FPF2123_06 FAIRCHILD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 13
Technical content
Features
1.8 to 5.5V Input Voltage Range Controlled Turn-On 0.15-1.5A Adjustable Current Limit Undervoltage Lockout Thermal Shutdown <2uA Shutdown Current Auto Restart Fast Current limit Response Time 3us to Moderate Over Currents 20ns to Hard Shorts Fault Blanking Reverse Current Blocking
Applications
PDAs Cell Phones GPS Devices MP3 Players Digital Cameras Peripheral Ports Hot Swap Supplies General Description The FPF2123, FPF2124, and FPF2125 are a series of load switches which provide full protection to systems and loads which may encounter large current conditions. These devices contain a 0.125Ω current-limited P-channel MOSFET which can operate over an input voltage range of 1.8-5.5V. The current limit is settable using an external resistor. Internally, current is prevented from flowing when the MOSFET is off and the output voltage is higher than the input voltage. Switch control is by a logic input (ON) capable of interfacing directly with low voltage control signals. Each part contains thermal shutdown protection which shuts off the switch to prevent damage to the part when a continuous over-current condition causes excessive heating. When the switch current reaches the current limit, the parts operate in a constant-current mode to prohibit excessive currents from causing damage. For the FPF2123 and FPF2124 if the constant current condition still persists after 10ms, these parts will shut off the switch. The FPF2123 has an auto-restart feature which will turn the switch on again after 160ms if the ON pin is still active. The FPF 2124 does not have this auto-restart feature so the switch will remain off after a current limit fault until the ON pin is cycled. The FPF2125 will not turn off after a current limit fault, but will rather remain in the constant current mode indefinitely. The minimum current limit is 150mA. These parts are available in a space-saving 5 pin SOT23 package Typical Application Circuit
Ordering Information
[A] Current Limit Blanking Time [ms] Auto-Restart Time [ms] ON Pin Activity Top Mark FPF2123 0.15 - 1.5 5/10/20 80/160/320 Active HI 2123 FPF2124 0.15 - 1.5 5/10/20 NA Active HI 2124 FPF2125 0.15 - 1.5 Infinite NA Active HI 2125 OFF ON ON VIN GND FPF2123 - FPF2125 ISET VOUT TO LOAD
2 www.fairchildsemi.com FPF2123-FPF2125 Rev. C4 FPF2123-FPF2125 IntelliMAX™ Advanced Load Management Products Functional Block Diagram Pin Configuration Pin Description Pin Name Function 1V IN Supply Input: Input to the power switch and the supply voltage for the IC
2 GND Ground
3 ON ON Control Input
4 ISET Current Limit Set Input: A resistor from ISET to ground sets the current limit for the switch. 5V OUT Switch Output: Output of the power switch UVLO THERMAL SHUTDOWN CURRENT LIMIT CONTROL LOGIC VIN ON VOUT ISET GND REVERSE CURRENT BLOCKING VIN GND ON ISET VOUT SOT23-5
3 www.fairchildsemi.com FPF2123-FPF2125 Rev. C4 FPF2123-FPF2125 IntelliMAX™ Advanced Load Management Products Absolute Maximum Ratings Recommended Operating Range
Electrical Characteristics
Parameter Min. Max. Unit VIN, VOUT, ON, ISET to GND -0.3 6 V Power Dissipation @ TA = 25°C (note 1) 667 mW Operating Temperature Range -40 125 °C Storage Temperature -65 150 °C Thermal Resistance, Junction to Ambient 150 °C/W Electrostatic Discharge Protection HBM 4000 V MM 400 V Parameter Min. Max. Unit VIN 1.8 5.5 V Ambient Operating Temperature, TA -40 85 °C Parameter Symbol Conditions Min. Typ. Max Units Basic Operation Operating Voltage V IN 1.8 5.5 V Quiescent Current I Q IOUT = 0mA V IN = 1.8 to 3.3V 75 µA VIN = 3.3 to 5.5V 80 120 Shutdown Current I SHDN 2 µA Reverse Block Leakage Current I BLOCK 1 µA Latch-Off Current I LATCHOFF FPF2124 50 µA On-Resistance R ON TA = 25°C, IOUT = 50mA 125 160 mΩ TA = -40 to +85°C, IOUT = 50mA 150 ON Input Logic High Voltage (ON) V IH VIN = 1.8V 0.75 V VIN = 5.5V 1.30 ON Input Logic Low Voltage V IL VIN = 1.8V 0.5 V VIN = 5.5V 1.0 ON Input Leakage V ON = VIN or GND 1 µA Off Switch Leakage I SWOFF VON = 0V, VOUT = 0V 1 µA Protections Current Limit I LIM VIN = 3.3V, VOUT = 3.0V, RSET=576Ω 600 800 1000 mA Min. Current Limit I LIM(min.) VIN = 3.3V, VOUT = 3.0V 150 mA Thermal Shutdown Shutdown Threshold 140 °C Return from Shutdown 130 Hysteresis 10 Under Voltage Shutdown UVLO V IN Increasing 1.5 1.6 1.7 V Under Voltage Shutdown Hysteresis 50 mV
4 www.fairchildsemi.com FPF2123-FPF2125 Rev. C4 FPF2123-FPF2125 IntelliMAX™ Advanced Load Management Products Electrical Characteristics Cont. Note 1: Package power dissipation on 1square inch pad, 2 oz copper board. Parameter Symbol Conditions Min. Typ. Max Units Dynamic Turn on time t ON RL=500Ω, CL=0.1uF 25 µs Turn off time t OFF RL=500Ω, CL=0.1uF 70 µs VOUT Rise Time t R RL=500Ω, CL=0.1uF 12 µs VOUT Fall Time t F RL=500Ω, CL=0.1uF 200 µs Over Current Blanking Time t BLANK FPF2123, FPF2124 5 10 20 ms Auto-Restart Time t RESTART FPF2123 80 160 320 ms FPF2124, FPF2125 NA Short Circuit Response Time V IN = VON = 3.3V. Moderate Over-Current Condition. 3 µs VIN = VON = 3.3V. Hard Short. 20 µs
9 www.fairchildsemi.com FPF2123-FPF2125 Rev. C4 FPF2123-FPF2125 IntelliMAX™ Advanced Load Management Products Description of Operation The FPF2123, FPF2124, and FPF2125 are current limited switches that protect systems and loads which can be damaged or disrupted by the application of high currents. The core of each device is a 0.125 Ω P-channel MOSFET and a controller capable of functioning over a wide input operating range of 1.8-5.5V. The controller prot ects against system malfunctions through current limiting under-voltage lockout and thermal shutdown. The current limit is adjustable from 150mA to 1.5A through the selection of an external resistor. On/OffControl The ON pin controls the state of the switch. When ON is high, the switch is in the on state. Activating ON continuously holds the switch in the on state so long as there is no fault. For all versions, an under-voltage on V IN or a junction temperature in excess of 140°C overrides the ON control to turn off the switch. In addition, excessive currents will cause the switch to turn off in the FPF2123 and FPF2124. The FPF2123 has an Auto-Restart feature which will automatically turn the switch on again after 160ms. For the FPF2124, the ON pin must be toggled to turn-on the switch again. The FPF2125 does not turn off in response to an over current condition but instead remains operating in a constant current mode so long as ON is active and the thermal shutdown or under-voltage lockout have not activated. Current Limiting The current limit ensures that the current through the switch doesn't exceed a maximum value while not limiting at less than a minimum value. The current at which the parts will limit is adjustable through the selection of an external resistor connected to ISET. Information for selecting the resistor is found in the Application Info section. The FPF2123 and FPF2124 have a blanking time of 10ms, nominally, during which the switch will act as a constant current source. At the end of the blanking time, the switch will be turned-off. The FPF2125 has no current limit blanking peri od so it will remain in a constant current state until the ON pin is deactivated or the thermal shutdown turns-off the switch. Under-Voltage Lockout The under-voltage lockout turns-off the switch if the input voltage drops below the under-voltage lockout threshold. With the ON pin active, the input voltage rising above the under-voltage lockout threshold wi ll cause a controlled turn-on of the switch which limits current over-shoots. Thermal Shutdown The thermal shutdown protects the die from internally or externally generated excessive temperatures. During an over-temperature condition the switch is turned-off. The switch automatically turns-on again if the temperature of the die drops below the threshold temperature.
10 www.fairchildsemi.com FPF2123-FPF2125 Rev. C4 FPF2123-FPF2125 IntelliMAX™ Advanced Load Management Products
Application Information
5.5V C1=10uF RSET C2=0.1uF R2=110Ω 5.5V MAX Setting Current Limit The FPF2123, FPF2124, and FPF2125 have a current limit which is set with an external resistor connected between ISET and GND. This resistor is selected by using the following equation, R SET is in Ohms and that of ILIM is Amps The table below can also be used to select R SET. A typical application would be the 500mA current that is required by a single USB port. Using the table below an appropriate selection for the R SET resistor would be 604 Ω. This will ensure that the port load could draw 570mA, but not more than 950mA. Likewise for a dual port system, an R SET of 340Ω would always deliver at least 1120mA and never more than 1860mA. Input Capacitor To limit the voltage drop on the input supply caused by transient in-rush currents when the switch turns-on into a discharged load capacitance or a short-circuit, a capacitor needs to be placed between VIN and GND. A 0.1uF ceramic capacitor, C IN, placed close to the pins is usually sufficient. Higher values of C IN can be used to further reduce the voltage drop. Output Capacitor A 0.1uF capacitor, C OUT, should be placed between V OUT and GND. This capacitor will pr event parasitic board inductances from forcing V OUT below GND when the switch turns-off. For the FPF2123 and FPF2124, the total output capacitance needs to be kept below a maximum value, C OUT(max), to prevent the part from registering an over-cu rrent condition and turning-off the switch. The maximum output capacitance can be determined from the following formula, Current Limit Various RSET Values Power Dissipation During normal operation as a switch, the power dissipated in the part will depend upon the level at which the current limit is set. The maximum allowed setting for the current limit is 1.5A and this will result in a typical power dissipation of, If the part goes into current limit the maximum power dissipation will occur when the output is shorted to ground. For the FPF2123 the power dissipation wi ll scale by the Auto-Restart Time, t RESTART, and the Over Current Blanking Time, t BLANK, so that the maximum power dissipated is, RSET 460 ILIM COUT max() ILIM min() tBLANK min()× VIN RSET [Ω] Min. Current Limit [mA] Typ. Current Limit [mA] Max. Current Limit [mA] 309 1120 1490 1860 340 1010 1350 1690 374 920 1230 1540 412 840 1120 1400 453 760 1010 1270 499 690 920 1150 549 630 840 1050 576 600 800 1000 604 570 760 950 732 470 630 790 887 390 520 650 1070 320 430 540 1300 260 350 440 1910 180 240 300 3090 110 150 190 PI LIM()= 2 RON× 1.5() 2 0.125×= 281mW= (2) (1) (3)
11 www.fairchildsemi.com FPF2123-FPF2125 Rev. C4 FPF2123-FPF2125 IntelliMAX™ Advanced Load Management Products This is more power than the package can dissipate, but the thermal shutdown of the part will activate to protect the part from damage due to excessive heating. When using the FPF2124, attention must be given to the manual resetting of the part. Continuously resetting the part when a short on the output is present will cause the temperature of the part to increase. The junction temperature will only be able to increase to the thermal shutdown threshold. Once this temperature has been reached, toggling ON will not turn-on the switch until the junction temperature drops. For the FPF2125, a short on the output will cause the part to operate in a constant current state dissipating a worst case power of, This large amount of power will activate the thermal shutdown and the part will cycle in and out of thermal shutdown so long as the ON pin is active and the short is present. Board Layout For best performance, all traces should be as short as possible. To be most effective, the input and output capacitors should be placed close to the device to minimize the effects that parasitic trace inductances may have on normal and short-circuit operation. Using wide traces for V IN, VOUT and GND will help minimize parasitic electrical effects along with minimizing the case to ambient thermal impedance. 5.5 1.5×= 8.25W= Pm a x() VIN· max() ILIM max()×= (5) (4) Pm a x() tBLANK max()
12 www.fairchildsemi.com FPF2123-FPF2125 Rev. C4 FPF2123-FPF2125 IntelliMAX™ Advanced Load Management Products Dimensional Outline and Pad Layout
13 www.fairchildsemi.com FPF2123-FPF2125 Rev. C4 FPF2123-FPF2125 IntelliMAX™ Advanced Load Management Products TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANG ES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HE REIN; NEITHER DOES IT CONVEY ANY LICE NSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATION S DO NOT EXPAND THE TERMS OF FAIRCH ILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms ACEx™ ActiveArray™ Bottomless™ Build it Now™ CoolFET™ CROSSVOLT™ DOME™ EcoSPARK™ E 2CMOS™ EnSigna™ FACT™ FAST FASTr™ FPS™ FRFET™ FACT Quiet Series™ GlobalOptoisolator™ GTO™ HiSeC™ I 2C™ i-Lo™ ImpliedDisconnect™ IntelliMAX™ ISOPLANAR™ LittleFET™ MICROCOUPLER™ MicroFET™ MicroPak™ MICROWIRE™ MSX™ MSXPro™ OCX™ OCXPro™ OPTOLOGIC OPTOPLANAR™ PACMAN™ POP™ Power247™ PowerEdge™ PowerSaver™ PowerTrench QFET® QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ RapidConnect™ µSerDes™ ScalarPump™ SILENT SWITCHER SMART START™ SPM™ Stealth™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SyncFET™ TCM™ TinyBoost™ TinyBuck™ TinyPWM™ TinyPower™ TinyLogic TINYOPTO™ TruTranslation™ UHC™ UniFET™ UltraFET VCX™ Wire™ Across the board. Around the world.™ The Power Franchise® Programmable Active Droop™ Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datas heet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. No Identification Needed Full Production This datas heet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. Obsolete Not In Production This datasheet c ontains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Rev. I20