FME270-461

FME270-461_10 INTERPOINT | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 11

Technical content

Features

attenuation to 50 dB at 500 kHz Operating temperature -55° to +125°C• Nominal 270 V input, 0 to 400 V operation• Transient rating to 500 V for 100 ms• Up to 1.5 A throughput current• Compliant to • MIL-STD-461C, CE03 - Crane Aerospace & Electronics Power Solutions FMe270-461 eMi input Filters Crane Aerospace & Electronics Electronics Group (Interpoint Brand) PO Box 97005 • Redmond WA 98073-9705 425.882.3100 • power@crane-eg.com www.interpoint.com Page 1 of 11 FME270 Rev B - 20100226 270 Volt input – 1.5 aMp

Angled corner and cover marking indicate pin one for cases U and V. Cover marking indicates pin one for cases W, Y and Z. TOP VIEW All FME270 models/cases1 Outline shown is case U, pin out is the same for all cases. See cases U, V, W, Y, and Z for dimensions. Notes 1. All pins must be connected. 2. The baseplate is the only case ground connection and should directly contact chassis ground. FIguRe 3: pIn Out pin 1 Designation 1, 2, 3 Positive Input 4, 5, 6 Input Common 7, 8, 9 Output Common 10, 11, 12 Positive Output — Case Ground 2 Crane Aerospace & Electronics Power Solutions www.interpoint.com Page 3 of 11 FMe270-461 eMi input Filters 270 Volt input – 1.5 aMp FME270 Rev B - 20100226

On the lines b e lOw, enter On e selectiOn f rOm under each categOry tO determine the mOd e l number. category Base MoDel anD input Voltage Mil-stD-461 reFerence case/leaD option 1 screening 2 selection “FMe270” is the only available selection “-461” is the only available selection u (leave blank) V standard (leave blank) W es y Z Notes: 1. Case U is the standard, side-leaded, flanged case. Leave the option blank for case U. Refer to the case drawings on pages 7 - 10 for other case options. 2. Leave blank for standard screening. Use “ES” for “ES” screening. See page 11 for more information. MoDel nuMBering key FME 270 - 461 V / ES Base Model Input Voltage MIL-STD-461 Reference Screening Case/Lead Option* (Standard screening has no designator in this position.) *Case/Lead Option: See cases U, V, W, Y, and Z for drawings and dimensions. Crane Aerospace & Electronics Power Solutions www.interpoint.com Page 4 of 11 FMe270-461 eMi input Filters 270 Volt input – 1.5 aMp FME270 Rev B - 20100226

Electrical Characteristics: 25°C TC , nominal Vin, unless otherwise specified. Note 1. guaranteed by design, not tested. MODEL FME270-461 paRaMeteR cOndItIOns MIN TYP MAX unIts Input vOltage cOntInuOus 0 270 400 VDC tRansIent 100 ms 1 -500 — 500 V nOIse ReJectIOn 500 khz 40 50 — dB

1 Mhz 45 55 —

dc ResIstance (Rdc) at MaXIMuM cuRRent 1 tc = 125°c — — 3.2 capacItance 1 anY pIn tO case — 60,000 pF Output vOltage steadY state VOUT = VIN - IIN (RDC) VDC Output cuRRent steadY state — — 1.5 A pOWeR dIssIpatIOn at MaXIMuM cuRRent 1 tc = 125°c 1 — — 7.2 Crane Aerospace & Electronics Power Solutions www.interpoint.com Page 5 of 11 FMe270-461 eMi input Filters 270 Volt input – 1.5 aMp FME270 Rev B - 20100226

indicates pin one. 0.000 0.050 (1.27) 0.000 0.120 (3.05) 0.250 (6.35) 0.450 (11.43) 0.650 (16.51) 0.850 (21.59) 1.050 (26.67) 1.250 (31.75) 1.380 (35.05) 1.505 (38.23) max. 0.000 0.120 (3.05) 0.250 (6.35) 2.750 (69.85) 2.880 (73.15) 3.005 (76.33) max. 0.128 dia (3.25). 0.040 dia (1.02) 0.23 (5.8) Pin Length 0.400 (10.16) max. 0.220 (5.59 TOP VIEW CASE U* Flanged case, short-leaded Seam Seal *Does not require designator in Case Option position of model number. Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold, compression glass seal Seal Hole: 0.100 ±0.002 (2.54 ±0.05) Case U, Rev E, 20100401 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2010 Interpoint Corp. All rights reserved. FIguRe 4: case u - FMe270-461 Crane Aerospace & Electronics Power Solutions www.interpoint.com Page 6 of 11 FMe270-461 eMi input Filters – cases 270 Volt input – 1.5 aMp FME270 Rev B - 20100226

0.000 0.220 (5.59) 0.050 (1.27) 0.400 (10.16) max ref: 0.250 ±0.050 (6.35 ±1.27) ref: 0.225 (5.72 3.45 (87.6) Reference (lead center to lead center) 0.000 0.120 (3.05) 0.250 (6.35) 0.450 (11.43) 0.650 (16.51) 0.850 (21.59) 1.050 (26.67) 1.250 (31.75) 1.380 (35.05) 0.000 0.120 (3.05) 0.250 ±0.010 (6.35 ±0.3) 2.750 (69.85) 2.880 (73.15) 0.128 dia (3.25) 0.040 dia (1.02) TOP VIEW CASE V* Flanged case, down leaded *Designator "V" required in Case Option position of model number. Maximum dimensions: 3.005 x 1.505 (76.33 x 38.23 mm) Angled corner indicates pin one. 3.005 (76.33) max Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold, compresssion glas seal Seal Hole: 0.120 ±0.002 (3.05 ±0.05) Case V, Rev E, 20100106 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2009 Interpoint Corp. All rights reserved. Seam Seal FIguRe 5: case v - FMe270-461v Crane Aerospace & Electronics Power Solutions www.interpoint.com Page 7 of 11 FMe270-461 eMi input Filters – cases 270 Volt input – 1.5 aMp FME270 Rev B - 20100226

0.040 dia (1.02) 0.250 (6.35) Typ. 0.125 (3.18) 0.375 (9.53) 0.575 (14.61) 0.775 (19.69) 0.975 (24.77) 1.175 (29.85 1.375 (34.93) 1.625 (41.28) 2.125 (53.98) 0.375 (9.53) 0.140 dia (3.56)0.000 1.750 (44.45) 0.000 0.250 (6.35) Typ. 1.450 (36.83) 0.300 (7.62) 1.750 (44.45) 2.000 (50.80) TOP VIEW CASE W* Tabbed case, up-leaded 0.000 0.220 (5.59) 0.050 (1.27) 0.400 (10.16) max. 0.000 0.220 (5.59) 0.400 (10.16) max. 0.84 ±0.05 (21.3 ±1.3) 0.84 ±0.05 (21.3 ±1.3) 0.150 (3.81) Lead Detail 2.80 (71.1) Reference (lead center to lead center) *Designator "W" required in Case Option position of model number. Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold, compresssion glass seal Seal Hole: 0.120 ±0.002 (3.05 ±0.05) Case W, Rev E, 20100401 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2010 Interpoint Corp. All rights reserved. Seam Seal FIguRe 6: case W - FMe270-461W Crane Aerospace & Electronics Power Solutions www.interpoint.com Page 8 of 11 FMe270-461 eMi input Filters – cases 270 Volt input – 1.5 aMp FME270 Rev B - 20100226

0.250 (6.35) Typ. 0.125 (3.18) 0.375 (9.53) 0.575 (14.61) 0.775 (19.69) 0.975 (24.77) 1.175 (29.85 1.375 (34.93) 1.625 (41.28) 2.125 (53.98) 0.375 (9.53) 0.140 dia (3.56)0.000 1.750 (44.45) 0.000 0.250 (6.35) Typ. 1.450 (36.83) 0.300 (7.62) 1.750 (44.45) 2.000 (50.80) 0.000 0.220 (5.59) 0.050 (1.27) 0.400 (10.16) max. TOP VIEW CASE Y* Tabbed case, straight-leaded 0.000 0.220 (5.59) 0.400 (10.16) max. 0.30 ±0.05 (7.6 ±1.3) Lead Detail Pin Length 0.30 ±0.05 (7.6 ±1.3) 3.10 (78.7) Reference 0.040 dia (1.02) *Designator “Y” required in Case Option position of model number. Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold, compresssion glass seal Seal Hole: 0.120 ±0.002 (3.05 ±0.05) Case Y, Rev E, 20100401 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2010 Interpoint Corp. All rights reserved. FIguRe 7: case Y - FMe270-461Y Crane Aerospace & Electronics Power Solutions www.interpoint.com Page 9 of 11 FMe270-461 eMi input Filters – cases 270 Volt input – 1.5 aMp FME270 Rev B - 20100226

0.250 (6.35) Typ. 0.125 (3.18) 0.375 (9.53) 0.575 (14.61) 0.775 (19.69) 0.975 (24.77) 1.175 (29.85 1.375 (34.93) 1.625 (41.28) 2.125 (53.98) 0.375 (9.53) 0.140 dia (3.56)0.000 1.750 (44.45) 0.000 0.250 (6.35) Typ. 1.450 (36.83) 0.300 (7.62) 1.750 (44.45) 2.000 (50.80) TOP VIEW CASE Z* Tabbed case, down-leaded *Designator “Z” required in Case Option position of model number. 0.000 0.220 (5.59) 0.050 (1.27) 0.400 (10.16) max. 0.000 0.220 (5.59) 0.400 (10.16) max. 0.36 ±0.05 (9.1±0.13) 0.150 (3.81) Lead Detail 2.80 (71.1) Reference (lead center to lead center) 0.36 ±0.05 (9.1±0.13) 0.040 dia (1.02)1 Case dimensions in inches (mm) Tolerance ±0.005 (0.13) for three decimal places ±0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300°C for 10 seconds per pin. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold, compresssion glass seal Seal Hole: 0.120 ±0.002 (3.05 ±0.05) Case Z, Rev E, 20100401 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Copyright © 1999-2010 Interpoint Corp. All rights reserved. Seam Seal FIguRe 8: case z - FMe270-461z Crane Aerospace & Electronics Power Solutions www.interpoint.com Page 10 of 11 FMe270-461 eMi input Filters – cases 270 Volt input – 1.5 aMp FME270 Rev B - 20100226

ST A N D A R D A N D /ES (N O N-QML) PR O D U C T S EN V I R O N M E N T A L SC R E E N I N G 1 test perFOrmed standard nOn-Qml2 /es nOn-Qml2 Pre-cap Inspection Method 2017, 2032 yes yes Temperature Cycle (10 times) Method 1010, Cond. B, -55°C to +125°C, ambient no yes Constant Acceleration Method 2001, 500 g no yes Burn-in Method 1015 3 96 hours no yes Final Electrical Test MIL-PRF-38534, Group A Subgroups 1 and 4: +25°C case yes yes Hermeticity Test Fine Leak, Method 1014, Cond. A Gross Leak, Method 1014, Cond. C Gross Leak, Dip (1 x 10 -3) no no yes yes yes no Final visual inspection Method 2009 yes yes Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534. Notes: 1. refers to products that do not offer QMl screening. 2. Standard and /ES, non-QML products, do not meet all of the requirements of MIL-PRF-38534. 3. Burn-in designed to bring the case temperature to the maximum case temperature of the product. Refer to the specific product information for the maximum case temperature. Crane Aerospace & Electronics Power Solutions FME270-461 EMI Input Filters FME270 Rev B - 20100226. This revision supersedes all previous releases. All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. Page 11 of 11 FMe270-461 eMi input Filters 270 Volt input – 1.5 aMp