIN and GND. A 0.1uF ceramic capacitor, C IN, placed close to the pins is usually sufficient. Higher values of C IN can be used to further reduce the voltage drop. Output Capacitor A 0.1uF capacitor C OUT, should be placed between V OUT and GND. This capacitor will prev ent parasitic board inductances from forcing VOUT below GND when the switch turns-off. For the FPF2163 and FPF2164, the total output capacitance needs to be kept below a maximum value, C OUT(max), to prevent the part from registering an over -current condition and turning-of f the switch. The maximum output capacitance can be determined from the following formula, Power Dissipation During normal operation as a switch, the power dissipated in the part will depend upon the level at which the current limit is set. The maximum allowed setting for the current limit is 1.5A and this will result in a power dissipation of, If the part goes into current limit the maximum power dissipation will occur when the output is shorted to ground. For the FPF2163, the power dissipation will scale by the Auto-Restart Time, t RSTRT, and the Over Current Blanking Time, t BLANK, so that the maximum power dissipated is, RSET [Ω] Min. Current Limit [mA] Typ. Current Limit [mA] Max. Current Limit [mA] 185 1125 1500 1875 220 938 1250 1562 275 750 1000 1250 306 675 900 1125 345 600 800 1000 394 525 700 875 460 450 600 750 550 375 500 625 610 338 450 563 690 300 400 500 790 263 350 438 920 225 300 375 1100 188 250 313 1380 150 200 250 1830 113 150 188 (2)RSET 275.6 ILIM (1)COUT max() ILIM max() tBLANK min()× VIN (3) Pm a x() tBLANK
11 www.fairchildsemi.com FPF2163/4/5 Rev. C3 FPF2163/4/5 Full Function Load Switch with Adjustable Current Limit This is more power than the package can dissipate, but the thermal shutdown of the part will activate to protect the part from damage due to excessive heating. When using the FPF2164, attention must be given to the manual resetting of the part. The junction temperature will only be able to increase to the thermal shutdown threshold. Once this temperature has been reached, toggling ON will not turn-on t he switch until the junction temperature drops. For the FPF2165, a short on the output will cause the part to operate in a constant current state dissipating a worst case power of, This large amount of power will activate the thermal shutdown and the part will cycle in and out of thermal shutdown so long as the ON pin is active and the short is present. Board Layout For best performance, all traces should be as short as possible. To be most effective, the input and output capacitors should be placed close to the device to minimize the effects that parasitic trace inductances may have on normal and short-circuit operation. Using wide traces for V IN, VOUT and GND will help minimize parasitic el ectrical effects along with minimizing the case to ambient thermal impedance. (4)Pm a x() VIN max() ILIM max()×= 5.5 1.5×= 8.25W=
12 www.fairchildsemi.com FPF2163/4/5 Rev. C3 FPF2163/4/5 Full Function Load Switch with Adjustable Current Limit Dimensional Outline and Pad Layout
13 www.fairchildsemi.com FPF2163/4/5 Rev. C3 FPF2163/4/5 Full Function Load Switch with Adjustable Current Limit TRADEMARKS The following are registered and unregistered trademarks and service marks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT D ESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHE RS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIF ICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or s ystems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms ACEx® Build it Now™ CorePLUS™ CROSSVOLT™ CTL™ Current Transfer Logic™ EcoSPARK Fairchild® Fairchild Semiconductor® FACT Quiet Series™ FACT® FAST® FastvCore™ FPS™ FRFET Global Power ResourceSM Green FPS™ Green FPS™ e-Series™ GTO™ i-Lo™ IntelliMAX™ ISOPLANAR™ MegaBuck™ MICROCOUPLER™ MicroFET™ MicroPak™ Motion-SPM™ OPTOLOGIC OPTOPLANAR® PDP-SPM™ Power220® Power247® POWEREDGE® Power-SPM™ PowerTrench Programmable Active Droop™ QFET QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ SMART START™ SPM STEALTH™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SyncFET™ The Power Franchise TinyBoost™ TinyBuck™ TinyLogic TINYOPTO™ TinyPower™ TinyPWM™ TinyWire™ µSerDes™ UHC UniFET™ VCX™ Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Rev. I30