FMAM1077 FAIRVIEW | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 7

Technical content

Copyright © 2020 The FMAM1077 is an WR28 Waveguide Low Noise Amplifier that operates in the 27 GHz to 40 GHz millimeter wave frequency band. The module utilizes GaAs semiconductor and chip-and-wire technology in the manufacturing process that ensures state-of-the-art performance. Impressive typical performance includes 3 dB noise figure, 35 dB gain, 2.0:1 VSWR, 10 dBm output P1dB, 12 dBm Output Psat, +20 dBm output IP3. Additional typical performance includes 45 dB small signal gain, 1.8:1 VSWR, output P1dB of +22 dBm, output Psat of and output IP3 of +31 dBm. The 50 ohm design has an operational temperature range is -45°C to +85°C and the bias voltage requirement is +12Vdc with 110 mA of DC current. The rugged aluminum Mil Grade package has an epoxy sealed cover and UG599/U waveguide flanges. The model is designed to meet a series of environmental conditions including Altitude, Vibration, Humidity, and Shock. Electrical Specifications (TA = +25°C , DC Voltage = +12Vdc , DC Current = 110mA) . Description Min Typ Max Unit Frequency Range 27 40 GHz Small Signal Gain 30 35 dB Gain Flatness ±3 dB Gain Variance at OTR* 2 dB Output at 1 dB Compression Point +6 +10 dBm Saturated Output Power (Psat) +12 dBm Output 3rd Intercept Point +20 dBm Noise Figure 3 4.5 dB Input VSWR 2:1 Output VSWR 2:1 Reverse Isolation -50 dB Operating DC Voltage +12 +15 V olts Operating DC Current 110 150 mA Operating Temperature Range -45 +85 °C . . *OTR= Base Plate Operating Temperature Range Electrical Procedures Biasing Up Procedure Power OFF Procedure Step 1 Connect Ground Pin Step 1 Turn off +12 V Biasing Step 2 Connect Input and Output Step 2 Remove RF Connection Step 3 Connect +12 V Biasing Step 3 Remove Ground FMAM1077 DATA SHEET 35 dB Gain Waveguide Low Noise Amplifier Operat- ing from 27 GHz to 40 GHz with 3 dB NF, 12 dBm Psat and WR28 Fairview Microwave 301 Leora Ln., Suite 100 Lewisville, TX 75056 Tel: 1-800-715-4396 / (972) 649-6678 Fax: (972) 649-6689 www.fairviewmicrowave.com sales@fairviewmicrowave.com Features:

  • WR28 Waveguide Low Noise Amplifier
  • GaAs Semiconductor Technology
  • Frequency Range 27 to 40 GHz
  • Noise Figure 3 dB
  • Small Signal Gain 35 dB
  • VSWR 2:0:1
  • Ouput P1dB +10 dBm
  • Outpu Psat +12 dBm
  • Output IP3 +20 dBm
  • Isolation -50 dB
  • DC Voltage +12 Vdc
  • DC Current 110 mA
  • 50 Ohm Design
  • Rugged Mil Grade Aluminum Package Design
  • UG599/U Waveguide Flanges
  • -45oC to +85oC Operating Temperature Applications:
  • Aerospace & Defense
  • Microwave Radio
  • Military & Commercial Communication
  • VSAT
  • SATCOM
  • Test & Measurement
  • Wireless Infrastructure
  • Fiber Optics

Operating Voltage +15 Volts RF Input Power @(50 Ω) -18 dBm ESD Sensitive Material, Transport material in Approved ESD bags. Handle only in approved ESD Workstation. Mechanical Specifications Size Length 1.79 in [45.47 mm] Width 2.48 in [62.99 mm] Height 0.75 in [19.05 mm] Weight 0.8 lbs [362.87 g] Input Connector WR28 Output Connector WR28 Environmental Specifications Temperature Operating Range -45 to +85 deg C Storage Range -55 to +125 deg C Humidity 100% RH at 35°C, 95% RH at 40°C Shock 20G for 11 ms half sine w ave, 3 axis both directions Vibration 25g RMS (15 degrees 2KHz) endur ance, 1 hour per axis Altitude 30,000 ft. (Epo xy Sealed Controlled Environment) Compliance Certifications (see product page for current document) Plotted and Other Data Notes:

  • Values at 25 °C, sea level 301 Leora Ln., Suite 100, Lewisville, TX 75056 | Tel: 1-800-715-4396 / (972) 649-6678 / Fax: (972) 649-6689 REV 1 Page 2 of 7 FMAM1077 DATA SHEET

Amplifier Power-up Precautions 1.) Confirm that proper ESD precautions and controls are always in place before handling any Amplifier module. 2.) Confirm adequate thermal management is in place to effectively dissipate heat away from the Amplifier package. The Amplifier operational baseplate temperature must be within the operational temperature range stated in the Amplifier datasheet. Depending on the design and thermal requirements, using a heatsink with cooling fan is always recommended for safe reliable operation. A heat sink without a cooling fan may also be used. Damage caused from overheating will void the warranty. 3.) Confirm adequate system grounding is established. The DC power supply and Amplifier must have a common ground in order to operate properly. 4.) Power Amplifiers may require additional DC Current when initially powered- up. Depending on the design, the input current draw could range from an additional 10% to 100% above the maximum rated DC current of the Amplifier. This varies based on product part number. 5.) Confirm the DC power supply, if limited, is set to allow for additional start-up current that’s rated for the Power Amplifier. 6.) Confirm the system is designed and calibrated for 50 ohms. Any impedance mismatch may cause performance issues. 7.) Perform a CALIBRATION (if required) with the loads before connecting the Amplifier to the Network Analyzer to ensure proper performance. 8.) Use a fixed attenuator between the signal source and input port of the Amplifier to optimize the input VSWR match. 9.) Confirm the input power level at the input port of the amplifier does not exceed the maximum rated limit for input power (as stated in the Amplifier datasheet). Pin for Small Signal Gain = P1dB-SSG-10 dB Pin for P1dB = P1dB-SSG+1 dB 10.) Confirm the Network Analyzer is always connected to the Amplifier first before DC power is applied to the Amplifier. 11.) As long as the input and output ports of the amplifier are connected to a 50Ohm load and RF signal power is applied, the Amplifier can be powered up with DC voltage. 12.) Confirm the Amplifier output load is matched for a 50 Ohm impedance and will not exceed the maximum rated VSWR or Return Loss limit for the Amplifier. Exceeding the maximum rated VSWR or Return Loss limit will result in reflected signal power that could damage the Amplifier and void the warranty. 13.) Power Amplifier connected to an Antenna for signal transmission - It’s strongly recommended to use a high power fixed attenuator pad or an Isolator between the output port of the Amplifier and input port to the antenna. Any reflected signal power due to impedance mismatch will likely damage the Amplifier and void the warranty. 14.) The attenuator or isolator used at the output port of the Amplifier must be rated to handle the output power level and operational frequency band of the amplifier. 301 Leora Ln., Suite 100, Lewisville, TX 75056 | Tel: 1-800-715-4396 / (972) 649-6678 / Fax: (972) 649-6689 REV 1 Page 3 of 7 FMAM1077 DATA SHEET

301 Leora Ln., Suite 100, Lewisville, TX 75056 | Tel: 1-800-715-4396 / (972) 649-6678 / Fax: (972) 649-6689 REV 1 Page 4 of 7 Typical Performance Data FMAM1077 DATA SHEET

301 Leora Ln., Suite 100, Lewisville, TX 75056 | Tel: 1-800-715-4396 / (972) 649-6678 / Fax: (972) 649-6689 REV 1 Page 5 of 7 FMAM1077 DATA SHEET

301 Leora Ln., Suite 100, Lewisville, TX 75056 | Tel: 1-800-715-4396 / (972) 649-6678 / Fax: (972) 649-6689 REV 1 Page 6 of 7 35 dB Gain Waveguide Low Noise Amplifier Operating from 27 GHz to 40 GHz with 3 dB NF, 12 dBm Psat and WR28 from Fairview Microwave is in-stock and available to ship same-day. All of our RF/microwave products are available off-the-shelf from our ISO 9001:2008 certified facilities in Lewisville, Texas. Fairview Microwave is RF on-demand. For additional information on this product, please click the following link: 35 dB Gain Waveguide Low Noise Amplifier Operating from 27 GHz to 40 GHz with 3 dB NF, 12 dBm Psat and WR28 FMAM1077 URL: https://www.fairviewmicrowave.com/3db-nf-low-noise-amplifier-35db-fmam1077-p.aspx FMAM1077 DATA SHEET

301 Leora Ln., Suite 100, Lewisville, TX 75056 | Tel: 1-800-715-4396 / (972) 649-6678 / Fax: (972) 649-6689 REV 1 Page 7 of 7 .140 3.56 .530 13.46 .500 12.70 .280 7.11 .750 19.05 SQ FLANGE DETAIL WR-28 4X 4-40 UNC-2B THRU HOLES 2.48 63.0 1.18 30.0 1.02 26.0 1.42 36.0 1.57 40.0 .67 17.0 TYP .079 2.00 .079 2.00 4X M2.5 TAP THRU HOLES NOTES: LABEL PER ILS-100-02. FOR INTERNAL REFERENCE ONLY.1. LABEL LOCATION FOR REFERENCE ONLY. LABEL PER ILS-100-02 (SEE NOTE 1) 1.60 40.5 .43 11.0 .67 17.0 .47 12.0 .24 6.0 .32 8.2 WR-28 UG-599/U SQUARE FLANGE TYP REVISIONS REV. DESCRIPTION DATE APPROVED A INITIAL RELEASE 7/16/2020 T.GALLA TITLE THE INFORMATION AND DESIGN IN THIS DOCUMENT IS THE PROPERTY OF FAIRVIEW MICROWAVE CORPORATION. ALL RIGHTS RESERVED. K.DANG AFMAM1077 ALL DIMENSIONS SHOWN ARE FOR REFERENCE ONLY. DRAWN BY THIRD-ANGLE PROJECTION SHEET OF A SCALE SIZE 3FKR5 UNLESS OTHERWISE SPECIFIED LEADING DIMENSIONS ARE INCHES DIMENSIONS IN [ ] ARE MILLIMETERS REV 1 1 N/A ITEM NO.CAGE CODE THESE COMMODITIES, TECHNOLOGY OR SOFTWARE WERE EXPORTED FROM THE UNITED STATES IN ACCORDANCE WITH THE EXPORT ADMINISTRATION REGULATIONS. DIVERSION CONTRARY TO U.S. LAW PROHIBITED. °ANGLES ± 1 ± 1/32 FRACTIONS.2 [5.08].X = ± .XX = ±.02 [ .51 ] TOLERANCES: CABLE LENGTH (L) TOLERANCES: T-Rev.D FMAM1077 DATA SHEET 35 dB Gain Waveguide Low Noise Amplifier Operating from 27 GHz to 40 GHz with 3 dB NF, 12 dBm Psat and WR28