FMAM4077 FAIRVIEW | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 7

Technical content

Copyright © 2020 The PE15A4077 is a 1 Watt coaxial packaged power amplifier operating across a frequency range from 5 GHz to 6 GHz. Impressive typical performance includes 31 dB small signal gain, 7 dB noise figure, +32 dBm P3dB, +34 dBm Psat, and an output 3rd order intercept point of +42 dBm. Maximum RF input power is +23 dBm. This exceptional technical performance is achieved through the use of a hybrid MIC design and advanced GaAs devices. The amplifier supports an integrated heatsink for optimum thermal dissipation. Addtional features include reverse DC protection and internal voltage regulation with a DC voltage range from +9V to +15V (+12V nominal) with a DC current of 920 mA (@Pout = +30 dBm), and 1300 mA (@Psat = +33 dBm). The operational temperature range is -40°C to +85°C. The rugged pacakge assemblyh supports SMA female connectors and RFI and Ground pins. And for highly reliable operation, the model is guaranteed to meet environmental test conditions for Humidity, Shock, Vibration, and Altitude. Electrical Specifications (TA = +25°C, DC Voltage = +12Volts, DC Current = 920mA) Description Min Typ Max Unit Frequency Range 5 6 GHz Small Signal Gain* 28 31 dB Gain Flatness ±1.5 ±2 dB Input Power (CW) +23 dBm Pout at Sat.* +33 +34 dBm Output 3rd Intercept Point* +40 +42 dBm Output Power (3dB Compression Point)* 30 32 dBm Reverse Isolation -45 -50 dB Noise Figure 7 9 dB Impedance (Input) 50 Ohms Impedance (Output) 50 Ohms Input VSWR 2:1 2.5:1 Output VSWR 1.5:1 2:1 Operating DC Voltage +9 +12 +15 Volts Operating DC Current** 920 1.2 mA Operating Current @Pout=+33 dBm 1.3 2 A Quiescent Current (No Input) 370 450 mA *Frequency = 5500 MHz **@ Pout = +30 dBm Absolute Maximum Rating Parameter Absolute Maximum RF Input Power +23dBm Supply Voltage +18V . Operating Temperature -40 °C to +85 °C Storage Temperature -55 °C to +125 °C . .

1 Watt P3dB, 5 GHz to 6 GHz, Medium Power GaAs

Amplifier with Heatsink, 31 dB Gain, 42 dBm IP3 and SMA FMAM4077 DATA SHEET Fairview Microwave 301 Leora Ln., Suite 100 Lewisville, TX 75056 Tel: 1-800-715-4396 / (972) 649-6678 Fax: (972) 649-6689 www.fairviewmicrowave.com sales@fairviewmicrowave.com Features:

  • 1 Watt Power Amplifier
  • 5 GHz to 6 GHz
  • Small Signal Gain 31 dB typ
  • 7 dB Noise Figure
  • Output P3dB +32 dBm/ Output Psat +34 dBm
  • Output IP3 +42 dBm
  • Max RF Input Power +23 dBm
  • Integrated Heatsink
  • Reverse DC Protection
  • Internal Voltage Regulation
  • DC Voltage +12Vdc
  • DC Current 1300 mA
  • Operational Temperature Range -40°C to +85°C
  • SMA Female Connectors
  • 50 Ohm Design
  • Rugged Design meets MIL- STD-202 Test Conditions Applications:
  • Aerospace & Defense
  • Test & Measurement
  • Microwave Radio Systems
  • Military & Commercial Communication Systems
  • Research & Development
  • SATCOM
  • Wireless Communications

Length 3.75 in [95.25 mm] Width 2 in [50.8 mm] Height 1.813 in [46.05 mm] Weight 0.56 lbs [254.01 g] Input Connector SMA F emale Output Connector SMA F emale Environmental Specifications Temperature Operating Range -40 to +85 deg C Storage Range -55 to +105 deg C Humidity MIL -STD-202, Method 103B, Condition B Shock MIL -STD-202F, Method 213B, Condition B Vibration MIL -STD-202F, Method 204D, Condition B Altitude MIL -STD-202F, Method 105C, Condition B Compliance Certifications (see product page for current document) Plotted and Other Data Notes:

  • Values at 25 °C, sea level 301 Leora Ln., Suite 100, Lewisville, TX 75056 | Tel: 1-800-715-4396 / (972) 649-6678 / Fax: (972) 649-6689 REV 1 Page 2 of 7 FMAM4077 DATA SHEET

Amplifier Power-up Precautions 1.) Confirm that proper ESD precautions and controls are always in place before handling any Amplifier module. 2.) Confirm adequate thermal management is in place to effectively dissipate heat away from the Amplifier package. The Amplifier operational baseplate temperature must be within the operational temperature range stated in the Amplifier datasheet. Depending on the design and thermal requirements, using a heatsink with cooling fan is always recommended for safe reliable operation. A heat sink without a cooling fan may also be used. Damage caused from overheating will void the warranty. 3.) Confirm adequate system grounding is established. The DC power supply and Amplifier must have a common ground in order to operate properly. 4.) Power Amplifiers may require additional DC Current when initially powered- up. Depending on the design, the input current draw could range from an additional 10% to 100% above the maximum rated DC current of the Amplifier. This varies based on product part number. 5.) Confirm the DC power supply, if limited, is set to allow for additional start-up current that’s rated for the Power Amplifier. 6.) Confirm the system is designed and calibrated for 50 ohms. Any impedance mismatch may cause performance issues. 7.) Perform a CALIBRATION (if required) with the loads before connecting the Amplifier to the Network Analyzer to ensure proper performance. 8.) Use a fixed attenuator between the signal source and input port of the Amplifier to optimize the input VSWR match. 9.) Confirm the input power level at the input port of the amplifier does not exceed the maximum rated limit for input power (as stated in the Amplifier datasheet). Pin for Small Signal Gain = P1dB-SSG-10 dB Pin for P1dB = P1dB-SSG+1 dB 10.) Confirm the Network Analyzer is always connected to the Amplifier first before DC power is applied to the Amplifier. 11.) As long as the input and output ports of the amplifier are connected to a 50Ohm load and RF signal power is applied, the Amplifier can be powered up with DC voltage. 12.) Confirm the Amplifier output load is matched for a 50 Ohm impedance and will not exceed the maximum rated VSWR or Return Loss limit for the Amplifier. Exceeding the maximum rated VSWR or Return Loss limit will result in reflected signal power that could damage the Amplifier and void the warranty. 13.) Power Amplifier connected to an Antenna for signal transmission - It’s strongly recommended to use a high power fixed attenuator pad or an Isolator between the output port of the Amplifier and input port to the antenna. Any reflected signal power due to impedance mismatch will likely damage the Amplifier and void the warranty. 14.) The attenuator or isolator used at the output port of the Amplifier must be rated to handle the output power level and operational frequency band of the amplifier. Typical Performance Data 301 Leora Ln., Suite 100, Lewisville, TX 75056 | Tel: 1-800-715-4396 / (972) 649-6678 / Fax: (972) 649-6689 REV 1 Page 3 of 7 FMAM4077 DATA SHEET

301 Leora Ln., Suite 100, Lewisville, TX 75056 | Tel: 1-800-715-4396 / (972) 649-6678 / Fax: (972) 649-6689 REV 1 Page 4 of 7 20.0 24.0 28.0 32.0 36.0 40.0 5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000 dB MHz Gain -100.0 -82.0 -64.0 -46.0 -28.0 -10.0 5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000 dB MHz Reverse Isolation FMAM4077 DATA SHEET

301 Leora Ln., Suite 100, Lewisville, TX 75056 | Tel: 1-800-715-4396 / (972) 649-6678 / Fax: (972) 649-6689 REV 1 Page 5 of 7 -60.0 -48.0 -36.0 -24.0 -12.0 0.0 5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000 dB MHz I/O Return Loss Input Output 2.0 3.6 5.2 6.8 8.4 10.0 5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000 dB MHz Noise Figure FMAM4077 DATA SHEET

301 Leora Ln., Suite 100, Lewisville, TX 75056 | Tel: 1-800-715-4396 / (972) 649-6678 / Fax: (972) 649-6689 REV 1 Page 6 of 7 FMAM4077 DATA SHEET 20.0 24.0 28.0 32.0 36.0 40.0 5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000 dBm MHz Output Power @P3dB 20.0 28.0 36.0 44.0 52.0 60.0 5000 5100 5200 5300 5400 5500 5600 5700 5800 5900 6000 dBm MHz Output IP3 1 Watt P3dB, 5 GHz to 6 GHz, Medium Power GaAs Amplifier with Heatsink, 31 dB Gain, 42 dBm IP3 and SMA from Fairview Microwave is in-stock and available to ship same-day. All of our RF/microwave products are available off-the-shelf from our ISO 9001:2008 certified facilities in Lewisville, Texas. Fairview Microwave is RF on-demand. For additional information on this product, please click the following link: 1 Watt P3dB, 5 GHz to 6 GHz, Medium Power GaAs Amplifier with Heatsink, 25 dB Gain, 42 dBm IP3 and SMA FMAM4077 URL:

301 Leora Ln., Suite 100, Lewisville, TX 75056 | Tel: 1-800-715-4396 / (972) 649-6678 / Fax: (972) 649-6689 REV 1 Page 7 of 7 .40 10.2 1.00 25.4 2.00 50.80 3,75 102.12 3,400 92.52 1.750 44.45 1.81 46.0 .38 9.5 1.00 25.4 4X .150 3.81 MOUNTING HOLE Website: www.FairviewMicrowave.com 3FKR5 TOLERANCES: .XX = ±.02 [0.5] .X = ±.2 [5] ± 1/32 FRACTIONS ANGLES ± 1° CABLE LENGTH TOLERANCES: UNLESS OTHERWISE SPECIFIED LEADING DIMENSIONS ARE INCHES DIMENSIONS IN [ ] ARE MILLIMETERS ALL DIMENSIONS ARE FOR REFERENCE ONLY AND SUBJECT TO CHANGE WITHOUT NOTICE. UN-DIMENSIONED/NON-CRITICAL FEATURES MAY VARY IN SIZE AND LOCATION COLORS MAY VARY 2X SMA FEMALE CONNECTOR VDC=+12V 4077 XXXXXXXXXXXX REVISION ZONE REV. DESCRIPTION DATE CHANGED BY APPROVED BY A INITIAL RELEASE 07/17/2023 BPUCHASKI TGALLA ITEM NO. 1 1 REVCAGE CODE SIZE A OF DRAWN BY FMAM4077 A T-Rev.D3

DESCRIPTION

1 Watt P3dB, 5 GHz to 6 GHz, Medium Power GaAs Amplifier with

Heatsink, 25 dB Gain, 42 dBm IP3 and SMA BPUCHASKI THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF INFINITE ELECTRONICS, INC. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF INFINITE ELECTRONICS, INC. IS PROHIBITED. THESE COMMODITIES, TECHNOLOGY OR SOFTWARE WERE EXPORTED FROM THE UNITED STATES IN ACCORDANCE WITH THE EXPORT ADMINISTRATION REGULATIONS. DIVERSION CONTRARY TO U.S. LAW PROHIBITED. SHEETSCALE NONE INTERPRET ALL DIMENSIONS AND TOLERANCES PER ASME Y14.5 A A B B C C D D E E F F FMAM4077 DATA SHEET Amplifier with Heatsink, 31 dB Gain, 42 dBm IP3 and SMA