FCTE CYNERGY3 | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
- Prevents dry-running of pump
- Prevents overheating of seals
- High power switching capacity The FCTE is a heat sensor, which is attached to the outlet pipe from a pump. This device works by reacting to the temperature at the outlet of any centrifugal type pump, which will rapidly rise past 45 ° if the inlet water level falls below the centre line of the inlet. The unit will cut off the electrical supply to the pump, so protecting it from damage. Manual resetting of this unit allows the pump to restart. SPECIFICATION Set Temperature 45°C 113°F Switching voltage max. 250Vac Switching current max. resistive 16A Pipe diameter range 20-200mm IP Rating 21 INSTALLATION Heat accumulation zone due to vapour formation TE thermostat TE thermostat also protects the seal Level of water when TE cuts in Spring clip fixing sensor to pipe Dia. min 20 max 400 46 reset button64 indicator light cable entry Top View heat sensor brass strip i m in a d a eter. m 20 m x 400 pipe Side View brass heat conductor strip reset button indicator light cable entry three-phase motor pump protection A - A20 examples of positioning TE thermostat16 A 250V 250V single - phase motor pump protection pump thermic relay heat sensor spring clip fixing sensor to pipe FCTE Pump Dry Running Sensor FCTE 2013 cynergycomponents cynergycomponents Cynergy3 Components Ltd
7 Cobham Road
Ferndown Industrial Estate Wimborne Dorset BH21 7PE Tel: +44 (0) 1202 897969 sales@cynergy3.com www.cynergy3.com www.cynergy3.com ISO 9001 ISO 9001 CERTIFIED CERTIFIED © 2013 Cynergy3 Components, All Rights Reserved. © 2013 Cynergy3 Components, All Rights Reserved. Specifications are subject to change without prior notice. Cynergy3 Components and the Cynergy3 Components logo are trademarks of Cynergy3 Components Limited. Specifications are subject to change without prior notice. Cynergy3 Components and the Cynergy3 Components logo are trademarks of Cynergy3 Components Limited.
- Prevents dry-running of pump
- Prevents overheating of seals
- High power switching capacity The FCTE is a heat sensor, which is attached to the outlet pipe from a pump. This device works by reacting to the temperature at the outlet of any centrifugal type pump, which will rapidly rise past 45 ° if the inlet water level falls below the centre line of the inlet. The unit will cut off the electrical supply to the pump, so protecting it from damage. Manual resetting of this unit allows the pump to restart. SPECIFICATION Set Temperature 45°C 113°F Switching voltage max. 250Vac Switching current max. resistive 16A Pipe diameter range 20-200mm IP Rating 21 INSTALLATION Heat accumulation zone due to vapour formation TE thermostat TE thermostat also protects the seal Level of water when TE cuts in Spring clip fixing sensor to pipe nDia. mi 20 max 400 46 reset button64 indicator light cable entry Top View heat sensor brass strip i met . min 20 max 400 d a er pipe Side View brass heat conductor strip reset button indicator light cable entry three-phase motor pump protection A - A20 examples of positioning TE thermostat16 A 250V 250V single - phase motor pump protection pump thermic relay heat sensor spring clip fixing sensor to pipe FCTE Pump Dry Running Sensor FCTE 2013 cynergycomponents cynergycomponents Cynergy3 Components Ltd
Ferndown Industrial Estate Wimborne Dorset BH21 7PE Tel: +44 (0) 1202 897969 sales@cynergy3.com www.cynergy3.com www.cynergy3.com ISO 9001 ISO 9001 CERTIFIED CERTIFIED © 2013 Cynergy3 Components, All Rights Reserved. © 2013 Cynergy3 Components, All Rights Reserved. Specifications are subject to change without prior notice. Cynergy3 Components and the Cynergy3 Components logo are trademarks of Cynergy3 Components Limited. Specifications are subject to change without prior notice. Cynergy3 Components and the Cynergy3 Components logo are trademarks of Cynergy3 Components Limited.