FPF1007 FAIRCHILD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 11
Technical content
Features
1.2 to 5.5V Input Voltage Range Typical RON = 30 mΩ @ VIN = 5.5V Typical RON = 40 mΩ @ VIN = 3.3V Fixed Three Different Turn-on Rise-time 10µs/80µs/1ms Low < 10µA @ VIN = 3.3V Quiescent Current Internal ON Pin Pull Down Output Discharge Function ESD Protection above 8000V HBM and 2000V CDM RoHS Compliant
Applications
PDAs Cell Phones GPS Devices MP3 Players Digital Cameras Peripheral Ports Hot Swap Supplies Notebook Computer General Description The FPF1007/8/9 are low RDS P-Channel MOSFET load switches offered in a selection of 10µs, 80µs, and 1ms slew rate turn-on options for transient/in-rush current control. To support trends in mobile applicati on requirements the minimum operating input voltage has been reduced down to 1.2V, the input current leakage has been minimized to extend battery life, and the ESD-protection has been designed to withstand a minimum of 8KV (HBM) and 2KV(CDM). The switch is controlled by an active-high logic input (ON pin) allowing it to interface directly with a low voltage control signal. An internal ON pin pull down resistor protects against an unintentional device turn-on while in the initial state. An On-chip pull-down resistor on the output is enabled when the switch is turned-off and provides a quick and robust discharge of the output load.
Ordering Information
Part Switch RON @ 5.5V [Typ.] Rise Time [Typ.] Output Discharge [Typ.] ON Pin Activity FPF1007 30m Ω, PMOS 10µs 60 Ω Active HI FPF1008 30m Ω, PMOS 80µs 60 Ω Active HI FPF1009 30m Ω, PMOS 1ms 60 Ω Active HI BOTTOM TOP Pin 1
2 www.fairchildsemi.com FPF1007-FPF1009 Rev. B1 FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Typical Application Circuit Functional Block Diagram OFF ON ON IN GND FPF1007-FPF1009 OUT 1.2V~5.5V CIN ≥ 0.1µF RL COUT CONTROL LOGIC VIN ON GND VOUT Output Discharge Turn-ON Slew Rate Controlled Driver ESD Protection FPF1007-FPF1009
3 www.fairchildsemi.com FPF1007-FPF1009 Rev. B1 FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Pin Configuration Pin Description Absolute Maximum Ratings Recommended Operating Range
Electrical Characteristics
4, 5 V OUT Switch Output: Output of the power switch 2, 3 V IN Supply Input: Input to the power switch and the supply voltage for the IC
6 GND Ground
1 ON ON/OFF Control Input
Parameter Min. Max. Unit VIN, VOUT, ON to GND -0.3 6 V Maximum Continuous Switch Current 1.5 A Power Dissipation @ TA = 25°C (Note 1) 1.2 W Storage Junction Temperature -65 150 °C Operating Temperature Range -40 85 °C Thermal Resistance, Junction to Ambient 86 °C/W Electrostatic Discharge Protection HBM 8000 V CDM 2000 V Parameter Min. Max. Unit VIN 1.2 5.5 V Ambient Operating Temperature, TA -40 85 °C Parameter Symbol Conditions Min. Typ. Max. Units Basic Operation Operating Voltage V IN 1.2 5.5 V Quiescent Current I Q IOUT = 0mA, VIN = 3.3V, VON = Enabled 8 µA IOUT = 0mA, VIN = 5.5V, VON = Enabled 15 Off Supply Current I Q(off) V ON = GND, VOUT = OPEN 1 µA Off Switch Current I SD(off) V ON = GND, VOUT = GND 0.1 1 µA VOUT VOUT ON MicroFET 2x2 6L BOTTOM VIEW VIN VIN GND
4 www.fairchildsemi.com FPF1007-FPF1009 Rev. B1 FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Electrical Characteristics Cont. Note 1: Package power dissipation on 1square inch pad, 2 oz. copper board. Parameter Symbol Conditions Min. Typ. Max. Units On-Resistance R ON VIN = 5.5V, IOUT = 200mA, TA = 25°C 30 40 mΩ VIN = 3.3V, IOUT = 200mA, TA = 25°C 40 55 VIN = 1.5V, IOUT = 200mA, TA = 25°C 100 130 VIN = 1.2V, IOUT = 200mA, TA = 25°C 175 250 VIN = 3.3V, IOUT = 200mA, TA = -40°C to +85°C 20 65 Output Pull Down Resistance R PD VIN = 3.3V, VON = 0V, TA = 25°C 60 Ω ON Input Logic Low Voltage V IL VIN = 1.2V to 5.5V 0.4 V ON Input Logic High Voltage V IH VIN = 1.2V to 5.5V 1 V ON Input Leakage (On) V ON = VIN = 5.5V -1 10 µA ON Input Leakage (Off) V ON = GND -1 1 µA Dynamic FPF1007 Turn On t ON VIN = 3.3V, RL = 500Ω, RL_CHIP = 60Ω, COUT = 0.1µF, TA = 25°C 12 µs Rise Time t R 10 µs Turn Off t OFF 40 µs Fall Time t F 15 µs FPF1008 Turn On t ON VIN = 3.3V, RL = 500Ω, RL_CHIP = 60Ω, COUT = 0.1µF, TA = 25°C 125 µs Rise Time t R 80 µs Turn Off t OFF 40 µs Fall Time t F 15 µs FPF1009 Turn On t ON VIN = 3.3V, RL = 500Ω, RL_CHIP = 60Ω, COUT = 0.1µF, TA = 25°C 2m s Rise Time t R 1m s Turn Off t OFF 40 µs Fall Time t F 15 µs
10 www.fairchildsemi.com FPF1007-FPF1009 Rev. B1 FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Dimensional Outline and Pad Layout
11 www.fairchildsemi.com FPF1007-FPF1009 Rev. B1 FPF1007-FPF1009 IntelliMAX™ Advanced Load Products Rev. I33 TRADEMARKS The following are registered and unregistered trademarks and service marks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. * EZSWITCH™ and FlashWriter ® are trademarks of System General Corporation, used under license by Fairchild Semiconducntor. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD’S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or s ystems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms ACEx® Build it Now™ CorePLUS™ CROSSVOLT™ CTL™ Current Transfer Logic™ EcoSPARK EZSWITCH™ * Fairchild® Fairchild Semiconductor® FACT Quiet Series™ FACT FAST® FastvCore™ FlashWriter ® * FPS™ FRFET® Global Power ResourceSM Green FPS™ Green FPS™ e-Series™ GTO™ i-Lo™ IntelliMAX™ ISOPLANAR™ MegaBuck™ MICROCOUPLER™ MicroFET™ MicroPak™ MillerDrive™ Motion-SPM™ OPTOLOGIC OPTOPLANAR® PDP-SPM™ Power220® POWEREDGE® Power-SPM™ PowerTrench Programmable Active Droop™ QFET QS™ QT Optoelectronics™ Quiet Series™ RapidConfigure™ SMART START™ SPM STEALTH™ SuperFET™ SuperSOT™-3 SuperSOT™-6 SuperSOT™-8 SupreMOS™ SyncFET™ The Power Franchise TinyBoost™ TinyBuck™ TinyLogic TINYOPTO™ TinyPower™ TinyPWM™ TinyWire™ µSerDes™ UHC Ultra FRFET™ UniFET™ VCX™ Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only.