FP0115CAC1BC-C2 NKK | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

NKK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Contactless Pushbuttons Series FP01 Distinctive Characteristics Brilliant illumination for highly visible status indication with LEDs and caps in red, green, or amber; subdued illumination for low light requirements with white cap over red, green, or amber LEDs. Photo interrupter, rather than contacts, ensures high reliability and long life of 3 million operations minimum. Rugged construction and smooth actuation allow repeated, rapid actuation force anywhere on cap surface. Snap-in mounting for easy installation. Connector socket with 6 pins for simple connection. Well suited for gaming and vending machines, as well as equipment exposed to corrosive gases used in environments such as chemical or steel manufacturing plants. Actual Size FP01-15

NKK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Contactless Pushbuttons Series FP01 PHOTO TRANSISTOR

1 Single

TYPICAL SWITCH ORDERING EXAMPLE PHOTO INTERRUPTER

5 Unshaded (Shaded)

(Momentary Operating Function) DESCRIPTION FOR TYPICAL ORDERING EXAMPLE FP0115CAC1FF HOUSING A Black No Connector Plug Round, Black Housing Green Actuator with Green LED Single Photo Transistor with Normally Unshaded Photo Interrupter LEDS C Red D Amber F Green ACTUATOR COLORS B White C Red D Amber F Green FP01 SHAPE C Round RECEPTACLE C1 6-pin Socket See Plug Options. PLUG OPTIONS C2 Assembled Connector Plug with Wire Leads C3 Unassembled Connector Plug and Pins No Code No Connector Plug Contact factory for custom options. 1 5 C A C1 F F

NKK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Contactless Pushbuttons Series FP01 Actuator Up Actuator Down Status of Photo Interrupter: Unshaded Shaded Collector Current I C: 0.8mA minimum 10µA maximum Status of Photo Transistor: On Off Output Condition of Photo Transistor: IF = 20mA & VCE = 5V SWITCH SPECIFICATIONS Total Travel: .079” (2.0mm) Operating Force: 0.75 N (.169 lbf) Mechanical Life: 3,000,000 operations minimum Operating Temperature Range: –25°C through +50°C (–13°F through +122°F) MECHANICAL SPECIFICATIONS Actuator: Polyacetal Housing: Polyamide MATERIALS Actuator Position Photo Interrupter Schematics Model Normal Down Unshaded Shaded LED connector pins are 5 & 6; interrupter connector pins are 3-4 & 1-2. FP0115 Single Photo Transistor When shaded, the photo transistor momentarily activates electrical function which signals the external device to change its state. ACTUATOR & INTERRUPTER HOUSING SHAPE & COLOR INTERNAL RECEPTACLE C Round Shape Black HousingA Internal male connector socket ReceptacleC1 6 5 4 3 21 1 5 6 5 4 3 2 1 Normally Unshaded with Momentary Shaded status

NKK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Contactless Pushbuttons Series FP01 PHOTO INTERRUPTER SPECIFICATIONS Electrical & Optical Characteristics Typical Maximum Condition Input Forward Voltage VF: 1.3V 1.6V IF = 50mA Reverse Current I R: 10µA FR = 5V Transmission Collector-Emitter Saturation Voltage V CE sat: 0.4V IF = 20mA & IC = 0.1mA Absolute Maximum Ratings Input LED Output Photo Transistor Forward Current I F: 50mA Collector-Emitter Voltage VCEO: 30V Reverse Voltage VR: 5V Emitter-Collector Voltage VECO: 4.5V Power Dissipation P D: 80mW Collector Current IC: 30mA Collector Dissipation PC: 80mW Circuit Design Considerations Output of the infrared LED in the photo interrupter decreases approximately 50% after 100,000 hours. Recommended load resistance (RL) is 40k ~ 120kΩ for the illustrated circuit. (Temperature @ 25°C) 180Ω GND VOUT RL V = 5VCC Threshold Voltage VHI: 3.8V VLO: 1.0V R = E – VF IF Where: R E VF IF = Resistor Value (Ohms) = Source Voltage (V) = Forward Voltage (V) = Forward Current (A) Color Red Amber Green Forward Peak Current IFM 30mA 25mA 25mA Continuous Forward Current IF 20mA 20mA 20mA Forward Voltage VF 1.85V 2.0V 2.25V Reverse Peak Voltage VRM 5V 5V 5V Current Reduction Rate Above 25°C ∆IF 0.38mA /°C 0.28mA /°C 0.40mA /°C Ambient Temperature Range –25° ~ +50°C C LED COLORS & SPECIFICATIONS Single Element LED VF I FR + E Anode Cathode D F LEDs are an integral part of the switch and not available sepa - rately. The electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the rated volt- age, a ballast resistor is required. ACTUATOR COLORS B White C Red D Amber F Green

NKK Switches • email: sales@nkkswitches.com • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Contactless Pushbuttons Series FP01 (1.5) .059 (5.0) .197 (5.3) .209 (21.4) .843 (2.3) .091 NKK P/N This Side TYPICAL SWITCH DIMENSIONS FP0115CAC1FF (19.6) Dia .772 (26.0) Dia 1.024 6 5 4 3 21 (22.8) Dia .898 Terminal Connector Detail Pin 1 (22.9) Dia .902 (25.1) .988 (1.1)R Typ .043 Recommended Panel Thickness Range: .098” ~ .197” (2.5mm ~ 5.0mm) AT022 Unassembled Connector Plug and Pins EXTERNAL PLUG OPTIONS C2 AT021 Assembled Connector Plug with Wire Leads C3 No Code No Connector Plug Recommended connector plug for assembly: JST model number ZHR-6 Recommended crimp connector pins: JST model SZH-002T-P0.5 for 28-26AWG wire leads or SZH-003T-P0.5 for 32-28AWG wire leads. 1 connector plug and 8 crimp connector pins only (no wire leads provided). Matching wire leads: 28-26AWG Connector plug body: JST model ZHR-6 Crimp connector pins: JST model SZH-002T-P0.5 Wire leads: 28-26AWG; 12-inch, unstripped; Blue for Pin 1 LEGENDS Shaded area is printable area. Easily create and submit your own legends using our new on-line Legend Maker. Visit www.nkkswitches.com For other legend support options, customers may either contact the factory or utilize the general information and basic specifications presented below. Recommended Methods: Pad Print or Laser Etch on cap. Epoxy based ink is recommended. Suggested Printable Area for FP01 Cap LM (16.56) Dia .475 (19.6) Dia .772 (1.52) Typ .060 ALER T